On/Off Outdoor Module

About On/Off Outdoor Module

The INSTEON On/Off Outdoor Module is a simple device for remotely controlling any plug-in device, whether located indoors or outdoors, with the touch of a button. It can receive commands from any INSTEON controller or be linked to other INSTEON devices to act as a controller itself.

Image Description: The module is a compact, dark gray rectangular device with a power cord and plug at one end, and an AC outlet on the front face. Labels indicate a "Status LED" and a "Set button" on the front, and an "Outlet" where the appliance is plugged in.

Features and Benefits

• Installs and links to other INSTEON devices in minutes.
• Controls standard incandescent loads up to 1800 Watts and inductive loads up to 15 Amps.
• Weatherproof design for harsh outdoor conditions.
• Dual-color Status LED and beeper indicate INSTEON setup mode activity and operational states.
• Load Sensing can be easily enabled and disabled.
• Stores setup state in memory, retaining settings during power outages.
• Comes with a two-year warranty.

In the Box

• On/Off Outdoor Module
• Quick Start Guide

Optional Accessories

• Mini Remote
• INSTEON Hub

Before Installation

CAUTIONS AND WARNINGS

Read and understand these instructions before installing and retain them for future reference. The On/Off Outdoor Module is intended for installation in accordance with the National Electric Code and local regulations in the United States or the Canadian Electrical Code and local regulations in Canada. It is not designed or approved for use on power lines other than 120V 60Hz, single phase. Attempting to use it on non-approved power lines may have hazardous consequences.

Prior to installing, please review the entire installation procedure and take the following precautions:

• Ensure the On/Off Outdoor Module is connected to a 3-prong AC outlet that includes a Ground Fault Circuit Interrupt (GFCI) feature. If plugged into an outlet without GFCI protection, ensure there is a GFCI device upstream (closer to the electrical panel or a GFCI circuit breaker).
• Test your GFCI protection each time the module is plugged in, and on a monthly basis. To test: plug in the module, turn the connected load on, push the TEST button on the GFCI outlet/breaker. The unit must stop operating. Wait 5 seconds, then push the RESET button. The module should receive power and the load should turn on. If the GFCI fails this test, disconnect power and correct the problem. Consult your GFCI device's instructions for specific testing. Replace the GFCI device if in doubt.
• Do not bury the On/Off Outdoor Module, any electrical cable, or connected component. A buried power cord can lead to electrocution.
• Do not allow vegetation to grow on or around the module.
• Do not install the module where water can accumulate around it.
• If an extension cord is used, it must be properly grounded and of adequate capacity. A light-duty or medium-duty cord may cause voltage drop, leading to overheating.
• Do not attempt to open the module; the case is sealed and contains no user-serviceable parts.
• Do not use the module to control devices that preserve, maintain, or contribute to human or animal safety or life support.
• Do not plug the module into an outlet controlled by a switch, as turning off the switch will cut power to the module.
• Do not plug the module into a filtered power strip or AC line filter.
• Ensure the device's built-in switch is in the 'on' position.
• Do not exceed the load rating. Check and sum all attached electrical devices; the total must not exceed 15 Amps.
• Do not use any damaged or poor-condition electrical or extension cords.

IMPORTANT!

If you have any difficulties or questions, consult an electrician. For INSTEON support, call 866-243-8022.

Installation

1. Plug the appliance/device (the load) you want to control into the On/Off Outdoor Module outlet.
2. Plug the On/Off Outdoor Module into an unswitched wall outlet. The Status LED will turn on solid green, and the load will turn on. (If the load does not turn on, tap the Set button.)
3. Allow the On/Off Outdoor Module to hang down from the outlet.

Note: After installation, the load's built-in switch will not control the load unless Load Sensing is enabled. See Load Sensing.

Using On/Off Outdoor Module

Local Control Operation

Note: The table above seems to be missing data from the original PDF. Based on context, it likely describes button actions and LED feedback.

LED Activity

Adjust Local Settings

LED On or Off

Default: On

This setting is adjustable only via software or a central controller. When enabled, the LED will be green when the load is on and red when the load is off.

Blink on Traffic

Default: Enabled

This setting is adjustable only via software or a central controller. The module's LED will blink green for INSTEON traffic and if it detects noise that could disrupt communication.

Programming Lock

Default: Disabled

This setting is adjustable only via software or a central controller. When enabled, the Programming Lock disables the set button, preventing users from adjusting settings or modifying links. This is typically used in commercial or installer applications.

INSTEON Setup

Some products have subtle differences in their setup procedures. Please refer to the other devices' owner's manuals for details.

INSTEON Controllers, Responders and Links

Let's define a few terms:

• The INSTEON "transmitter" is called a controller.
• The INSTEON "receiver" is called a responder.
• The association between the controller and responder is called a link.

Diagram Description: A simple diagram shows a box labeled "Controller" with an arrow pointing to a box labeled "Link", which then points to a box labeled "Responder".

Note that a link is one way. To control "the other way," simply add a link "the other way."

Make On/Off Outdoor Module a Responder

1. Press and hold the controller's set button until it beeps. The controller's LED will start blinking. You have four minutes to complete the next steps before linking mode times out.
2. Use the On/Off Outdoor Module's set button to adjust the load to the desired state (on or off).
3. Press and hold the On/Off Outdoor Module's set button until it double-beeps. The controller will double-beep and its LED will stop blinking.
4. Test the link by tapping the controller button on and off. The lamp connected to the On/Off Outdoor Module will respond appropriately.

Note: The link just created is one way. See "Make On/Off Outdoor Module a Controller" or "Groups" to add another link to keep the two products in sync. If you wish the load to be off when the link is activated (e.g., for an "all off" scene), turn off the load in step #2.

Make On/Off Outdoor Module a Controller

1. Press and hold the On/Off Outdoor Module's set button until it beeps. The module's LED will start blinking green.
2. Adjust the responder to the desired brightness state (e.g., on, 50%, or even off).
3. Press and hold the responder's set button until it double-beeps. The On/Off Outdoor Module's LED will stop blinking.
4. Test by tapping the On/Off Outdoor Module's set button to turn the load on/off. The responder will respond appropriately.

Groups

Devices in a group share identical settings (e.g., on-level, ramp rate), keeping all group members synchronized. Every device in a group acts as both a controller and responder to all other devices. A common example is a 3-way lighting circuit. The following steps create a virtual 3-way circuit using devices "A" and "B":

1. Turn A and B on.
2. Press and hold A's set button until it beeps. A's status LED will start blinking green.
3. Press and hold B's set button until it double-beeps. A will double-beep and its LED will stop blinking.
4. Press and hold B's set button until it beeps. B's LED will start blinking green.
5. Press and hold A's set button until it double-beeps. B will double-beep and its LED will stop blinking.
6. Test by turning the load on and off from A and then from B. The load(s) and both A and B LEDs will remain in sync.

Scenes

Devices in a scene can have different settings, allowing for advanced scene creation. Software is recommended for scene management.

Example of a scene with 1 controller and On/Off Outdoor Module as a member:

1. Press and hold the controller's set button until it beeps. The controller's LED will start blinking green.
2. Tap the controller's set button. The controller's LED will start double-blinking green.
3. Use the On/Off Outdoor Module's set button to adjust the load to the desired state (on or off).
4. Press and hold the On/Off Outdoor Module's set button until it double-beeps.
5. For each additional scene member:
   • Adjust member to desired scene brightness.
   • Press and hold Set button until it double-beeps.
6. Tap the controller's set button. The controller will beep and its LED will stop blinking.
7. Test by tapping the controller button on and off. The On/Off Outdoor Module and other scene responders will all respond appropriately.

Remove On/Off Outdoor Module as a Responder

If you no longer want a controller button to control the On/Off Outdoor Module, follow these directions.

Note: If you ever wish to uninstall the module, it is important to remove all its responder links. Otherwise, controllers will repetitively retry commands, creating network delays.

1. Press and hold the controller button until it beeps. The LED will start blinking green.
2. Press and hold the controller button until it beeps again. The LED will start blinking red.
3. Press and hold the On/Off Outdoor Module's set button until it double-beeps. The controller's LED will stop blinking.
4. Test by tapping the controller button on and off. The On/Off Outdoor Module will no longer respond.

Remove On/Off Outdoor Module as a Controller

If you no longer want the On/Off Outdoor Module to control another device (or are removing it from your network), follow the instructions below for each responder.

1. Press and hold the On/Off Outdoor Module's set button until it beeps. The LED will start blinking green.
2. Press and hold the On/Off Outdoor Module's set button until it beeps again. The LED will start blinking red.
3. Press and hold the responder's set button until it double-beeps. The On/Off Outdoor Module will double-beep and its LED will stop blinking.
4. Test by tapping the On/Off Outdoor Module on and off. The former responder will not respond.

Load Sensing

Load Sensing allows you to control the load plugged into the On/Off Outdoor Module from its local switch, in addition to any linked controllers. Load Sensing is disabled by default but can be enabled.

Enable Load Sensing

1. Press and hold the On/Off Outdoor Module's set button until it beeps (3 seconds). The module's Status LED will begin blinking green.
2. Triple-tap the On/Off Outdoor Module's set button quickly. The Status LED will stop blinking and turn on solid green if the load is on, or solid red if it is off.
3. Test by turning the load on and off from its built-in switch. The load will turn on and off.

Disable Load Sensing

1. Press and hold the On/Off Outdoor Module's set button until it beeps (3 seconds). The module's Status LED will begin blinking green.
2. Double-tap the On/Off Outdoor Module's set button quickly. The Status LED will stop blinking and turn on solid green if the load is on, or solid red if it is off.
3. Test by turning the load on and off from its built-in switch. The load will not respond.

Specifications

General

INSTEON

X10

Mechanical

Electrical

Troubleshooting

If you have tried these solutions, reviewed this Owner's Manual, and still cannot resolve an issue, please call INSTEON Support Line at 866-243-8022.

Phase Bridge Detect Beacon/RF Range Test

The On/Off Outdoor Module automatically bridges electrical phases in your home via communications with other dual-band devices on the "other phase." This is important in 2-phase homes with powerline-only INSTEON products or buildings with 2- and 3- phase circuits. The phase bridge detect beacon can also be used as an RF range test to see if your devices are within communication range. You will need at least one other INSTEON dual-band device installed.

1. Quickly tap the Set button four times. The On/Off Outdoor Module will start beeping once per second, and the LED will turn solid green.
2. Check the LED behavior of other dual-band devices:
   • Phase Bridge Detect Beacon:
     • If the other dual-band device is blinking green, it is on the other phase: Device provides a phase bridge to Micro module.
     • If the other dual-band device is blinking red, it is on the same phase: Device does not provide a phase bridge to Micro module. Relocate if necessary (and practical).
     • If the other dual-band device is not blinking: Device is not within RF range of Micro module, so it does not provide a phase bridge. Relocate if necessary (and practical) or add an additional dual-band device.
   • RF Range Test:
     • If the LED is blinking: Device is within RF communication range.
     • If the LED is not blinking: Device is not within RF communication range. Relocate if necessary (and practical) or add an additional dual-band device.
3. Tap the Set button. The On/Off Outdoor Module will stop beeping, and other device LEDs will stop blinking.

Factory Reset

All settings, links, and scenes will be erased.

1. If you are using a controller to control the On/Off Outdoor Module, be sure to unlink it from the controller first.
2. Unplug the On/Off Outdoor Module.
3. While pressing and holding the Set button, plug the On/Off Outdoor Module back in. Do not release the Set button. The module will begin to emit a long beep, and the Status LED will turn green.
4. When the long beep stops, release the Set button. The Status LED will flash red and then turn green. After a few seconds, the load will turn on.

Certification and Warranty

Certification

This product has been thoroughly tested by ITS ETL SEMKO, a nationally recognized independent third-party testing laboratory. The North American ETL Listed mark signifies that the device has been tested to and has met the requirements of a widely recognized consensus of U.S. and Canadian device safety standards, that the manufacturing site has been audited, and that the manufacturer has agreed to a program of quarterly factory follow-up inspections to verify continued conformance.

FCC and Industry Canada Compliance Statement

This device complies with FCC Rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions:

• (1) This device may not cause harmful interference, and
• (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.

The digital circuitry of this device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and television reception. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause such interference, which can be verified by turning the device off and on, the user is encouraged to eliminate the interference by one or more of the following measures:

• Re-orient or relocate the receiving antenna of the device experiencing the interference.
• Increase the distance between this device and the receiver.
• Connect the device to an AC outlet on a circuit different from the one that supplies power to the receiver.
• Consult the dealer or an experienced radio/TV technician.

WARNING:

Changes or modifications to this device not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

ETL/UL Warning (Safety Warning)

CAUTION:

To reduce the risk of overheating and possible damage to other equipment, do not install this device to control a receptacle, a motor-operated appliance, a fluorescent lighting fixture, or a transformer-supplied appliance.

Gradateurs commandant une lampe a filament de tungstene - afin de reduire le risqu de surchauffe et la possibilite d'endommagement a d'autres materiels, ne pas installer pour commander une prise, un appareil a moteur, une lampe fluorescente ou un appareil alimente par un transformateur.

Limited Warranty

Seller warrants to the original consumer purchaser of this product that, for a period of two years from the date of purchase, this product will be free from defects in material and workmanship and will perform in substantial conformity to the description of the product in this Owner's Manual. This warranty shall not apply to defects or errors caused by misuse or neglect. If the product is found to be defective in material or workmanship, or if the product does not perform as warranted above during the warranty period, Seller will either repair it, replace it, or refund the purchase price, at its option, upon receipt of the product at the address below, postage prepaid, with proof of the date of purchase and an explanation of the defect or error. The repair, replacement, or refund that is provided for above shall be the full extent of Seller's liability with respect to this product. For repair or replacement during the warranty period, call 800-762-7845 with the Model # and Revision # of the device to receive an RMA# and send the product, along with all other required materials to:

INSTEON
ATTN: Receiving
16542 Millikan Ave.
Irvine, CA 92606-5027

Limitations

The above warranty is in lieu of and Seller disclaims all other warranties, whether oral or written, express or implied, including any warranty or merchantability or fitness for a particular purpose. Any implied warranty, including any warranty of merchantability or fitness for a particular purpose, which may not be disclaimed or supplanted as provided above shall be limited to the two-year of the express warranty above. No other representation or claim of any nature by any person shall be binding upon Seller or modify the terms of the above warranty and disclaimer.

Home automation devices have the risk of failure to operate, incorrect operation, or electrical or mechanical tampering. For optimal use, manually verify the device state. Any home automation device should be viewed as a convenience, but not as a sole method for controlling your home.

In no event shall Seller be liable for special, incidental, consequential, or other damages resulting from possession or use of this device, including without limitation damage to property and, to the extent permitted by law, personal injury, even if Seller knew or should have known of the possibility of such damages. Some states do not allow limitations on how long an implied warranty lasts and/or the exclusion or limitation of damages, in which case the above limitations and/or exclusions may not apply to you. You may also have other legal rights that may vary from state to state.

Protected under U.S. and foreign patents (see www.insteon.com/patents)

© Copyright 2013 INSTEON, 16542 Millikan Ave., Irvine, CA 92606, 866-243-8022, www.insteon.com