allen + roth 10 ft x 10 ft LED Lighted Offset Patio Umbrella

Product Details

Item #: 5103062

Model #: AG45-ELSDT2-30S-LS

Diagram Description

A detailed illustration shows the offset patio umbrella structure. It features a large, square canopy supported by ribs, a central pole with a crank mechanism, and a base. A solar panel is visible at the top of the umbrella's finial.

Table of Contents

• Package Contents
• Hardware Contents
• Safety Information
• Preparation
• Assembly Instructions
• Operating Instructions
• Care and Maintenance
• Troubleshooting
• Warranty
• Replacement Parts List

Package Contents

• A - Umbrella (1)
• B - Solar Panel (1)
• C - Rotating Hub (1)
• D - Metal Stand (2)
• E - Plastic Base Interior (2)
• E1 - Plastic Base Exterior (2)
• F - AC Adaptor (1)
• FF - Base Plug (4)
• G - Bolt A (7)
• H - Bolt B (1)
• I - Small Washer (1)
• J - Rib Cap (1)
• K - Canopy (1)
• L1 - Light Bar 1 (3)
• L2 - Light Bar 2 (4)
• M - Finial (1)
• N - Cap (1)
• AA - Large Wrench (1)
• BB - Small Wrench (1)
• CC - Bolt (6)
• DD - Washer (6)
• EE - Crank Handle (1)

Hardware Contents

• AA - Large Wrench (Qty: 1)
• BB - Small Wrench (Qty: 1)
• CC - Bolt (Qty: 6)
• DD - Washer (Qty: 6)
• EE - Crank Handle (Qty: 1)

Safety Information

Read and understand this entire manual before attempting to assemble, operate or install the product.

WARNING

Assemble on a soft, non-abrasive surface, such as a carpet, to avoid damage. Item is heavy. Use care when handling. May require two adults for safe assembly. Crank the umbrella to its closed position during windy weather conditions.

This outdoor umbrella is designed and made for personal non-commercial use. It should not be used as a toy or a tool. Children under 16 should not be engaged in assembly, removal or disassembly. Children under 10 should be supervised by a competent adult while using this furniture.

NOTE

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) This device may not cause harmful interference, (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna; Increase the separation between the equipment and receiver; Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

CAUTION

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

To prevent personal injury or damage, always take down the umbrella when not in use, during windy conditions or in rain. Do not operate or attempt to charge the umbrella when water is present so as to prevent damage to the electrical components.

Preparation

Before beginning assembly, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble, install or operate the product.

Estimated Assembly Time: 40 minutes

Tools Required for Assembly (included): [Large Wrench]

Assembly Instructions

Step 1: Metal Stand Assembly

Assemble the Metal Stand (D) by overlapping the metal bars together on the ground in a cross pattern as shown.

Step 2: Rotating Hub Attachment

Line up the mounting holes in the Rotating Hub (C) on top of the Metal Stand (D). Press down on the pedal to rotate the Rotating Hub (C) so that the two channels of the Rotating Hub (C) line up with two mounting holes. Secure the Rotating Hub (C) to the Metal Stand (D) with 2pcs Bolts (CC) and 2pcs Washers (DD). Tighten with the Large Wrench (AA). Repeat the process lining up the two channels of the Rotating Hub (C) with the two remaining holes. Insert 2pcs Bolts (CC) and 2pcs Washers (DD) into the two remaining holes and tighten with the Large Wrench (AA).

Step 3: Base Filling

Remove each Base Plug (FF) by turning counter-clockwise. Using a funnel (not included), fill each section of Plastic Base (E/E1) with 50-lbs to 60-lbs of sand or pea gravel (not included), pouring water into the base intermittently to help pack the sand (water and material should total 220-lbs to 250-lbs for all four). Screw the Base Plug (FF) clockwise back into place. Ensure that the rubber gasket is present on the Base Plug (FF) to prevent the Plastic Base (E/E1) from leaking water. When filling, leave a small void in the base to allow room for the water to expand when it freezes in the winter. Each section requires a minimum of 50-lbs of sand or pea gravel and water. Water alone will not support the weight of the cantilever.

Step 4: Base Assembly

Assemble the Plastic Base (E/E1) by interlocking the 4pcs together onto the Metal Stand (D). NOTE: You may need to reposition the pedal on the Rotating Hub (C) in this step. To do this, press down on the pedal and rotate either direction to reach desired position.

Step 5: Finial and Solar Panel Assembly

Locate the Finial (M) and the Solar Panel (B). Separate the Cap (N) from the Finial (M) by twisting the Cap (N) counter-clockwise approximately 1/4 turn and pulling apart. With the Cap (N) removed from the top of the Finial (M), line the tabs on the bottom of the Solar Panel (B) up with the slots inside the top of the Finial (M). Insert the bottom of the Solar Panel (B) into the top of the Finial (M) and twist clockwise approximately 1/4 turn until it is secure.

NOTE: To increase the lifespan of the Solar Panel (B) it is recommended it be removed and stored away when not in use for extended periods of time.

With the Solar Panel (B) installed securely onto the top of the Finial (M), insert the threads on the bottom of the Finial (M) into the top of the Umbrella (A). Turn the Finial (M) clockwise to tighten the threads until the Finial (M) is secure on the Umbrella (A). Check to ensure that the Solar Panel (B) did not come loose in this process and is still securely on top of the Finial (M).

Step 6: Crank Handle Installation

Fit the Crank Handle (EE) over the crank mechanism. Secure the Crank Handle (EE) onto the crank mechanism using the Small Wrench (BB) to tighten the setscrew.

Step 7: Pole Attachment

Line up the two holes in the bottom of the Umbrella (A) pole with the Rotating Hub (C) and slide the Umbrella (A) pole down over the Rotating Hub (C). Using the Large Wrench (AA), secure the Umbrella (A) pole to the Rotating Hub (C) with 2pcs Bolts (CC) and 2pcs Washers (DD).

Operating Instructions

Opening the Umbrella

With the umbrella in an upright position, unfasten the storage tie from the canopy. Gently spread the umbrella ribs and fabric by hand to free up parts that may have become wedged during shipping.

To prevent undue stress on the cranking system, do not attempt to crank open the umbrella from the lowest position. Open the umbrella canopy by (1) gripping the lever on the vertical slide handle and then slowly raise to a convenient height. Release the slide handle to lock into place. (2) Slowly turn the Crank Handle (EE) in a clockwise direction until the canopy is fully opened.

CAUTION: DO NOT open the umbrella counter-clockwise. It will not stay open and may close unexpectedly.

Canopy Adjustment

With the canopy fully opened, grip the lever on the vertical slide handle and raise or lower the canopy to the desired angle. Release the slide handle to lock into place.

Closing the Umbrella

To close the umbrella, turn the Crank Handle (EE) counter-clockwise.

CAUTION: When cranking the umbrella open, if you feel resistance and the canopy is not opening, do not force the Crank Handle (EE). Gently spread the umbrella ribs by hand and shake the fabric, then continue to crank open.

Horizontal Rotation

To rotate the Umbrella (A) canopy horizontally, place foot on the foot pedal of the Rotating Hub (C) and hands on the Umbrella (A) pole. Depress the pedal and rotate the umbrella in either direction to reach desired position. Release foot pedal to lock into place.

LED Lights

To operate LED lights, press the rocker switch located on the Umbrella (A) pole on or off.

Charging the Batteries

NOTE:

a) The Finial (M) contains two lithium batteries (2 x 2200mAh). Press the switch to the off position during daylight to allow the solar panel to charge the batteries. Charging time is dependent on the amount of sunlight, however, 8 hours is recommended.

b) The batteries can also be charged using the 100V-240V AC Adaptor (F) by plugging it into the Umbrella (A) pole as shown. Charging time is approximately 5-6 hours.

c) If the batteries are dead, the lights will operate with the AC Adaptor (F) plugged in. The red light on the AC Adaptor (F) indicates power is present.

d) Keep the umbrella unplugged and the AC Adaptor (F) stored in a dry location when not in use.

Care and Maintenance

Before using, clean the product completely with a soft, dry towel.

Wash with a mild solution of soap and water; rinse dry completely. Do not use strong detergent or abrasive cleaners.

Store the product in a cool, dry location away from sunlight.

Store the umbrella out of bad weather or high winds.

Troubleshooting

Problem: The umbrella lights only work properly when plugged in.

Possible Cause:

1. The solar panel, finial may not be properly installed. Remove the solar panel, finial and repeat Step 5, ensuring that the fixed barrel connectors line up correctly.
2. The batteries may be dead. Press the switch to the OFF position. With the solar panel, finial adaptor plugged in to charge the batteries. Allow approximately 8 hours of sunlight on the solar panel or 6 hours with the AC adaptor plugged in to charge the batteries.
3. If the lights do not work after troubleshooting steps 1 and 2, please contact customer service to further diagnose the problem.

Warranty

Umbrella frames are warranted for a period of one (1) year, fabric is warranted for a period of two (2) years.

Exceptions: Items used for commercial, contract or other non-residential purposes, display models, items purchased as is, or items damaged due to acts of nature, vandalism, misuse or improper assembly are not covered. Discoloration or fading of the finish or fabrics as a result of exposure to the elements, chemicals or spills are not covered. Tabletop glass breakage, corrosion or rusting of hardware and damages to frames or welds caused by improper assembly, misuse or natural causes are not covered. Wind Damage is not warranted, PLEASE LOWER Umbrella in bad weather.

Warranty to the original purchaser is non-transferable. All warranty claims require a dated sales receipt. Any replacement of warranted items will be in the original style and color, or a similar style and color if the original is unavailable or has been discontinued. We don't reimburse for transportation or delivery costs, or compensate the individual or any outside party for assembling or disassembling the product.

Replacement Parts List

For replacement parts, call our customer service department at 866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Sunday. You could also contact us at partsplus@lowes.com.

[Printed in China]