MAHANCRIS PT78E01 Rolling Cart
Assembly Instructions
Introduction & General Guidelines
Please read the following instructions carefully and use the product accordingly. Keep this manual and hand it over when you transfer the product. This summary may not include every detail of all variations and considered steps. For further information and help, please contact the manufacturer or seller.
The product is intended for indoor use only. It must be assembled and used in accordance with the provisions of this manual. Unauthorized modifications or uses outside the intended purpose may lead to injury or damage. The seller assumes no responsibility for damages caused by incorrect assembly or improper use.
Warnings
- ⚠️ Children are not allowed to assemble the product. Keep small parts out of reach during assembly as they can be fatal if swallowed or inhaled.
- ⚠️ Children are not allowed to climb or stand on the product to avoid injury from toppling.
- ⚠️ Keep plastic packing bags out of reach of children to avoid potential dangers like suffocation.
- ⚠️ Avoid contact with sharp objects and corrosive chemicals to prevent damage to the product or personal injury.
- ⚠️ Do not use the product if parts are defective or missing, as this can result in damage or injury.
Notes
- The product is designed for indoor use only.
- Do not place the product in damp environments for extended periods to prevent mildew.
- During assembly, first loosely align all screws with the corresponding pre-drilled holes, then tighten them one by one.
- Periodically inspect screw tightness while the product is in use. Re-tighten if necessary to ensure structural integrity.
Tools Required & Parts List
Tools
The following tools may be needed for assembly:
- ? Wrench (Allen wrench provided)
- ✏️ Pencil
- ? Hammer
- ? Screwdriver
- ? Drill (for wall mounting, if applicable)
Note: A drill bit of 8mm (d=8mm) is indicated for wall mounting.
Parts List
| Part ID | Description | Quantity |
|---|---|---|
| 1 | Frame Piece | [x2] |
| 2 | Frame Piece | [x2] |
| 3 | Vertical Support | [x4] |
| 4 | Short Crossbar | [x2] |
| 5 | Short Crossbar | [x2] |
| 6 | Mesh Shelf | [x2] |
| 7 | Mesh Shelf | [x2] |
| 8 | Top Panel / Back Panel | [x2] |
| 9 | Power Strip Mount | [x1] |
| 10 | Small Bracket | [x2] |
Hardware List
| ID | Description | Quantity |
|---|---|---|
| A | Allen Wrench (4MM) | [x1] |
| B | Screw (M6x24mm) | [x24] |
| C | Screw (M6x12mm) | [x12] |
| D | Adjustable Foot | [x4] |
| E1 | Castor Wheel | x2 |
| E2 | Castor Wheel | x2 |
| E3 | Wrench (for Castors) | x1 |
| F1 | Screw (for Power Strip Unit) | x2 |
| F2 | Nut (for Power Strip Unit) | x2 |
| G | Power Strip Unit | [x1] |
| H | Expansion Screw Set (for wall mounting) | [x1] |
Assembly Steps
Step 1
Action: Attach mesh shelves to frame pieces.
Description: Align one mesh shelf (Part 6) with the pre-drilled holes on the lower frame pieces. Insert and loosely tighten screws (Hardware C, x4). Repeat this process for the second mesh shelf (Part 7).
Step 2
Action: Assemble the left and right side frames.
Description: For the left side: Connect Frame Piece (Part 1) to Frame Piece (Part 2) using screws (Hardware B, x2). For the right side: Connect Frame Piece (Part 1) to Frame Piece (Part 2) using screws (Hardware C, x2). Attach Vertical Supports (Part 3) to the assembled Part 2 on both sides, ensuring the holes on the supports face upwards [⬆️].
Step 3
Action: Connect side frames and attach mesh shelves.
Description: Connect the assembled left and right side frames to the main structure. Attach the mesh shelves (Parts 6 and 7) to the Vertical Supports (Part 3), ensuring the holes on the shelves face inward [➡️]. Secure using screws (Hardware B, x8).
Step 4
Action: Attach small brackets.
Description: Attach the Small Brackets (Part 10) to the frame at the designated points. Secure using screws (Hardware C, x4).
Step 5
Action: Attach top panels.
Description: Place the Top Panels (Part 8) onto the frame. Attach the Short Crossbars (Parts 4 and 5) to the Top Panels. Secure using screws (Hardware B, x8).
Step 6
Action: Attach back panels.
Description: Attach the Back Panels (Part 8) to the frame. Secure using screws (Hardware B, x4).
Step 7
Action: Install the power strip mount.
Note: The power strip mount can be installed on the left or right side.
Method 1 (Power strip on the right): Attach the Power Strip Mount (Part 9) to the right side of the frame. Secure with screws (Hardware B, x2).
Method 2 (Power strip on the left): Attach the Power Strip Mount (Part 9) to the left side of the frame. Secure with screws (Hardware B, x2).
Step 8
Action: Install the power strip unit.
Description: Mount the Power Strip Unit (Hardware G) onto the installed Power Strip Mount (Part 9). Secure using screws (Hardware F1, x2) and nuts (Hardware F2, x2).
Step 9
Action: Choose assembly method for the base: Castors or Adjustable Feet.
Method 1 (Assembly of Castors): Attach the Castor Wheels (Hardware E1 x2, E2 x2) to the bottom of the frame. Use the provided wrench (Hardware E3) if needed.
Method 2 (Assembly of Adjustable Feet): Attach the Adjustable Feet (Hardware D, x4) to the bottom of the frame.
Step 10
Action: Wall Mounting (Optional).
Description: This product is equipped with expansion screws (Hardware H) for wall mounting. Please use the correct accessories according to your wall construction (solid/concrete wall or hollow wall). Important: Check for hidden pipes and cables in the wall before drilling.
For solid or concrete wall: Use appropriate method with Hardware H.
For hollow wall: Use appropriate method with Hardware H.
Note: A drill bit of 8mm (d=8mm) is indicated for drilling.
Safety & Maintenance
☔ KEEP DRY
? KEEP FIRE AWAY
? Use a SOFT DRY CLOTH for cleaning.
Periodically check and re-tighten all screws to ensure the structural integrity of the cart.
