Bar Maid Commercial Electric Glass Polisher

Important for Future Reference

Please complete the following information and retain this manual for the life of the equipment. For Warranty Service and/or parts, this information is required.

[California Warning]: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Introduction

Congratulations on your WINCO® equipment purchase! Please take time to carefully read through this manual to ensure the equipment is operated and maintained properly, to ensure the best possible performance from the product for many years.

WINCO will not accept liability if:

• The instructions in this manual have not been followed correctly.
• Non-authorized personnel have tampered with the equipment.
• Non-original spare parts are used.
• The equipment has not been handled and cleaned correctly.
• There is any use damage to the unit.

Immediately Inspect for Shipping Damage

All containers should be examined for damage before and during unloading. The freight carrier has assumed responsibility for its safe transit and delivery. If equipment is received damaged, either apparent or concealed, a claim must be made with the delivering carrier.

A. Apparent damage or loss must be noted on the freight bill at the time of delivery. It must then be signed by the carrier representative (Driver). If this is not done, the carrier may refuse the claim. The carrier can supply the necessary forms.

B. If concealed damage or loss is not apparent until after equipment is uncrated, a request for inspection must be made to the carrier within 15 days. The carrier should arrange an inspection. Be certain to keep all contents and packaging material.

Specifications

The following table details the specifications for the Bar Maid Commercial Electric Glass Polishers.

Package Contents & Unpacking

Package Contents

• Glass Polisher Unit
• GP-100: (4) Polishing Brushes and (1) Short Polishing Brush
• GP-3MINI: (2) Polishing Brushes and (1) Short Polishing Brush

WINCO® prides itself on quality and service, ensuring that at the time of packing, all products are supplied fully functional and free of damage. Should you find any damage as a result of freight, please contact your WINCO dealer immediately.

Unpacking the Equipment

DISPOSE OF ALL PACKAGING MATERIALS IN AN ENVIRONMENTALLY RESPONSIBLE MANNER.

1. Remove all packing materials and tape, as well as any protective plastic and cardboard, from the unit.
2. Clean any glue residue left over from the plastic or tape.
3. Place the unit in the desired position and height.

SAVE THE ORIGINAL BOX AND PACKAGING FOR USE IN PACKAGING AND SHIPPING THE EQUIPMENT IF SERVICES ARE NEEDED.

Thoroughly read, understand, and follow these instructions before installation and use.

Please keep this manual in a safe place for future use!

NOTE: Please remember that this manual and the warning labels do not replace the need to be alert, to properly train and supervise operators, and to use common sense when using this equipment.

Safety Precautions

Before installing and operating this equipment, ensure everyone involved in its operation is fully trained and aware of all precautions. Accidents and problems can result from a failure to follow fundamental rules and precautions.

• A WINCO® Approved Recommended Qualified Service Technician should carry out repairs if necessary.
• Do not remove any components or service panels on this product.
• Before handling, allow the equipment to cool after use.
• Before cleaning, switch off power and disconnect power cord from the outlet.
• Do not immerse unit in water or use hose to clean.
• If the power cord is damaged, it must be replaced by a WINCO® Approved Recommended Qualified Service Technician in order to avoid a hazard.
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
• Contact your local gas supplier and ask for instructions in the event the user smells gas. This information should be posted in a prominent location.

Installation

These instructions should be followed at all times. Failure to follow these instructions could result in injury to yourself and others.

TO REDUCE RISK OF INJURY OR DAMAGE TO THE UNIT:

1. Read this manual thoroughly before installation and operation. DO NOT proceed with installation and operation if you have any questions or do not understand anything in this manual. Contact your representative or the manufacturer first.
2. Remove the equipment from the packaging. Be certain that all protective plastics and residues are thoroughly cleaned from its surface.
3. Place your equipment on a firm level surface. Local standards and regulations should be consulted in order to abide by standards set in relation to positioning, spacing, and ventilation. Bar Maid recommends no less than 4" for a ventilation gap around the perimeter of this unit.
4. Proper connections and power supply are essential for efficient performance. Supply the appropriate power and connect to source; the equipment is now ready to turn on and operate. (For power supply please see technical specification on page 1).
5. The installation of the unit must conform to the NATIONAL ELECTRIC CODE, ALL LOCAL ELECTRIC CODES AND ORDINANCES, AND ALL THE LOCAL ELECTRICAL COMPANY RULES AND REGULATIONS. Additionally, we recommend a 4" spacing surrounding the unit in order to provide adequate ventilation.

[Warning] Fire Hazard:

Correct installation precautions, procedures and regulations must be followed. Operation and safety training is necessary for all users of this equipment. The equipment must be installed by qualified personnel only. Correct installation precautions, procedures and regulations must be followed in order to reduce the risk of fire. Hood and fire suppression systems must be maintained per manufacturer's guidelines. Only qualified and trained personnel are to use this equipment.

[Caution] Do not position or operate near combustible materials/flammable objects.

[Warning] Electrical Shock Hazard:

Keep water and other liquids from entering the inside of the unit. Liquid inside the unit could cause an electrical shock. Do not spray water or cleaning products. Liquid could contact the electrical components and cause a short circuit or an electrical shock. Do not use unit if power cord is damaged or has been modified.

Proper Grounding

USE A GROUNDED OUTLET. DO NOT ADD AN ADAPTOR TO THE PLUG.

This machine is provided with a three-pronged grounding plug. The outlet to which this plug is connected must be properly grounded. If the receptacle is not the proper grounding type, contact an electrician.

DO NOT, under any circumstances, cut or remove the third ground prong from the power cord or use any adapter plug.

Preparation

1. Install the machine on a flat surface and make sure the machine is upright and stable.
2. Attach air blower onto the base with screw provided, make sure the opening is centered.
3. GP-100: Insert short brush onto center post of the base and remaining brushes onto outer posts. GP-3MINI: Insert short brush onto the outer post of the base and remaining brushes onto inner posts. Check the brushes are securely in place.

NOTE: Keep brushes dry for a good polisher effect; wet brushes do not dry and polish the glass.

TIP: If brushes are damp, let the machine run for 20 minutes so brushes can be dried by the hot air.

[Diagram Description: The preparation section includes diagrams illustrating the brush placement for both GP-100 (short brush in center, others on outer posts) and GP-3MINI (short brush on outer post, others on inner posts). Another diagram shows a glass being placed onto the spinning brushes.]

Operation

NOTE: Glasses must be washed, rinsed and still damp when inserted into the glass polisher to get best results. Dry glasses are difficult to polish.

1. Plug power cord into grounded outlet.
2. Press ON/OFF button to turn glass polisher ON.
3. Grasp glass at the base and insert onto the short brush, holding glass base stationary or with slight up and down movement while center brush dries and polishes the inside of the glass and four outer brushes dry and polish the outside of the glass.
4. Remove glass from glass polisher.
5. Press ON/OFF button to turn glass polisher OFF when not in use.

NOTE: The motor will shut off automatically to prevent overheating. Let unit cool down for 15-20 minutes and restart the unit.

Cleaning, Care & Maintenance

CLEANING THE GLASS POLISHER EXTERIOR

1. Ensure glass polisher is OFF and unplug power cord from the outlet.
2. Clean external surface of glass polisher daily using a dampened sponge. Do not immerse glass washer in water or spray with water.
3. Dry the surface with a soft cloth.

CLEANING THE BRUSHES

1. Ensure glass polisher is OFF and unplug power cord from the outlet.
2. Remove brushes by rotating each brush counter clockwise and pulling upward.
3. Wash brushes with mild laundry detergent and rinse well.
4. Use hands to squeeze as much water out of brushes as possible.
5. Insert short brush onto center post of the base.
6. Insert remaining brushes onto outer posts.
7. Plug power cord into a grounded outlet.
8. Press ON/OFF button to turn glass polisher ON. The air blower will dry the brushes in a few minutes.
9. Press ON/OFF button to turn glass polisher OFF when finished or not in use.

REPLACING THE BRUSHES

1. Ensure glass polisher is OFF and unplug power cord from the outlet.
2. Remove brushes by rotating each brush counter clockwise and pulling upward.
3. Insert short brush onto center post of the base.
4. Insert remaining brushes onto outer posts.

Troubleshooting

If your equipment unit does not operate, please check the following prior to placing a service call.

Service & Repair

THIS EQUIPMENT MUST ONLY BE SERVICED BY AN AUTHORIZED AGENT.

NOTE: Parts protected by the manufacturer or its agent are not to be adjusted by the installer unless the installer is an authorized service agent. If you have any questions or problems DO NOT send unit to WINCO® without first contacting our customer service department. See "Limited Warranty" section on www.wincous.com for details.

Electrical Diagram

Circuit diagrams have been provided to assist qualified electricians; only WINCO service agents or qualified electricians should carry out repairs if required. Do not remove any components or service panels on this product.

[Diagram Description: The electrical diagram illustrates the internal wiring. It shows the power input lines (Line, Neutral, Ground) connected through a Fuse and a Power Switch. These then lead to a Heating Element, a Motor, and a Fan Motor. The Motor and Fan Motor are depicted as separate units, likely driving the brushes and air blower respectively.]