Pfister Mystique GT529-MD Single Control Kitchen Faucet

Warranty Information

Pfister Lifetime Mechanical & Finish Warranty

Pfister provides a Lifetime Mechanical & Finish Warranty covering the product's function and finish for as long as you own your home. Commercial applications have limited warranty durations.

Limited Warranties: Pfister warrants that the product will be free of defects in material and workmanship that would impair its intended use for as long as the original purchaser owns the home. For commercial applications, this warranty is limited to ten (10) years from the date of purchase.

Pfister also warrants against finish deterioration for as long as the original purchaser owns the home. For commercial applications, this finish warranty is limited to ten (10) years from the date of purchase (for products without Pforever finish).

Exclusive Remedy: Pfister will, at its option, repair or replace the defective part of the Product. This is the exclusive remedy.

Contacting Pfister for Warranty Service:

• Call: 1-800-Pfaucet (1-800-732-8238)
• Write: Consumer Service Department, Pfister Inc., 19701 DaVinci, Lake Forest, CA 92610
• Email: Visit www.Pfisterfaucets.com
• Notify the distributor from which the Product was purchased.

Proof of purchase may be required. Product may need to be returned for inspection.

Limitations and Exclusions: Pfister is not liable for incidental or consequential damages. This warranty does not cover damage resulting from improper maintenance, repair, cleaning, installation, misuse, abuse, alterations, accidents, or acts of God. Some states do not allow limitations on incidental or consequential damages, so these limitations may not apply to you.

Installation Instructions

WARNING: Read all instructions completely before proceeding. Pfister recommends calling a professional if you are uncertain about installing this product. This product should be installed in accordance with all local and state plumbing and building codes.

1. Shut Off Water Supply: Locate water supply inlets and shut off the water supply valves. If replacing an existing faucet, remove the old faucet and clean the sink surface.

• Plumber's putty
• Adjustable wrench
• Philips head screwdriver
• Pliers
• Flashlight
• Cloth

Your installation may require new supply lines and/or shut-off valves or other additional tools.

Ensure all parts are included:

• A Faucet Body
• B Spray Head
• C Pull-Out Hose
• D Soap Dispenser
• E Soap Dispenser Head
• F Deckplate
• G Putty Plate
• H Wing Nuts (2x)
• J Metal Washer
• K Locknut
• L Weight
• M Quick Connector
• N Mounting Ring
• P Putty Ring
• Q Inlet Connectors (2x)

If any items are missing, contact Pfister Consumer Services at 1-800-Pfaucet (1-800-732-8238).

This product covers two different installations:

• Option 1: 4 Hole With Deckplate Installation: Go To Step 6
• Option 2: 2 Hole With Single Post Installation: Go To Step 8

1. 6. Installing Deckplate: Ensure Plastic Putty Plate (6A) is on Deckplate (6B). Place plumber's putty in the bottom groove along the outer edge of the Putty Plate (6A). Install Deckplate (6B) over the three holes in your sink.
2. 7. Securing Deckplate: From underneath the sink, hand tighten Wing Nuts (7A). Caution: do not over-tighten. Remove any excess putty from around the outside edge of Putty Plate (7B).
3. 9. Body Installation: Retract Pullout Hose (9A) up through Faucet Body (9B) until the pullout hose fitting is flush with the bottom of Mounting Shank (9C). Insert Faucet Supply Tubes (9D) and Mounting Shank (9C) through the hole in Deck Plate (9F) or Mounting Ring (9G). The handle (9E) can be oriented left or right. Ensure Protective Caps (9H) are in place. Note: Do not feed the pullout Hose (9A) back down through the spout yet.
4. 10. Securing Spout Body: From underneath the sink, place Washer (10A) and Locknut (10B) over Pull-Out Hose (10C) and Supply Tubes (10D). Thread loosely onto Mounting Shank (10E). Ensure Handle (10F) is properly aligned to the sink. Tighten faucet firmly to the sink.
5. 11. Quick Connect & Weight Attachment: Insert the end of the Pull-Out Hose (11A) into the Weight (11B). Screw Quick Connector (11C) to the free end of Pull-Out Hose (11A).
6. 12. Pull-Out Hose Attachment: From underneath the sink, remove Protective Cap (12E). Push Quick Connector (12A) on the Pull-Out Hose (12B) firmly upward onto the Receiving Tube (12C) until unable to push further. Pull down on the Quick Connector (12A). If the housing and inner collect separate slightly but do not pull off, the Receiving Tube (12C) quick connect is secure.
7. 13. Soap Dispenser Installation: From above the sink, insert threaded Shank (13A) of soap dispenser body through Foam Gasket (13B) and sink hole. From below the sink, tighten Nut (13C) and thread Soap Bottle (13D) onto Shank (13A).
8. 14. Soap Dispenser Head Installation: Pour liquid soap (not included) into the Soap Dispenser Body (14A). Insert Pump Mechanism (14B) into Soap Dispenser Body (14A). Install Dispenser Head (14C) by pushing firmly onto Pump Mechanism (14B).
9. 15. Water Supply Connections: Water Supply Lines are not included. Consult manufacturer instructions. CAUTION: Incorrect application of supply lines and fittings may result in failure or leaks.
   • A. Thread Inlet Connectors (15A) into Water Supply Lines (15B).
   • B. Remove Protective Cap (15F). Gently separate hot and cold Faucet Inlets (15C), approximately 1 in. (26 mm) apart. Connect Water Supply Lines (15B) onto Faucet Inlets (15C). Hot water supply line goes to hot inlet fitting indicated by red tag.

1. 8. Installing Mounting Ring: Place Mounting Ring (8A) over Plastic Seal (8B) and sink hole. Align Mounting Ring (8A) to the center of the sink hole. Place a bead of plumber's putty in the bottom groove along the outer edge of Plastic Ring (8B).
2. 9. Body Installation: Retract Pullout Hose (9A) up through Faucet Body (9B) until the pullout hose fitting is flush with the bottom of Mounting Shank (9C). Insert Faucet Supply Tubes (9D) and Mounting Shank (9C) through the hole in Deck Plate (9F) or Mounting Ring (9G). The handle (9E) can be oriented left or right. Ensure Protective Caps (9H) are in place. Note: Do not feed the pullout Hose (9A) back down through the spout yet.
3. 10. Securing Spout Body: From underneath the sink, place Washer (10A) and Locknut (10B) over Pull-Out Hose (10C) and Supply Tubes (10D). Thread loosely onto Mounting Shank (10E). Ensure Handle (10F) is properly aligned to the sink. Tighten faucet firmly to the sink.
4. 11. Quick Connect & Weight Attachment: Insert the end of the Pull-Out Hose (11A) into the Weight (11B). Screw Quick Connector (11C) to the free end of Pull-Out Hose (11A).
5. 12. Pull-Out Hose Attachment: From underneath the sink, remove Protective Cap (12E). Push Quick Connector (12A) on the Pull-Out Hose (12B) firmly upward onto the Receiving Tube (12C) until unable to push further. Pull down on the Quick Connector (12A). If the housing and inner collect separate slightly but do not pull off, the Receiving Tube (12C) quick connect is secure.
6. 13. Soap Dispenser Installation: From above the sink, insert threaded Shank (13A) of soap dispenser body through Foam Gasket (13B) and sink hole. From below the sink, tighten Nut (13C) and thread Soap Bottle (13D) onto Shank (13A).
7. 14. Soap Dispenser Head Installation: Pour liquid soap (not included) into the Soap Dispenser Body (14A). Insert Pump Mechanism (14B) into Soap Dispenser Body (14A). Install Dispenser Head (14C) by pushing firmly onto Pump Mechanism (14B).
8. 15. Water Supply Connections: Water Supply Lines are not included. Consult manufacturer instructions. CAUTION: Incorrect application of supply lines and fittings may result in failure or leaks.
   • A. Thread Inlet Connectors (15A) into Water Supply Lines (15B).
   • B. Remove Protective Cap (15F). Gently separate hot and cold Faucet Inlets (15C), approximately 1 in. (26 mm) apart. Connect Water Supply Lines (15B) onto Faucet Inlets (15C). Hot water supply line goes to hot inlet fitting indicated by red tag.

1. 16. Unit Start Up: Turn on hot and cold water supplies, and check for leaks above and below the sink.

Faucet Functions

• 17. Spout Function: The Spout (17A) can be rotated around the Faucet Body in any direction.
• 18. Valve Function: By rotating the Lever Handle (18A) away from the Faucet Body (18B), the valve is activated allowing water to flow. The water flow increases by continuing to rotate the Lever Handle (18A). By rotating the Lever Handle towards you, the water temperature decreases to cold flow only. By rotating the Lever Handle away from you, the water temperature increases to hot flow only. Note: Flush faucet before turning on valve (see step 23).
• 19. Pull-Out Operation: The Pull-Out Hose (19A) can be pulled forward to spray water in any direction.
• 20. Spray Operation: By activating the valve, water flows in a regular stream. To activate spray mode, press Button (20A) behind Spray Head (20C). Pressing Button (20B) changes the spray pattern between spray and stream. Holding Button (20B) pauses water flow.
• 21. Soap Dispenser Operation: To activate Soap Dispenser (21A), press Dispenser Head (21B) to dispense liquid soap.

Maintenance & Care

• 22. Spray Head Removal: To prevent damage from debris, remove the spray head (22A). To remove, hold metal Hose Fitting (22B) and turn Spray Head (22A) counterclockwise.
• 23. Flushing: Turn on Valve Lever Handle (23A). Run water for one minute. Repeat in hot and cold positions. Reassemble the Spray Head (23B) to the Pull-Out Hose (23C) by turning clockwise. Caution: Do not over tighten.
• 24. Aerator Cleaning: Unscrew Aerator Housing (24A) from Spray Head (24B). Remove Aerator Seal (24C) and Aerator Cartridge (24D) from Aerator Housing (24A). Clean Cartridge (24D) and Housing (24A). Reassemble by reversing steps.
• 25. Pull-Out Hose Removal: To remove the quick connect attachment, push down on Quick Connector button (25B). Then pull downward on Quick Connector (25A) until Tube (25C) is free.
• 26. Cartridge Replacement: Turn off water supplies and relieve pressure. Using a 3/32" Hex wrench, loosen Set Screw (26A) and remove Handle (26B). Remove Dome Cap (26C) by unscrewing counterclockwise. Unscrew Retainer Ring (26D) and carefully remove Cartridge (26E) by pulling it straight up. Reassemble by reversing steps.

• Replacement parts may be available at the store where you purchased your faucet.
• When replacement parts are not available, contact Pfister Consumer Service.
• Always turn off water and relieve pressure before working on your faucet.

For all Handles and decorative finishes, use only a soft damp cloth to clean and shine. Use of polish, detergents, abrasive cleaners, organic solvents, or acid may cause damage. Use of anything other than a soft damp cloth will nullify the warranty.

Special Trim: Trim products containing porcelain or similar substances are not acceptable for public areas or commercial use. Installation of such trim is at the user's risk.

Contact Information

For Toll-Free Pfaucet information, call 1-800-PFAUCET (1-800-732-8238) or visit www.pfisterfaucets.com.

• Installation Support
• Care and Warranty Information

Parts Diagram

The parts diagram provides a visual breakdown of the faucet components with corresponding part numbers and descriptions in English, Spanish, and French.

Key components include:

• Faucet Body (931-002)
• Spray Head (951-092C, 951-092B)
• Hose (941-246*)
• Deckplate Assembly (962-029)
• Mounting Hardware (950-004, 970-075, 941-085*, 950-508*, 951-260, 962-074, 974-074, 971-130, 940-331*)
• Soap Dispenser Components (14A, 14B, 14C)
• Water Supply Lines (15A, 15B, 15C)
• Cartridge (26E)

Finish designations are indicated by letters: A for Polished Chrome, S for Stainless Steel.