APX ERIG INSTRUCTION MANUAL

KIT INCLUDES:

• 1x APX™ eRig main body with pivoting detachable atomizer connection
• 1x Coil-less quartz cup atomizer
• 1x Removable airpath tube
• 1x Glass mouthpiece
• 1x Base jar
• 1x Downstem
• 1x Glass coil collar
• 1x Glass carb cap
• 1x Silicone carb cap tether
• 2x Quartz terp pearls (6mm diameter)
• 1x Terp Tong
• 1x Stainless steel dab tool
• 1x USB-C charging cord
• 2x Replacement O-rings
• 4x Alcohol swabs
• 1x Cleaning brush
• 1x Pulsar® silicone mat

TECHNICAL SPECIFICATIONS:

• Dimensions: 5.39x4.13x10.62 in (137x105x270mm)
• Battery Capacity: 3200mAh
• Charging: 5V/2.5A
• Charging Time: 90 minutes
• Temperature Settings: 482°F to 842°F (250 to 450°C)
• Heating Coil Resistance: 0.7Ω
• Sesh Mode Time: 40 seconds after reaching set temperature
• Auto Shut-Off: After 5 minutes of inactivity

HOW TO USE YOUR NEW DEVICE:

1. Plug the APX™ eRig into an appropriate wall charger using the provided cable. The light above the charging port will flash red (0%-30%), yellow (30%-64%), and green (65%-100%). The light turns solid green when fully charged.
2. Assemble the device: Attach the mouthpiece to the main body with a slight twist. Fill the base jar with water to the fill line, then gently push the downstem into the bottom of the main body. Push the main body down onto the base jar with a slight twist. Screw on the atomizer, then place the glass collar on the atomizer connection. Finally, place the carb cap tether on the collar and insert the carb cap into the small hole at the end of the tether.
3. Click the power button 5 times to turn the APX eRig on or off. The light around the power button indicates the current temperature setting, and the lower LED flashes green in the base jar when on. The lower LED flashes white when off.
4. Click the power button 3 times to change the temperature setting:
   • 482°F (250°C) - Blue
   • 572°F (300°C) - Cyan
   • 662°F (350°C) - Green
   • 752°F (400°C) - Purple
   • 842°F (450°C) - Red
5. Load the atomizer with concentrate, being careful not to overfill. Press and hold the power button to heat. Release to stop. The light around the power button pulses during heating, and the lower LED cycles through colors. Both lights turn solid when the temperature is reached. Haptic feedback indicates when the temperature is reached and the heating cycle is finished.
6. Click the power button twice to start Sesh Mode. Click twice again to stop. The light around the power button pulses during heating, and the lower LED cycles through colors. Both lights turn solid when the temperature is reached. Haptic feedback indicates when the temperature is reached and the heating cycle is finished.
7. The device enters standby mode for 5 minutes before powering off after a heating cycle.

CHARGING YOUR DEVICE:

• 100-65%: Green
• 64-30%: Yellow
• 30-0%: Red

Only charge using Pulsar® brand chargers and accessories. Use a charger with an output of 5V/2.5A or lower. The light above the charging port indicates battery level. When the device is on, the battery level is shown. When off, press the power button once to check the battery level.

PULSAR® PRO TIPS!

Before your session, pivot the APX™ eRig main body so the mouthpiece points towards you for comfort and optimal atomizer position. The atomizer should remain vertical for even oil distribution across the coil surface.

Diagram Description: An illustration shows how to hold the APX eRig. One hand holds the atomizer stable, while the other hand holds the body and mouthpiece. The body hand is used to pivot the mouthpiece towards the user, ensuring the atomizer remains vertical.

TERP BEADS

Use one terp bead in the atomizer to enhance your session. Terp beads retain heat, so use caution when removing them while the atomizer is hot. Wait until the atomizer is cool to the touch and use the provided terp tong to remove the bead.

CLEANING INSTRUCTIONS:

Recommended cleaning supplies: cotton-tipped swabs and isopropyl alcohol (91% or higher).

COIL MAINTENANCE

Wipe the quartz atomizer with a cotton-tipped swab after each session for optimal performance. For lingering build-up, dip a cotton-tipped swab in isopropyl alcohol before wiping the atomizer. Allow the atomizer to cool down before cleaning and wipe up any residual solvent.

GLASS

Disassemble all glass parts before cleaning. Soak glass in isopropyl alcohol or use an alcohol wipe to remove build-up. Rinse with cold water and air dry before reassembly.

AIR PATH

With the glass mouthpiece removed, pull the metal air path out of the silicone housing and soak in isopropyl alcohol. Use the included cleaning brush to remove clogs. Rinse with cold water and air dry. For deeper cleaning, use a cotton-tipped swab and alcohol to clean the silicone housing. Allow all parts to air dry before reassembly.

ATOMIZER CONNECTION

To clean this section, remove the glass collar and coil from the 510 connection. Use a cotton-tipped swab and isopropyl alcohol to clean around the 510 connection and in the vapor path. To clean the lower air path, pull out the silicone plug. Allow parts to air dry before reassembly.

WARNINGS:

Do not expose to extreme temperatures or direct sunlight. Do not drop the device or accessories. Do not drop or submerge in any liquid. Do not modify the electronics. This device is intended for adults only; do not sell or provide to minors. Keep all parts, concentrates, herbs, and liquids away from children and pets. This is not a medical device and is not intended to diagnose, treat, mitigate, cure, or prevent any ailment, disease, or other conditions. Consult a physician before use, especially if you suffer from heart disease or any other medical condition, or if you are pregnant or breastfeeding. Failure to follow these instructions could result in product damage, property damage, personal injury, and may void the warranty.

Diagram of APX eRig Components:

The diagram illustrates the APX eRig with the following labeled components:

• USB-C CHARGE PORT
• BATTERY LEVEL LIGHT
• BOROSILICATE MOUTHPIECE
• BOROSILICATE SPINNER CARB CAP
• CARB CAP TETHER
• ATOMIZER
• BOROSILICATE COLLAR
• ATOMIZER MANIFOLD (DETACHABLE, MAGNETIC, PIVOTING)
• CONTROL BUTTON + TEMPERATURE LIGHT + DAB TIMER
• SHOWERHEAD PERC DOWNSTEM
• BOROSILICATE BASE JAR

The device is 10.5" TALL / 3200MAH.