MiCODUS 4G MV710G User Manual V1.0
Learn how to set up your new MiCODUS Tracker
1. Main Features
- 4G LTE+ 2G GSM
- GPS+BDS
- Remotely Cut Off / Resume Fuel
- Realtime Tracking
- Historical Route Playback
- Vibration Alarm
- 9-95V Wide Working Voltage
- ACC Status Detection
- Tow Alarm
- Power failure alarm
- Geo-fence
- Engine On/OFF Alarm
- Battery low voltage alarm
- Overspeed Alarm
- Lifetime Free Tracking Platform
- iOS & Android APP
2. Specifications
| Device Information | Model | MV710G |
| Weight | 40g | |
| Dimensions | 79mm(L)*33mm(W)*16mm(H) | |
| Battery | Built-in 60 mAh 3.7V polymer battery | |
| Working Parameters | Working Voltage | 9-95V DC |
| Working Current | 12V/average 35mA | |
| Sleep Current | 12V/average 10mA | |
| Working Temperature | -20°C - 75°C | |
| Working Humidity | 10%-85% RH non-condensing | |
| Cellular Specifications | SIM Card | Micro SIM |
| Cellular Antenna | Built-in, FPC | |
| Working Frequency | GSM/2G: 850/900/1800/1900MHz LTE/4G: LTE-FDD:B1/B2/B3/B4/B5/B7/B8/B28/B66 |
|
| GNSS Specifications | GNSS | GPS+BDS |
| GPS Frequency | L1: 1575.42±1.023MHz | |
| BDS Frequency | B1:1561.098±2.046MHz | |
| Sensitivity | -162 dBm | |
| Satellite Channels | 32 | |
| Hot/Cold Start | <1s, <32s @ Open Sky | |
| Positioning Antenna | Built in ceramic dielectric antenna, 18*18*4mm | |
| Accuracy | <10m (1σ) | |
| ACC Detection | 1 | |
| External Interface | Cut Off Fuel/Power | Standard |
| SOS (optional) | 1 | |
| Open door Alarm (optional) | 1 | |
| Microphone | 1 |
3. How to manage the tracker to get online?
Step 1: SIM Card Requirements
Please get a suitable SIM card from your local place. The SIM card must meet below points:
- It must be compatible with the 4G LTE or 2G GSM network.
- Please enable SMS, call, and internet data traffic of the SIM card.
- Enable the caller ID display feature.
- Remove the PIN code.
- Use Nano size SIM card for the tracker.
- Please inquire the SIM card provider for the exact correct APN information.
Step 2: SIM Card Installation
Refer to the diagrams for SIM card installation.
Step 3: Wiring
Refer to the wiring diagram for connecting the tracker. Ensure the power supply is no less than 12V.
Step 4: Configure APN
Please get the exact correct APN name from your local SIM card provider. Take the tracker to a good signal place for operation and configure the APN for it as below:
| SMS Command Format | Reply | Example | Note |
| APN,ApnName,User,Password# | SET APN OK | APN, orange, orange,orange# | If the SIM card has APN user and APN password, then use this command. |
| APN,ApnName# | SET APN OK | APN, internet# | If the SIM card operator doesn't have APN user and APN password, then please use this command. |
Note: The APN information is very important and must be 100% correct to match the SIM card of the tracker. If you configure the wrong APN, the tracker will reply "SET APN ok" but it will not get online.
Step 5: Indicator Status Description
| LED | Event | State |
| CELL LED (YELLOW) | Searching for network | Flash every 1 second |
| Network has been registered | Solid | |
| GPS LED (BLUE) | GPS is in fixing | Flash every 1 second |
| GPS has fixed | Solid | |
| ALL LED | Device is working but stopped more than 5min | |
| Device has not been turn on | ALL LED TURN OFF | |
| Device ran out of battery |
4. Package Content
- GPS Main Unit x 1
- Function Cable x 1
- User Guide x 1
- Genuine Packing Box x 1
5. Functions Explanation
a. Cut Off Fuel/Resume Fuel
* Set center number by this sms command: CENTER,A,center number#
* Send this sms command from the center number: RELAY,A#
A=0/1/2; (0: Resume Fuel; 1: Cut Off Fuel Immediately; 2: Cut Off Fuel Safely)
For example: RELAY,1# (FUEL WILL BE CUT OFF IMMEDIATELY)
b. Vibration Alert
This vibration alert function works under stationary status.
* Configure SOS numbers: SOS,A,1st number,2nd number,3rd number# (Supports up to 3 SOS numbers)
* Enable arm mode: ARM#
* Configure alarm ways: SENALM,[A][,M]#
A=ON/OFF (default: OFF); M=0/1/2 (way of alarming: 0: GPRS only, 1: SMS+GPRS, 2: GPRS+SMS+phone call, default:1)
Keep the device stationary for over 5 minutes to enter sleep arm mode. Vibrate the device to send vibration alarm messages.
c. External Battery Low Voltage Alarm
* Command format: LVALM,A,B,M#
A=ON/OFF (default: ON); B=9-95V (voltage alarm threshold, default: 11.1v); M=0/1/2 (way of alarming: 0: Server only, 1: SMS+Server, 2: SMS+Server+Call, default:1)
Example: LVALM,ON,11.5,1# (Sends alarm message when external battery voltage is less than 11.5v)
d. Engine Start and Flameout Alarm
* Command format: ACCALM,A,B,M#
A=ON/OFF (Default: ON); B: 0/1/2 (0: ACC ON Alarm; 1: ACC OFF Alarm; 2: ACC ON&OFF Alarm; Default:2); M: 0/1/2 (way of alarm: 0: Server only, 1: SMS+Server, 2: SMS+Server+Call, Default:1)
Example: ACCALM,ON,2,1# (Sends alarm message on engine start and flameout)
6. Installation Recommendation
Diagram showing recommended installation locations on a car and motorcycle:
- Car: Under front windshield, Under rear windshield, Inside Door Pedal, Around dashboard, Inside the taillight component or plastic, Inside the head light, Inside the front cover, Under the pedal.
- Motorcycle: Under front windshield, Inside the taillight component or plastic, Under the pedal, Inside Door Pedal, Around dashboard, Inside the head light, Inside the front cover.
1) The device should face up to the sky.
2) Metal thermal barrier of the windshield affects the signal.
7. Troubleshooting
| Type | Use |
| Unable to connect to tracking platform | Check the APN and settings. Check whether the data service of SIM card is enabled. Check the balance of SIM card. |
| Tracker shows offline | Check whether external power is still connected. Check if the vehicle entered network blind area. Check the balance of SIM card. |
| Unable to locate | Make sure the top side facing upward without metallic things shielded. Make sure it's not in an area with no satellite coverage. |
| Location drift | In areas with poor GNSS signal (tall building around or basement), drifting may happen. Check whether vibration happens around to trigger the accelerator. |
| No command reply | Make sure command format is correct. Vehicle may be in network blind area. Make sure SIM card is well inserted and has SMS service. |
8. Full SMS Commands List
Setting Commands
| Functions | Command Format | Explanation |
| APN Setting | APN,Network name[,name,password]# | APN,CMNET# (if no name & Password) APN,internet,internet,internet# (if with name & Password) |
| Server Setting | If set with Domain Name: SERVER,1,Domain,Port# If set with IP: SERVER,0,IP,Port# |
SERVER,1,d.micodus.net,7700# SERVER,0,47.254.77.28,7700# |
| Check IMEI | IMEI# | DEVICE IMEI No. : 0123456789 |
| Change IMEI | IMEICHG,354188046912460# | NEW IMEI No. : 354188046912460 |
| Restore factory settings | FACTORY# | RESTORE FACTORY SETTINGS OK |
| Restart device | RESTART# | RESTARTING...1 MINUTE WILL BE OK |
| Internet Traffic Switch | TRAFFIC,ON# TRAFFIC,OFF# |
OPEN TRAFFIC OK CLOSE TRAFFIC OK |
| Time Zone Setting | GMT,A,B,C# | Example: GMT,E,8# (Means East +8 zone, no half time zone) GMT,W,9,30# (Means West -9.5 zone, has half time zone) A: E / W, E: East time zone, W: West time zone B: 0 ~ 12; whole time zone C: 0/15/30/45, half time zone |
| Set the angle upload | ANGLEREP,X,A,B# | Example: ANGLEREP,ON,30,3# (Means the tracker will send a data supplement when the angle change exceeds 30 degrees and lasts for 3 seconds) X=ON/OFF, default: ON; A=5~180 degrees, diversion angle degree, default: 30 degrees; B=2~5 seconds, detecting time, default: 3 seconds, |
| ANGLEREP,OFF# | CANCEL UPLOAD ANGLE OK | |
| Mileage Statistics | MILEAGE,A,B# | Example: MILEAGE,ON,5000# (Means enable the mileage statistics feature, the mileage initial value is 5000km) A=ON/OFF, On/Off mileage calculation, default: Off B=0~999999, Mileage initial value, unit: km; default: 0, mileage return to zero |
| MIELEAGE# | Query current mileage | |
| Add SOS Administrator Number | SOS, A, 1st number, 2nd number, 3rd number# | Example: Set 3 numbers at a time: SOS,A,13800138000,13800138001,13800138002# Set the first number separately: SOS,A,13800138000# Set the second number separately: SOS,A,,13800138001# Means to set 3rd number separately: SOS,A,,,13800138002# |
| Delete SOS Administrator Number | SOS,D, 1st number, 2nd number, 3rd number# or SOS,D,1,2,3# | Example: Directly delete the number: SOS,D,13800138000# Delete 1st number: SOS,D,1# Delete 2nd number: SOS,D,2# Delete the 2nd and 3rd number: SOS,D,2,3# |
| Add Center Number | CENTER, A, center number# | Example: CENTER,A,008613800138000# (Means the tracker will just be controlled by this number 008613800138000, 0086 is country code) NOTE: 1. Please set up the center number with the country code as prefix! 2. After set up center number, the tracker will just can be controlled by center number, it will not reply commands from other numbers! |
| Delete Center Number | CENTER,D# | DEL CENTER OK |
| Data Upload Time Interval | TIMER,T1,T2# | Example: TIMER,5,180# (Means the tracker will upload data every 5s when ACC is on and 180s when ACC is off) T1 ranges 0/5~18000 or 0(seconds), upload interval when ACC ON, 0 means no upload, default is 10; T2 ranges 0/5~18000 (seconds), upload interval when ACC OFF, default is 10; |
| Heartbeat Packet Upload | HBT,time# | Example: HBT,3# (Means the tracker will send heartbeat data package to server every 3 min for connection maintenance) NOTE: Range :1-60min, default 3min. |
| Sensor Sensitivity | LEVEL,A# | Example: LEVEL,2# (Means set up the shake sensor level to 2) NOTE: A: Sensitivity Level 1-9 (1-9 is from week to strong vibration) |
| Arm manually | ARM# | Set the device into arm mode |
| Disarm manually | DISARM# | Set the device out of arm mode |
Inquiry Commands
| Functions | Command Format | Explanation |
| Version Inquiry | VERSION# | Device Reply Example: ID:9301074948 IMEI:354188046912460 ICCID:898602A51314F1298017 VERSION:MV930G_V2.0.2 BUILD:OCT 19 2016 16:31:00 |
| Parameter Inquiry | PARAM# | Device Reply Example: ID:9301074948 IMEI:861157040411486 APN:CMNET IP:47.254.77.28:7700 TIMER:10,180 SPEEDLIMIT: 120km/h ANGLERPT: 30' CENTER: 13428768257 SOS:13267052361,13488888888,13599999999 GMT:E8.00 |
| Latitude&Longitude Inquiry | WHERE# | LAT:N23.02930,LON:E114.32180,COURSE:0.00,SPEED:0.00KM/H,DATETIME:2015-05-23 14:39:11 |
| Map URL Inquiry | URL# | http://map.google.com/?q=22.557868,113.935090<0.0km/h 0.0> <2014-12-12 07:32:13> IMEI:354188047752402 |
| Address Inquiry | POSITION# | NOTE: Reply message's language is determined by device's language setting, if get position content failed, device will reply Google Map location link. |
| Status Inquiry | STATUS# | BATTERY: XX% (Built-in Battery Power Percent) INTERNET: CLOSED (No Network) FAILED (Connecting Network or Failure) SUCCESS (Connected to Network) NET: NONE (No celluar Signal), HIGH / MED / LOW (Signal Strength), 18(Signal value) GPS: CLOSED (GPS Module Closed); FIXED,N (Positioned and satellite number); UNFIX,0 (Not Positioned yet) SPEED: 30KM/H ACC: ON / OFF (ACC on or off) RELAY: ON / OFF (Relay on or off) POWER: CONNECTED / DISCONNECTED (Power Connected or Disconnected), 12.5V (Vehicle battery voltage) SENSOR: ON/OFF (Sensor on or off), LEVEL: 3 (Sensitivity level 1-9) STATE: ARM (Arm or Disarm) |
| Alarms Parameters | ALARM# | ID: 19172012644 (ID number of device) STATE: ARM(DISARM)(Defense status of device) SPEED: ON/OFF(alarm status); 30km/h(alarm value);alarm way SHIFT: ON/OFF(alarm status); 300m(alarm value); alarm way VIBRATE: ON/OFF(alarm status);3(sensitivity level); alarm way ACC: ON/OFF(alarm status); 0/1/2(0: ACC ON, 1: ACC OFF; 2: ACC ON&OFF) (alarm situation); alarm way;; POWER DOWN: ON/OFF(alarm status);alarm way LOW VOLTAGE: ON/OFF(alarm status);alarm way NOTE: Alarm Ways: 0/1/2 (0 : SERVER only, 1: SMS+GPRS, 2 : GPRS+SMS+CALL ) |
Alarm Commands
| Functions | Command Format | Explanation |
| Overspeed Alarm Setting | SPEED,A,B,M# | Example: SPEED,ON,100,1# (When the speed of the tracker exceeds 100km/h it will send alarm message via SMS and server) A=ON/OFF, enable or cancel over speed alarm, default: OFF B=1~255(km/h), speed limit, default: 100(km/h); M=0/1/2, way of alarm, 0 : Server only, 1: SMS+Server, 2: SMS+Server+Call default: 1. |
| SPEED,OFF# | CANCEL OVERSPEED ALARM OK | |
| Vibration Alarm Setting | SENALM,A,M# | Example: SENALM,ON,2# (Means enable the vibration alarm, and the alarm message will be sent via SMS, server and call once it is triggered) A=ON/OFF, default: OFF; M=0/1/2, way of alarming, 0 : Serveronly, 1: SMS+Server, 2: SMS+Server+Call, default:2 |
| SENALM,OFF# | CANEL VIBRATE ALARM OK | |
| Shift Alarm Setting | SHIFT,A,B,M# | Example: SHIFT,ON,300,1# (Means Setting 300 meters shift alarm range, when the ignition turned off, vehicle's 300 meters' shift will trigger the alarm, the alarm message will be sent via SMS and server) A=ON/OFF; default:ON B=Shift Distance (Range: 100-9999m) M=0/1/2; way of alarm, 0 : Server only, 1: SMS+Server, 2: Server+SMS+CALL, default:1 |
| SHIFT,OFF# | CANCEL SHIFT ALARM OK | |
| Auto Arm By ACC | ACCARM,ON,M# | Example: ACCARM,ON,60# (Means when the engine turned to off status, the tracker will enter into arm status automatically after 60s) Arm Time: M=5-1800s, default: 60s |
| ACCARM,OFF# | Close auto arm function | |
| ACC Status Change Alarm | ACCALM,A,B,M# | Example: ACCALM,ON,2,2# (Means enable this alarm type, tracker will send alarm message via SMS, server and call when engine start and flameout) A=ON/OFF, Default: ON; B: 0/1/2; 0: ACC ON Alarm; 1: ACC OFF Alarm; 2: ACC ON&OFF Alarm; Default:2 M: 0/1/2 (way of alarm): 0 : Server only, 1: SMS+Server, 2: SMS+Server+Call, Default:1; |
| ACCALM,OFF# | Cancel ACC alarm function | |
| Power Disconnect Alarm | PWRALM,A,M# | Example: PWRALM,ON,1# (Means when the external power disconnect the tracker will send alarm message via SMS and server) A=ON/OFF, default ON; M=0/1/2, ways of alarming, 0: Serveronly, 1: SMS+Server, 2 : SMS+Server+Call, default:2; |
| PWRALM,OFF# | Close power disconnect alarm | |
| Low Voltage Alarm Setting | LVALM,A,B,M# | Example: LVALM,ON,11.2V,1# (Means once the external power voltage is less than 11.5v the tracker will send alarm message out via SMS and server) A=ON/OFF, default: ON; B=9-95 V, Low voltage threshold, can be a decimal, such as 12.5 V M=0/1/2, way of alarming, 0: GPRS only, 1: SMS+GPRS, 2: SMS+GPRS+Call,default:1 |
| LVALM,OFF# | CANCEL LOW VOLTAGE ALARM OK |
9. Any Questions?
E-mail: support@micodus.com
Skype: MiCODUS
10. Download the APP
Search "MiCODUS" in iOS APP store or Google Play Store, or just scan the QR code as below to download MiCODUS APP:
[App Store Download Button] [Android Download Button]
Spionlink - SIM Card Service | Prepaid Data Plan | GPS Tracker Supplier
