PARKSIDE LED Light PALC 3 C1

Introduction

Congratulations on the purchase of your new PARKSIDE product. This operation and safety manual contains important information regarding safety, use, and disposal. Please familiarize yourself with all instructions before using the product.

Intended Use

This product is intended for normal, private use in dry indoor locations such as storerooms or corridors. It is not intended for commercial use or as household room illumination.

Parts Description

For HG11935A:

• 1 Release button
• 2 Handle
• 3 Lamp head
• 4 Front spotlight
• 5 Switch
• 6 Magnet
• 7 Strip light
• 8 Plastic strip
• 9 Battery compartment cover
• 10 Battery compartment
• 11 Screw

For HG11935B:

• 1 Front spotlight
• 2 Strip light
• 3 Switch
• 4 Handle
• 5 Magnetic base
• 6 Magnet
• 7 Hook
• 8 Battery compartment cover
• 9 Plastic strip
• 10 Battery compartment
• 11 Screw

Technical Data

Scope of Delivery

• 1 LED light
• 3 Batteries (pre-installed)
• 1 Set of instructions for use

Safety Notices

General Safety Instructions

• Keep out of reach of children.
• Do not dispose of in fire.
• Do not insert incorrectly.
• Do not deform/damage.
• Do not use if damaged.
• Protect from moisture and humidity. Never immerse in water or other liquids.
• LEDs are not replaceable. If LEDs fail, the entire product must be replaced.
• Do not look directly into the light, as it may be harmful to the eye.

Safety Instructions for Batteries/Rechargeable Batteries

DANGER TO LIFE! ⚠️ Keep batteries/rechargeable batteries out of reach of children. If accidentally swallowed, seek immediate medical attention. Swallowing may lead to burns, perforation of soft tissue, and death. Severe burns can occur within 2 hours of ingestion.

DANGER OF EXPLOSION! ? Never recharge non-rechargeable batteries. Do not short-circuit or open batteries/rechargeable batteries. Overheating, fire, or bursting can result. Never throw batteries/rechargeable batteries into fire or water. Do not exert mechanical loads on batteries/rechargeable batteries.

Risk of leakage: Avoid extreme environmental conditions. If batteries/rechargeable batteries have leaked, avoid contact with skin, eyes, and mucous membranes with the chemicals! Flush affected areas immediately with fresh water and seek medical attention! WEAR PROTECTIVE GLOVES! ? Leaked or damaged batteries/rechargeable batteries can cause burns on contact with the skin. Wear suitable protective gloves.

Risk of damage: Use only the specified type of battery/rechargeable battery. Insert batteries/rechargeable batteries according to polarity marks (+/-). Clean contacts before inserting. Remove exhausted batteries immediately.

Before Use

Remove all packaging materials from the product.

For HG11935A: Extend the strip light (7) from the handle (2) by the lamp head (3). Loosen screw (11) and remove the plastic strip (8) from the battery compartment cover (9).

For HG11935B: Loosen screw (11) and remove the plastic strip (9) from the battery compartment cover (8).

Your product is now ready to use.

Functions

For HG11935A:

The product has two light functions (front spotlight and strip light) that can be used simultaneously.

• Press switch (5) to turn on the front spotlight (4) at high brightness.
• Press switch (5) again to dim the front spotlight (4).
• Press switch (5) again to turn off the front spotlight (4).
• Extend the strip light (7) from the handle (2) to turn it on. Push it back into the handle (2) to turn it off.

NOTE: Only operate the strip light (7) when it is completely extended. Otherwise, there is a risk of overheating!

For HG11935B:

The product has two light functions, activated by the switch (3).

• Press switch (3) to turn on the strip light (2).
• Press switch (3) again: The strip light (2) turns off, and the front spotlight (1) turns on simultaneously.
• Press switch (3) again to turn off the product.

Mounting

The product has two magnets (6) for attachment to magnetisable surfaces.

Aligning the lamp head: Push release button (1) and flip lamp head (3) out of the locking device. The lamp head can be tilted up to 90° for targeted lighting.

For HG11935B: The product can be attached using the hook (7). Ensure the hanging location is suitable for the product's weight. Alternatively, use the magnets (6) on a magnetic surface. The product can be tilted up to 180° on the magnetic base (5). CAUTION: Be mindful of your hands when turning the magnetic base (5) to avoid pinching fingers.

Inserting/Replacing Batteries

If brightness decreases, batteries need replacement. Follow these steps:

For HG11935A: Pull strip light (7) from handle (2). Open battery compartment cover (9) by loosening screw (11). Insert three new AAA batteries, observing polarity. Close cover (9) and tighten screw (11).

For HG11935B: Open battery compartment cover (8) on the back by loosening screw (11). Insert three new AAA batteries, observing polarity. Close cover (8) and tighten screw (11).

Remove batteries if the product will not be used for an extended period.

Cleaning and Care

Clean the product only on the outside with a soft, dry cloth. Never use liquids or detergents, as they can damage the product.

Disposal

Packaging is made of recyclable materials. Dispose of it at local recycling facilities.

When the product reaches the end of its useful life, do not dispose of it in household waste. Recycle it responsibly. Consult your local authority for disposal information.

Faulty or used batteries/rechargeable batteries must be recycled. Return them to available collection points.

Environmental damage through incorrect disposal of batteries/rechargeable batteries! Batteries may contain toxic heavy metals and are subject to hazardous waste treatment. Dispose of used batteries at a local collection point.

Warranty

PARKSIDE products are manufactured to strict quality guidelines. This product has a 3-year warranty from the date of purchase. Keep the original sales receipt as proof of purchase. The warranty covers material and manufacturing defects but excludes normal wear and tear, consumables (e.g., batteries), and damage from improper use or maintenance. Warranty is void if the product is damaged or misused.

Warranty Claim Procedure

For prompt processing of warranty claims:

• Have your receipt and item number (IAN 459048_2401) ready.
• Contact the service department by phone or email.
• Send the defective product postage-free to the provided service address, including proof of purchase and a description of the defect and when it occurred.

You can download manuals and further information at parkside-diy.com.

Service

For service inquiries, please visit parkside-diy.com or contact the relevant service center for your region.

Service Great Britain: Tel.: 0800 0569216, E-Mail: owim@lidl.co.uk

Service Deutschland: Tel.: 0800 5435 111, E-Mail: owim@lidl.de

Service Österreich: Tel.: 0800 292726, E-Mail: owim@lidl.at

Service Schweiz: Tel.: 0800562153, E-Mail: owim@lidl.ch

Service Slovenija: Tel.: 00386 (0) 80 080 917, E-Mail: infofon@lidl.si

Service Slovakia: Tel.: 0800 008158, E-Mail: owim@lidl.sk

Service Czech Republic: Tel.: 800600632, E-Mail: owim@lidl.cz

Manufacturer: OWIM GmbH & Co. KG, Stiftsbergstraße 1, 74167 Neckarsulm, GERMANY

Version: 06/2024