TFA Transmitter for Temperature and Humidity

Introduction

Thank you for choosing this instrument from TFA Dostmann. Before using this product, please read the instruction manual carefully. The manual is enclosed with the device or can be downloaded from www.tfa-dostmann.de/en/service/downloads/instruction-manuals. This product should only be used as described within these instructions. Following and respecting the instructions will prevent damage to your instrument and loss of statutory rights. Please take particular note of the safety advice and keep this manual for future reference.

Range of Application and Benefits

• Transmitter for TFA wireless stations (e.g., models 30.3057.01, 30.3058.01, 35.1129.01, 35.1139.01, 35.1140.01, 35.1150.01, 35.1160.01, 35.1161.01, 35.1162.54, 35.1164.02).
• Replaces older transmitters (models 30.3221.02 and 30.3206.02).
• Wireless transmission of temperature and humidity (433 MHz).
• Transmission range up to 100 m (in open field).
• Suitable for indoor or outdoor use.
• Displays temperature and humidity.

Components

Transmitter Display (Fig. 1)

• A - Channel 1/2/3 indicator
• B - Transmission signal indicator
• C - Temperature reading
• D - Humidity reading
• E - Low battery symbol

Transmitter Housing (Fig. 2)

• A - TX button (for manual transmission)
• B - 1/2/3 slide switch for channel selection
• C - Battery compartment
• D - Holder for table standing
• E - Indentations for wall mounting holder

Figure 3 shows the wall mounting of the transmitter.

Getting Started

1. Set up the base station according to its instruction manual.
2. Open the battery compartment of the transmitter and insert two new 1.5 V AA batteries, observing correct polarity. All LCD segments will briefly light up. The temperature and humidity will appear on the display. Data transmission is immediate.
3. If connecting multiple transmitters, select a different channel for each using the 1/2/3 switch inside the battery compartment.
4. To activate transmission manually, press the TX button.
5. Close the battery compartment.

Installation

• For outdoor use, choose a shady and rain-protected location for the transmitter. Direct sunlight can falsify measurements, and constant moisture can unnecessarily strain electronic components.
• Before final installation, verify that measured values are transmitted from the desired location to the base station.
• Avoid placing the transmitter near other electrical devices (TVs, computers, cordless phones). Thick walls, especially those with metal parts, can significantly reduce the transmission range (max. 100 m).
• For wall mounting, screw the holder to the wall and click the transmitter into the holder (Fig. 3).

Battery Replacement

• When the low battery symbol (Fig. 1 E) appears on the display, replace the transmitter batteries.
• Note: After replacing batteries, re-establish contact between the transmitter and base station by restarting both devices or initiating a manual transmitter search.

Safety Information

WARNING

• Keep the device and batteries out of reach of children.
• Small parts can be swallowed by children (under three years old).
• Batteries contain harmful acids and can be dangerous if swallowed. Ingestion can lead to severe internal burns and death within two hours. Seek immediate medical help if a battery is suspected to have been swallowed or ingested.
• Do not throw batteries into fire, short-circuit, disassemble, or recharge them. Risk of explosion!

CAUTION

• Unauthorized repairs, alterations, or modifications to the device are prohibited.
• Do not expose the device to extreme temperatures, vibrations, or shocks.
• Clean the device with a soft, slightly damp cloth. Do not use abrasive cleaners or solvents.
• The transmitter is splash-proof but not waterproof.

Battery Handling: Replace weak batteries promptly to prevent leakage. Ensure correct polarity. Do not mix old and new batteries or different battery types. Remove batteries if the device is not used for an extended period. Avoid contact with skin, eyes, and mucous membranes when handling leaking batteries. Rinse affected areas with water and consult a doctor if contact occurs.

Technical Specifications

Disposal

This product and its packaging are made from high-quality, recyclable materials, reducing waste and protecting the environment. Dispose of packaging responsibly through designated collection systems.

Electrical Device Disposal

Remove non-permanently installed batteries and rechargeable batteries separately. This device is WEEE-compliant and must not be disposed of with household waste. Consumers must take end-of-life devices to designated collection points for environmentally compatible disposal, adhering to current regulations.

Battery Disposal

Do not dispose of used batteries with household waste, as they contain pollutants harmful to the environment and health. Consumers are legally obligated to return used batteries to retailers or designated collection sites according to national or local regulations for environmentally sound disposal. Heavy metal designations: Cd=cadmium, Hg=mercury, Pb=lead.

EU Declaration of Conformity

TFA Dostmann declares that the radio equipment type 30.3249.02 complies with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at: www.tfa-dostmann.de/service/downloads/ce.

Reproduction of this manual, even partial, is prohibited without TFA Dostmann's explicit consent. Technical data are current at the time of printing and may change without prior notice. Latest technical data and product information can be found on the TFA Dostmann homepage by entering the article number.

Contact: info@tfa-dostmann.de

TFA Dostmann GmbH & Co.KG
Zum Ottersberg 12
97877 Wertheim
Germany

11/2021