Fanatec Podium Steering Wheel BMW M4 GT3

A. Package Content

• 1x Podium Steering Wheel BMW M4 GT3
• 1x QR2 Pro Wheel-Side (Pre-installed)
• 1x QR2 USB Update Cable (~80 cm)
• 1x Button Caps

B. Getting Started

Follow these steps to get started:

1. Connect the steering wheel to your PC or console.
2. Download and install the latest Fanatec drivers from fanatec.com/driver.
3. Visit fanatec.com/app for the Fanatec App.
4. For detailed video manuals, visit fanatec.com/QR/P-BMW-GT3.
5. Refer to the full manual at fanatec.com/manuals.

C. Firmware Update

Instructions:

1. Connect the steering wheel to your PC using the QR2 USB Update Cable.
2. Run the Fanatec Firmware Updater application.
3. Select the correct firmware and click 'Flash Firmware' [Flash Firmware].
4. Wait for the update to complete.

Note: Firmware updates may depend on your Wheel Base model.

D. Centre Calibration

To calibrate the steering wheel's center position:

1. Enter the Tuning Menu [Tuning Menu] on your wheel base.
2. Navigate [Navigate] to the calibration option.
3. Follow the on-screen prompts, typically involving turning the wheel fully left, then fully right, and centering it.
4. Press the 'Enter' [Enter] button to confirm.

Note: Calibration steps might vary slightly based on the connected wheel base.

E. Modes

The steering wheel supports various modes for different functionalities. Refer to the full manual for detailed explanations of each mode.

F. Shifter Calibration

Calibrate your shifters for optimal performance:

1. Access the shifter calibration menu.
2. Follow the on-screen instructions to perform the calibration for all gears. This usually involves engaging each gear sequentially.

G. Tuning Options

Access the Tuning Menu [Tuning Menu] to adjust various settings such as force feedback, button assignments, and LED modes.

Navigation: Use the directional buttons and the 'Enter' [Enter] button to navigate and select options.

Exit: Press the 'Exit' [Exit] button to leave the Tuning Menu [Tuning Menu].

H. Rev LED Mode

Customize the behavior and appearance of the Rev LED indicators. Options typically include activating/deactivating [Activate/Deactivate] certain modes or changing color patterns.

I. Paddle Adjustments

The shifter and clutch paddles can be adjusted for personalized feel.

Shifter Paddles: Adjust the position using the 2.5 mm bolts. Torque specification: 1.5 Nm.

Clutch Paddles: Adjust the position using the 2.5 mm bolts. Bolts are self-locking.

Important: Do not remove or replace the adjusting bolts ⚠️. Ensure bolts are properly tightened.

Note: Adjustment tools (e.g., 2.5 mm Allen key) are not included [Not included].

J. Button Caps

Apply the included button caps to customize button labels and appearance. Press firmly until they click into place [Click!].

K. Button Mapping

Customize button assignments for PC and PlayStation® platforms. The following table outlines common assignments and available functions:

Note: *GSB = Game-Specific Button. Refer to the video manual for more details.

L. Support

For technical support, FAQs, and more information, visit:

• Fanatec Support: fanatec.com/support/faq
• Product Page: fanatec.com/QR/P-BMW-GT3
• Fanatec App: fanatec.com/app

Warranty Information

The product warranty is provided by Endor AG. Refer to the included warranty sheet and the terms & conditions of Endor AG on fanatec.com.

China RoHS 2 Compliance

China RoHS 2 refers to the Ministry of Industry and Information Technology Order No. 32, effective July 1, 2016, titled Management Methods for the Restriction of Use of Hazardous Substances in Electrical and Electronic Products. To comply with China RoHS 2, the product's Environmental Protection Use Period (EPUP) is determined to be 10 years in accordance with the Marking for the Restricted Use of Hazardous Substances in Electronic Electrical Products, SJT 11364-2014.

The following table indicates the presence of hazardous substances:

Legend:

• 'O' indicates that the hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement of GB/T 26572.
• 'X' indicates that the hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement of GB/T 26572.

FCC Compliance

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) must accept any interference received, including interference that may cause undesired operation.

Note: This device was tested and approved for Class B digital devices according to part 15 of FCC rules, ensuring adequate protection against harmful interference in residential areas. However, a warranty for the non-recurrence of interference is not assumed. Do not modify the device differently than explicitly described in the product manual.

Legal Information

The BMW logo, word mark, and model designation are trademarks of BMW AG and are used under license.

Fanatec® is a registered trademark of Endor AG.

Designed and developed by Endor AG in Germany.

Manufactured and distributed by:

Endor AG, E.ON-Allee 3, 84036 Landshut, Germany

Importers:

Endor America LLC, 8200 Wilshire Blvd. Suite 200, Beverly Hills CA 90211, USA

Endor Australia Pty Ltd, 3 Staley Street, California Gully, Vic, 3556, Australia

Endor Japan Kabushikigaisya, E5001 3-13-1, Harumi Cyuo-ku, Tokyo-to, Tokyo 104-0053, Japan

Contact:

Website: www.fanatec.com, www.endor.ag

Customer Service Numbers:

EU/US/CANADA/AUSTRALIA: 00800 0 FANATEC or +49 (871) 9221-122

JAPAN: +81 306 7172-719