Resistex Noclip LED Lighting Fixture

Safety and Maintenance Instructions

Safety Notes

• Never work on the luminaire when it is live (under voltage).
• Installation must be performed by a professional installer in compliance with current electrical installation standards and regulations.
• Risk of electrostatic discharges (ESD Norm). Handle with necessary precautions.
• Please observe the notes and steps described in the mounting instructions.

Maintenance Instructions

• Do not use chemical or abrasive products to clean the luminaire.
• Keep these instructions for dismantling or future maintenance.
• Additional information about RESISTEX luminaires is available on the website: www.resistex-sa.com.
• RESISTEX cannot be held responsible for any misuse of the product.

Installation Steps

Follow these steps for the correct installation of the Resistex Noclip fixture.

1. Step 1: Access Fixture

   Open or release a part of the fixture by pressing the indicated mechanism [Push].

   [Diagram: Shows a close-up of a fixture component being opened via a push-button mechanism.]

2. Step 2: Cable Connection Preparation

   Prepare the power cable (type HO5RN-F or U-1000 R2V) for connection.

   [Diagram: Shows the end of a flexible cable being prepared for connection.]

3. Step 3: Select Connection Type

   Choose the appropriate connection module based on your system:

   • ON/OFF HF: For standard on/off or high-frequency control.
   • BP: For basic power or specific control protocols.
   • DALI: For Digital Addressable Lighting Interface control.

   [Diagram: Illustrates three distinct connection modules labeled ON/OFF HF, BP, and DALI, showing terminal designations like L, N, E, DA/N, DA/L.]

4. Step 4: Wire Connections

   Connect the wires from the power cable to the corresponding terminals on the fixture's internal driver/module. Ensure correct polarity (L - Live, N - Neutral, E - Earth).

   [Diagram: Shows wires being inserted into terminal blocks labeled L, N, E, DA/N, DA/L.]

5. Step 5: Secure Cable Entry

   Feed the connected cable through the designated entry point and secure it to prevent strain on the connections.

   [Diagram: Shows the power cable being routed through an entry gland and secured.]

6. Step 6: Mount Fixture Base

   Attach the fixture's base plate to the mounting surface (ceiling or wall) using screws (Ø6) and appropriate wall plugs if necessary.

   [Diagram: Shows a base plate being fixed to a surface with screws.]

7. Step 7: Attach Fixture Body

   Mount the main body of the Noclip fixture onto the secured base plate. This may involve a click-in mechanism or further securing screws.

   [Diagram: Shows the main luminaire body being attached to the base plate.]

8. Step 8: Final Assembly and Dimensions

   Ensure the fixture is securely assembled. The length (L) of the luminaire affects the required cable length for installation:

   • For 1200mm luminaires: Recommended cable length is 700mm to 1000mm.
   • For 1500mm luminaires: Recommended cable length is 900mm to 1200mm.

   [Diagram: Shows the fully assembled fixture and illustrates the length (L) and corresponding cable length requirements for different fixture sizes.]

Company Information

RESISTEX EXPLOITATION

11 Quai de la Banquière CS 80010, 06730 Saint-André-de-la-Roche - France

Tel: 04 93 276 276 - Fax: 04 93 276 280 - Email: contact@resistex-sa.com

APE 2740Z - Siret 487 593 477 00010 - SAS CAPITAL 649979 € - T.V.A. F.R. 73 487 593 477

Certifications and Standards

This product complies with the following standards:

• RoHS Compliant
• IP65 Rated (Ingress Protection)
• IK10 Rated (Impact Protection)
• High Color Rendering Index (CRI >80)
• 5 Years Warranty
• CE Marked