TECWERK Headlamp

Art.-Nr. 2000 877 184

Introduction

This manual provides instructions for the optimal use of your TECWERK Headlamp and helps to avoid damage. Please read the entire manual and keep it for future reference.

Safety Instructions

Do not use the device if the housing, plug, or cable is damaged. Contact an authorized specialist on site.
Do not open the device. Repair work and battery pack replacement must only be carried out by qualified electricians.
Carry out cleaning work only when the mains plug is disconnected. There is a risk of a short circuit. Repairs to the unit may only be carried out by authorized and trained personnel.
Protect the battery from heat, intense sunlight, fire, water, and moisture. There is a risk of explosion.
If the battery is damaged or not used properly, liquids may leak from the battery. Avoid contact with these. Leaking battery fluids can cause skin irritation or burns. If the liquid gets into your eyes, consult a doctor.
Do not place the lamp on the illuminated surface when it is switched on.

Product Warranty Instructions

The company ensures that products shipped from the factory meet relevant safety standards and technical requirements, displaying all functions under normal use and maintenance. If, within one year from the date of purchase, our maintenance personnel confirm that a failure is due to manufacturing processes or materials, the warranty is free.

This warranty covers any defects in material or workmanship, but does not include:

Product damage caused by incorrect use.
Product damage caused by incorrect installation.
Product damage caused by unauthorized customer modifications.
Natural disasters and man-made damage.

The company only performs product after-sales maintenance services with valid tickets and corresponding product warranty cards. Do not expose the product to moisture or water. Once the product is sold, no returns are accepted unless it is a quality problem.

Packaging materials, batteries, and electrical devices do not belong with normal household waste. As the owner, you are legally obligated to separate these materials from unsorted municipal waste and deliver them to the appropriate recycling collection site. Alternatively, you can also return them to the location where you purchased the product.

Technical Data

Feature	Specification
Light Source	CREE 6500K CRI>70 - Spot light
Luminous Power	approx. 800 lumens - Full power mode approx. 200 lumens - Low mode approx. 20 lumens - ECO mode
Operating Time	approx. 3 hrs - Full power mode approx. 6 hrs - Low mode approx. 60 hrs - ECO mode
Battery Specification	Li-Ion 3.7 V, 2600 mAh, 9.62Wh
Charging Time	approx. 4.5 hrs
Charging Input	USB-C / 5V 1A
Degree of Protection	IP 65, IK 07
Operating Temperature	-10 °C to +40 °C

Charging with an AC Power Supply Unit

Switch the lamp off during charging.
The LED indicator switches to green blinking during charging.
If charging is completed, the green LED will illuminate continuously.
Charge the headlamp for 4-5 hours before first use.
Fully charge the headlamp before storing it for a longer period.

Using the Switch Function

Operating mode as follows, press the switch:

One time to turn on the light to Full power mode.
Second time to switch the light to Low mode.
Third time to switch the light to ECO mode.
Fourth time to turn light off.

The headlamp is equipped with a smart memory function. If you stay more than 5 seconds in any mode, it will be memorized. The light will directly turn off when you press the light. The light will be turned to the memorized mode the next time you press the Power Button.

Declaration of Conformity

The NORDWEST Handel AG declares in sole responsibility that the article Headlamp, article number 2000 877 184 complies with the essential requirements of the following directives and regulations: 2011/65/EU, 2014/30/EU, VO (EU) 2023/1542.

A complete declaration of conformity can be downloaded from this internet address: https://download.nordwest.com/datasheets/

Manufacturer Information

NORDWEST Handel AG
Robert-Schuman-Straße 17
44263 Dortmund, Germany
Tel. +49 231 2222-3001
info@nordwest.com
www.nordwest-tecwerk.com

	TECWERK High Power LED Flashlight User Manual and Specifications Comprehensive user manual for the TECWERK High Power LED Flashlight (Art. No. 2000 877 188), including safety instructions, technical specifications, operating procedures, and warranty information.
	TECWERK LED Inspection Light User Manual Comprehensive user manual for the TECWERK LED Inspection Light (Art. No. 2000 877 190), covering safety instructions, product warranty, technical specifications, and operating procedures.
	TECWERK Machinist's Calipers User Manual Comprehensive user manual for TECWERK Machinist's Calipers, covering operation, features, troubleshooting, and technical specifications for 300mm, 500mm, and 800mm models.
	TECWERK LED Spotlight 50W User Manual and Safety Guide Comprehensive user manual for the TECWERK LED Spotlight 50W (Art.-No. 2000 873 341), covering installation, operation, safety precautions, maintenance, technical specifications, and disposal information. Includes multilingual safety guidance.
	TECWERK Spiralbohrer Schnittgeschwindigkeitsempfehlungen Detaillierte Empfehlungen für Schnittgeschwindigkeiten (Vc) und Kühlmethoden für TECWERK Kurzspiralbohrer bei verschiedenen Materialien wie Stahl, rostfreiem Stahl, Gusseisen und Nichteisenmetallen.
	Application Recommendations for Machining Materials Detailed table of application recommendations and cutting parameters for various materials including steels, cast iron, non-ferrous metals, and superalloys, specifying speed and cooling methods.
	Application Recommendations for Machining Materials Technical guide providing application recommendations for machining various materials, including steel, stainless steel, cast iron, non-ferrous metals, and tempered steel. Details recommended cutting speeds (Vc) and cooling methods for different material grades and hardness levels.
	TECWERK Machining Recommendations: Cutting Speeds and Cooling A technical data table from TECWERK providing recommended cutting speeds (Vc) and cooling methods for various materials, including different types of steel, cast iron, non-ferrous metals, and superalloys. The table specifies parameters based on tensile strength and material grades.