GOOLOO GP Warrior Jump Starter User Manual

Diagram of the GOOLOO jump starter unit showing its components: Indicator lights, Switch, Jump Start Socket, 5V/2A Input Port, 5V/2.4A Output Port, 5V/1A Output Port, and LED Flash Light.

The indicator lights will flash one by one when charging. Different numbers of solid indicators show the battery storage level of the GOOLOO starter. All indicators will be off when charging is paused or completed.

1. Indicator

Press the Power button to check the remaining battery of the GOOLOO GP Warrior.

2. Recharge the unit

1. Plug the USB charging cable into any working USB output port.
2. Connect the Micro connector to the GP Warrior host.

The GOOLOO GP Warrior is designed for jump starting 12V vehicle batteries.

Step 1:

Fully plug the blue connector of the clamp cable into the jump starter socket, and ensure the indicator on the clamp cable is off.

Step 2:

Connect the Red Clamp to the positive(+) battery terminal and the Black Clamp to the negative(-) battery terminal.

Step 3:

Operate according to the indicator on the clamp cable:

• GREEN LIGHT on: Indicates the connection is correct and the circuit is working. You can turn on the engine to jump start directly.
• RED LIGHT on with buzzing ?: Indicates the connection is wrong. The unit will buzz to alert you to correct the clamps as described in Step 2. Wait until the GREEN LIGHT is on before turning on the engine.
• GREEN LIGHT blinking with buzzing ?: Indicates the vehicle battery is low. Press the "BOOST" button, wait until the GREEN LIGHT becomes solid, then turn on the engine within 30 seconds.
• No Lights on, No buzzing: Indicates the vehicle's battery may be damaged. After confirming that the clamps are connected correctly, press the "BOOST" button, wait until the GREEN LIGHT is on, and then turn on the engine within 30 seconds.

Visuals illustrate connecting the clamp cable, connecting red and black clamps to battery terminals, and the status indicators on the clamp cable.

Step 4: Start the vehicle.

The word "START" is shown next to a car ignition key graphic.

Step 5:

When the vehicle is started, remove the clamp cable from the jump starter first, then remove the clamps from your vehicle battery.

Visuals show removing the clamp cable from the jump starter and then from the vehicle battery.

Cautions:

• Occasionally, the jump starter will lock itself down for safety due to (a) short-circuit; (b) over-current; (c) over-temperature; (d) over/low-voltage; (e) reverse-connection. If this occurs, turn off the jump starter, remove the battery clamps from your car battery, restart the jump starter, and reconnect the clamps to the battery. Try again.
• If the vehicle does not start within 3 seconds, stop starting and wait at least 30 seconds before attempting to restart the vehicle. Do not jump start the vehicle continuously more than four times, as it may damage the unit. Check your vehicle for other possible reasons of not starting.
• During jump starting, avoid the positive (+) and negative (-) battery clamps touching each other. Otherwise, electric spark will appear, resulting in a safety hazard and damage to the unit by short circuit.
• This unit contains a lithium polymer battery. It is only used as an emergency power source and not to replace a car battery. Always comply with transport and safety regulations in the use and disposal of such batteries.

4. Charge your phone or tablet

Visuals show a jump starter unit with USB output ports and icons representing a phone/tablet being charged.

Step 1:

Plug the switch cable into a USB output port.

Step 2:

Select the appropriate connector and connect it to your mobile phone or tablet.

Step 3:

Press the switch button to charge.

Step 4:

If it doesn't work, please try another USB Cable or USB Output port.

5. Use the LED Flash Light

• Long press the Power button for 3 seconds to start the LED flash light.
• Short press the Power button; there are 3 modes of LED light available: torch light, strobe, or SOS switchable.

Q. How to turn off this appliance?

A. This appliance will shut off automatically when there is no load or charging is completed.

Q. How to jump start a vehicle with GOOLOO jump starter?

A. 1). Make sure it is over 60% charged. If it has not been used for more than two months, please charge it first. 2). Turn it on and connect the red clamp to "+", the black clamp to "-", at the end of the car battery. 3). Start the car, unplug the jumper cables from the jump starter within 30 seconds, and remove the clamps from your car battery.

Q. What should I do if the GOOLOO jump starter cannot be charged?

A. Charge it with a different charging cable to test. If it still does not work, email us via contact@gooloo.com.au (Within the 12-month warranty period, please attach your order ID for confirmation).

Q. What should I do if GOOLOO jump starter cannot charge other devices?

A. Use a different charging cable to charge again. If it works, the charging cable must be defective; email us and we will provide a new cable. If it still does not work, email us via contact@gooloo.com.au (Within the 12-month warranty period, please attach your order ID for confirmation).

Q. How long does the battery last in sleeping mode?

A. 6-12 months, however, we suggest recharging it every 3 months.

• ? Recharge at least once every 3 months
• ? Do not expose to liquids
• ⬇️ Avoid dropping
• ? Use original or certified cables
• ? Do not modify or disassemble
• ?️ Avoid extreme temperatures

• Read the instruction manual carefully before using this unit.
• The product needs to be fixed in place when you keep it in the trunk.
• Do not place the product in any high-intensity magnetic field to avoid damage to its components.
• Before the first use, please charge the jump starter for at least 3 hours.
• Please keep the remaining power above 20%.
• Keep children away from this unit.
• Do not use this unit if any cable clamp or cord is damaged.
• Never use or leave the unit connected to a car battery after cranking the car.
• Make sure the blue plug of the jumper cable is fully plugged into the jumping socket; otherwise, the blue plug could melt.
• Ensure and check that the battery connections and the battery clamps are well connected before jumping start! If the battery terminals on the vehicle are dirty or corroded, the unit's power will be lessened.
• Remove the product from the vehicle battery within 30 seconds of Jump Starting. Failure to do so could lead to damage.
• Do not operate the product in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
• Remove personal metal items like rings, bracelets, necklaces, etc., when using the products.
• Do not use the unit to jump start a vehicle while charging the internal battery.
• If this unit is leaking liquid, dispose of it at a proper recycling facility immediately. If liquid is noticed coming from the product, do not handle it with bare hands. If the jump starter is inflating, please stop using it.
• Do not toss it into the trash or your regular recycling bin after use. Please recycle it according to your local environmental rules.

• Battery Capacity: 20800mAh/76.96Wh
• Starting Current: 500A (3s)
• Peak Current: 2000A
• Output: 5V=1A; 5V=2.4A
• Input: 5V=2A
• Full Charging Time: 5-6 hours
• Discharge Temperature: -20°C~40°C
• Charge Temperature: 0°C~45°C
• Main unit N.W.(g): 580g
• Size: 208*89*28.5mm (L*W*H)

Customer Services

One-year warranty from the date of purchase. If you have any questions/problems about using the product, please feel free to contact us. Our customer service team is always at your service: contact@gooloo.com.au

Logos present include SGS, FC, CE, RoHS. Product is MADE IN CHINA.