MAHANCRIS HB191E01 Headboard Assembly Instructions
Before You Start
Thank you for purchasing this product. Please read this instruction manual carefully before attempting to install. It is very important to ensure each step is followed in the correct order, otherwise assembly difficulties may occur. Retain instructions for future reference. Separate and count all parts and hardware. It is recommended that, where possible, all items are assembled near to the area in which they will be placed in use, to avoid moving the product unnecessarily once assembled. Always place the product on a flat, steady, and stable surface.
BE CAREFUL, BE SAFE
General Guidelines
- Please read the following instructions carefully and use the product accordingly.
- Please keep this manual and hand it over when you transfer the product.
- This summary may not include every detail of all variations and considered steps. Please contact support when further information and help are needed.
Warnings
- Children are not allowed to assemble the product. During assembly, keep small parts out of the reach of children as they may be fatal if swallowed or inhaled.
- Children are not allowed to climb or stand on the product to avoid personal injury caused by toppling.
- Keep plastic packing bags out of reach of children to avoid any potential danger, such as suffocation.
- Avoid sharp objects and corrosive chemicals to prevent damage to the product or the user.
- Please do not use the product if there are defective and/or missing parts, as this can result in damage or injury.
Notes
- The item is only intended for indoor use. Personal injury and/or damage to the product may occur if products are used outside of their intended purposes and/or if products have been changed/modified from their original design. The product must be assembled and used in accordance with the provisions of the manual. The seller does not assume any responsibility or liability with respect to any damage caused by incorrect assembly or improper use.
- Do not place it in a damp environment for extended periods of time to prevent mildew.
- During assembly, first loosely align all screws with the corresponding pre-drilled holes and then tighten the screws one by one.
- Periodically inspect screw tightness while the product is in use. If necessary, re-tighten to ensure structural integrity.
- The total power of the connected electrical appliances shall not exceed the rated power of the socket.
- When using, try to stretch the wires as much as possible and do not bundle them to avoid abnormal overheating.
- When using, please fully insert the electrical plug and keep the wires in full contact to prevent electric shock accidents.
- Prohibit the serial use of plug connections.
- It is prohibited to use the plug in damp places and the product should be kept dry.
- Do not cover the top of the product with any objects during use to prevent overheating and causing a fire.
- If there are any abnormalities such as damaged wires or exposed metal on the product, please stop using it immediately.
Attention Points
- [wrench symbol] [screwdriver symbol] - Ensure you have the necessary tools.
- [person assembling] - Assembly requires careful attention.
- [prohibited symbol] - Keep small parts away from children.
- [flat surface] - Assemble on a flat, stable surface.
- [contact support] - Contact us if you need further assistance.
Parts List
| Part ID | Description | Quantity |
|---|---|---|
| 1 | Long, narrow panel with a slot | [x1] |
| 2 | Long, narrow panel with a slot | [x1] |
| 3 | Large rectangular panel | [x2] |
| 4 | Small rectangular panel | [x1] |
| 5 | Long, narrow panel with a slot | [x1] |
| 6 | Long, narrow panel with a slot | [x1] |
| 7 | Large rectangular panel | [x1] |
| 8 | Small rectangular panel | [x1] |
| 9 | U-shaped frame piece | [x2] |
| 10 | U-shaped frame piece | [x2] |
| 11 | Long, thin rod/bar | [x2] |
| 12 | Long, thin rod/bar | [x2] |
| 13 | Long, thin rod/bar | [x2] |
| 14 | Long, thin rod/bar | [x2] |
Hardware List
| Hardware ID | Description | Quantity |
|---|---|---|
| A | L-shaped bracket | [x1] |
| B | Screwdriver | [x1] |
| C | Screw (long, threaded) | [x24] |
| D | Bolt (medium length) | [x8] |
| E | Screw (short, flat head) | [x20] |
| F | Screw (small, flat head) | [x4] |
| G | Dowel/pin with cap | [x4] (G1x4) |
| H | Various small metal fittings (brackets, connectors) | H1x1, H2x1, H3x4 |
| I | Plastic cap/cover | [x2] |
| J | Various small metal fittings (brackets, connectors, screws) | J1x1, J2x1, J3x2, J4x2 |
| K | Plastic mounting bracket | [x2] |
| L | Metal bracket | [x2] |
| M | Metal bracket | [x2] |
| N | Bolt and nut | N1x8, N2x8 |
| O | Washer | [x16] |
| P | Wrench | [x1] |
Assembly Steps
- Step 1: Frame Assembly
Attach the U-shaped frame pieces (9 and 10) together. Use hardware E (x8) to secure them. It is recommended to complete the assembly on a flat ground or carpet.
- Step 2: Side Panel Attachment
Attach the side panel (2) to the main frame piece (1). Use hardware G1 (x4), E (x4), and L (x2). Secure with J3 (x2) and J1 (x1), ensuring the correct orientation of J3.
- Step 3: Connecting Frame Pieces
Connect the U-shaped frame piece (9) to the assembled side panels (1 and 2). Use hardware C (x4). Note the direction of the holes for proper alignment.
- Step 4: Attaching Panels
Attach the small rectangular panel (4) to the large rectangular panel (6) using hardware C (x2). Note the direction of the holes. Then, attach the large rectangular panel (7) to panel (6) using hardware C (x2), again noting hole direction.
- Step 5: Integrating Panels
Attach the assembly from Step 4 (panels 4, 6, 7) to the main structure. Use hardware C (x4) to connect panel 5 to panels 4 and 7. Then, attach this entire assembly to the main frame (1 and 2) using hardware G2 (x4).
- Step 6: Securing Top Panels
Attach the large rectangular panels (3) to the structure. Use hardware C (x8) to secure panels 3 to the supporting pieces (5 and 6).
- Step 7: Attaching Support Rods
Connect the long, thin rod/bars (11) to the other rod/bars (12) using hardware E (x4). Then, attach these assembled units to the main structure using hardware D (x4).
- Step 8: Reinforcing Structure
Further reinforce the structure by attaching the rod/bars (11 and 12) using hardware C (x4).
- Step 9: Attaching Top Rods
Connect the long, thin rod/bars (13) to the other rod/bars (14) using hardware E (x4). Then, attach these assembled units to the top of the headboard structure using hardware D (x4).
- Step 10: Installing Shelf/Accessory Mount
Attach the small rectangular panel (8) to the mounting bracket assembly. Use hardware I (x2), J2 (x1), and J4 (x2). Secure with H2 (x1) and H3 (x2). Ensure correct screw types (J3 vs J4) are used.
- Step 11: Final Placement of Shelf/Accessory
Insert the assembled part from Step 10 (panel 8) into its designated position within the headboard structure.
- Step 12: Attaching Electrical Components
Attach the plastic mounting brackets (K, x2) and hardware F (x4) using H1 (x1) and H3 (x2). Note the power limit of this product is 1500W. Do not connect high-power household appliances.
- Step 13: Locking Mechanism
Engage the locking mechanism as shown in the diagram to secure components.
- Step 14: Attaching to Bed Frame - Method 1
When connecting the headboard to the bed frame, determine the correct method based on your bed frame width. Method 1: If the bed frame width is the same as the headboard width, no additional bracket (M) is needed. Use hardware N1 and N2 to attach directly.
- Step 15: Attaching to Bed Frame - Method 2
Method 2: If the bed frame width is smaller than the headboard width, install bracket M (x2) as shown in the figure using hardware N1 and N2.
- Step 16: Attaching to Bed Frame - Method 3
Method 3: If the bed frame width is larger than the headboard width, install bracket M (x2) as shown in the figure using hardware N1 and N2.
- Step 17: Final Check
Before using the product, please ensure that all screw fittings are positioned correctly and fastened securely.
