OWNER'S MANUAL

CONTENTS

• IMPORTANT SAFETY INSTRUCTIONS
• PRE-SETUP CHECK LIST
• INSTALLATION
• SET-UP INSTRUCTION IN WINTER
• USING THE SPA
• MAINTENANCE
• DISASSEMBLY AND STORAGE
• TROUBLESHOOTING
• ERROR CODES

For FAQ, Manuals, Videos, or spare Parts, please visit bestwaycorp.com/support

IMPORTANT SAFETY INSTRUCTIONS

SAFETY INSTRUCTIONS

Carefully read, understand, and follow all information in this user manual before installing and using the spa.

IMPORTANT SAFETY INSTRUCTIONS - READ AND FOLLOW ALL INSTRUCTIONS.

WARNING:

• The spa must be supplied through an isolating transformer or supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30mA.
• The spa must be connected to a grounded mains supply socket with a supply cord fitted with a plug and PRCD with a tripping current of 10mA.
• The pump must be tested before each use; to test, follow the instruction of the pump.
• If the supply cord is damaged, it must be replaced by the manufacturer, service agent or similarly qualified persons in order to avoid a hazard.
• To reduce the risk of electric shock, do not use an extension cord to connect the unit to electric supply; provide a properly located outlet.
• No part of the appliance is to be located above the bath during use.
• Parts containing live parts, except parts supplied with safety extra-low voltage not exceeding 12V, must be inaccessible to a person in the spa pool; Parts incorporating electrical components, except remote control devices, must be located or fixed so that they cannot fall into the spa pool.
• The spa must be supplied by an earthed power source.
• The power source on the wall of the building should keep more than 4m away from the pool.
• Warning: Always keep plug dry, plugging in with a wet plug is definitely forbidden!
• The plug shall be directly connected only to an earthed socket-outlet of the fixed electrical installation.
• It is necessary to have the plug accessible after installation of the spa.

CAUTION:

In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.

After using your spa for 3-5 years, you should contact your local qualified maintenance technician to ensure the safety and performance of the spa. The main components, such as the heating element, air blower motor and non-return valves within the electric unit should be checked and replaced (if necessary) by professional persons.

• TO AVOID ELECTRIC SHOCK, DO NOT USE THE SPA WHEN IT IS RAINING, THUNDERING OR LIGHTNING.
• Never wear your contact lenses when in your spa.
• Do not use the spa during chemical maintenance.
• Extension cords can't be used.
• Don't plug or unplug the appliance if your hand is wet.
• Always unplug the appliance:
  • before cleaning or other maintenance
  • if left unattended on holidays
• When the appliance will not be used for a long time, such as in the winter, the spa or pool set should be disassembled and stored indoors.
• For safety reasons, only use the accessories provided or approved by the spa manufacturer.
• Do not place the spa on a slippery surface, and make sure the surface is free of sharp objects before installation.
• Never place any electrical supplies or appliances, such as a light, telephone, radio, or television, within 2m of the spa.
• Caution: Read the instruction before using the appliance and installation or reassemble every time.
• Safekeeping the instruction. If instruction is missed, please contact the manufacturer or search it on the website www.bestwaycorp.com.
• Warning: For electric safety, a PRCD is incorporated in the power cord. If the leakage current is detected more than 10mA, the device will operate and cut-off the power supply. In such a case, please unplug and stop using the spa at once. Don't reset the product by yourself. You must contact the local service agent to check and repair the product.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. (For EU market)
• Cleaning and user maintenance must be performed by an adult above 18 years old who is familiar with the risk of electric shock. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. (For market other than EU)
• Water attracts children; always attach a spa cover after each use.
• Do not bury the cord. Locate the cord to minimize abuse from lawn mowers, hedge trimmers, and other equipment.
• DANGER - Risk of Accidental Drowning (especially children under 5 years). Caution shall be exercised to prevent unauthorized access to the spa by children. This can be reached by an adult supervisor securing the means of access or installing a safety protection device to the spa. To avoid accidents during spa use, ensure that children are kept under constant adult supervision.
• DANGER - Risk of Injury. The suction fittings in this spa are sized to match the specific water flow created by the pump. Should the need arise to replace the suction fittings or the pump, be sure that the flow rates are compatible. Never operate the spa if the suction fittings are broken or missing. Never replace a suction fitting with one rated less than the flow rate marked on the original suction fitting.
• RISK OF INJURY. Never operate the spa if inlet / outlet pipes are broken or missing. Never attempt to replace the inlet / outlet pipes. Always consult your local Aftersales centre.
• RISK OF ELECTRIC SHOCK. Install at least 2m from all metal surfaces.
• RISK OF ELECTRIC SHOCK. Never operate any electrical appliance when in your spa or when your body is wet. Never place any electric appliance, such as a light, telephone, radio, or television, within 2m of the spa.
• Consider that the comfortable temperature range during use may be lower than the maximum safe temperature.
• During pregnancy, soaking in hot water may cause damage to the fetus. Limit use to 10 minutes at a time.
• TO REDUCE THE RISK OF INJURY:
  1. The water in a spa should never exceed 40°C (104°F). Water temperature between 38°C (100°F) and 40°C (104°F) is considered safe and comfortable for a healthy adult. Lower water temperatures are recommended for young children and when spa use exceeds 10 minutes.
  2. Since excessive water temperatures have a high potential for causing fetal damage during the early months of pregnancy, pregnant or possibly pregnant women should limit spa water temperature to 38°C (100°F).
  3. Before entering a spa, the user should measure the water temperature with an accurate thermometer since the tolerance of the water temperature regulating device varies.
  4. The use of alcohol, drugs, or medication before or during spa use may lead to unconsciousness with the possibility of drowning.
  5. Obese persons and persons with a history of heart disease, low or high blood pressure, circulatory system problems, or diabetes should consult a physician before using a spa.
  6. Persons using medication should consult a physician before using a spa since some medication may induce drowsiness while other medication may affect heart rate, blood pressure, and circulation.
  7. Avoid putting your head under water at all times.
  8. Avoid swallowing spa water.
• TO REDUCE THE RISK OF INJURY: Never pour water with a temperature higher than 40°C (104°F) into the spa pool directly.
• The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia. Hyperthermia occurs when the internal temperature of the body reaches a level that is several degrees above the normal body temperature of 37°C (98.6°F). The symptoms of hyperthermia include an increase in the internal temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia include failure to perceive heat; failure to recognize the need to exit the spa or hot tub; unawareness of impending hazard; fetal damage in pregnant women; physical inability to exit the spa or hot tub; and unconsciousness resulting in the danger of drowning.
• Electric installations should follow national wiring rules; consult a qualified electrician with any questions.
• These warnings, instructions, and safety guidelines address some common risks of water recreation, but they cannot cover all risks and dangers in all cases. Always use caution, common sense, and good judgment when enjoying any water activity. Retain this information for future use. In addition, the following information can be supplied depending on the spa type:

Non Swimmers safety

• Continuous, active, and vigilant supervision of weak swimmers and non-swimmers, especially in exercise spas, by a competent adult is required at all times (remembering that children under five years of age are at the highest risk of drowning).
• Designate a competent adult to supervise the spa each time it is being used.
• Weak swimmers or non-swimmers should wear personal protection equipment, especially when using the exercise spa.
• When the spa is not in use, or unsupervised, remove all toys from the spa and its surrounding area to avoid attracting children to the spa.

Safety devices

• A safety cover or other safety protection device shall be used, or all doors and windows (where applicable) shall be secured to prevent unauthorized access to the spa.
• Barriers, covers, alarms, or similar safety devices are helpful aids, but they are not substitutes for continuous and competent adult supervision.

Safety equipment

• It is recommended to keep rescue equipment (e.g., a ring buoy) by the spa (if appropriate).
• Keep a working phone and a list of emergency phone numbers near the spa.

Safe use of the spa

• Encourage all users, especially children, to learn how to swim.
• Learn Basic Life Support (Cardiopulmonary Resuscitation - CPR) and refresh this knowledge regularly. This can make a life-saving difference in the event of an emergency.
• Instruct all spa users, including children, what to do in case of an emergency.
• Never dive into any shallow body of water. This can lead to serious injury or death.
• Do not use the spa when using alcohol or medication that may impair the bather's ability to safely use the spa.
• When covers are used, remove them completely from the water surface before entering the spa.
• Protect spa occupants from water-related illnesses by advising them to keep water treated and practicing good hygiene.
• Consult the water treatment guidelines in the user's manual.
• Store chemicals out of the reach of children.
• Use the signage provided on the spa or within 2000 mm of the spa in a prominent visible position.
• Removable ladders, when removed, shall be stored safely where children cannot climb on it.

CONSULT YOUR PHYSICIAN FOR RECOMMENDATIONS.

CAUTION:

• We strongly recommend not to unfold and inflate the spa if the ambient temperature is below 15°C (59°F). We suggest inflating the spa indoors, and then continuing set up outdoors. If the outdoor temperature is lower than 6°C (42.8°F), the spa heater must always be on. In this mode, the Freeze Shield™ system can keep the internal temperature between 6°C (42.8°F) and 10°C (50°F) to prevent damage, such as water freezing in the pipes or the circulation system.

Important: If the Freeze Shield™ system isn't working, alarms will pop up on the spa. Be sure to check the status of your spa if the outdoor temperature is below 6°C (42.8°F). In case of a long-term absence from home when there is a risk of temperatures falling below 6°C (42.8°F), we strongly suggest disassembling the spa and storing it following the storage procedure.

• Do not use the spa alone.
• People with infectious diseases should not use a spa.
• Do not use the spa immediately following strenuous exercise.
• Always enter and exit the spa slowly and cautiously. Wet surfaces are slippery.
• To avoid damage to the pump, the spa must never be operated unless the spa is filled with water.
• Immediately leave the spa if the user feels uncomfortable or sleepy.
• Whenever the spa is emptied, the filter should be cleaned (and drained/dried, where applicable).
• Any manual dosing of chemicals shall not be performed while bathers are present in the spa.
• Never add water to chemicals. Always add chemicals to water to avoid strong fumes or violent reactions that may result in hazardous chemical spray.
• Regarding the information pertaining to cleaning, maintenance of water, and disposal of water, please see the section "MAINTENANCE".
• Regarding the information pertaining to the installation, please refer to the below paragraph of the manual.

NOTE:

• Please examine equipment before use. Notify Bestway at the customer service address listed in this manual for any damaged or missing parts at the time of purchase. Verify that the equipment components represent the models that you had intended to purchase.
• This product is not intended for commercial use.

SAVE THESE INSTRUCTIONS

SELECTED LOCATION

Indoor and outdoor & above ground & portable wiring & portable spa

WARNING: The selected location has to be able to support the expected load.

WARNING: An adequate drainage system has to be provided to deal with overflow water for both indoor and outdoor installations.

• Always keep the spa cover on to minimize heat loss during heating of the spa between uses (but not while it is being used). Ensure the cover is fitted tightly, as per instructions to maximize insulation. It is recommended that the cover, when not in use, should be kept off the ground to retain its cleanliness (particularly the surface in close proximity to the water spa water surface). The cover should be stored in an appropriate location, where it cannot be damaged, or cause damage.
• Check the set water temperature and consider lowering it for the times when the spa will typically not be in use.
• Depending on external conditions, consider turning off the heater entirely if not using the spa for an extended period of time (where the spa provides this option, but still maintains residual disinfection/pH-values).
• It is recommended to use an insulating ground cloth underneath the spa to minimize heat loss through the bottom of the spa.
• Maintain clean filters to preserve appropriate working conditions for the pump and avoid unnecessary water replacement and re-heating.
• Keep the spa away from the rest area to minimize noise disturbance.
• Recommended to ask a qualified contractor or a structural engineer to verify if the support material is strong enough to support the maximum design load of the spa, spa water and bathers. Read the filled weight information on the package.
• Please keep at least 1m clearance around the spa.
• Consult your local government authority for water regulations related to convenient water supply for filling the spa.
• Recommended to consult experts and/or local authorities to apply local or national laws/regulations relating to childproof fencing, safety barriers, lighting, and other safety requirements.
• Do not put the cover on the ground or any other dirty surface when not in place on the spa.
• When the spa is being used, the cover should be placed in a clean, dry area, otherwise it can pick up dirt and bacteria. Covers should not be put on wooden tables or wooden decking because of the risk of bleaching the wood. A cover lifter, or similar device, is useful for ensuring that the cover does not come into contact with the ground. A cover lifter is strongly recommended for spas in rental settings.

IMPORTANT: Because of the combined weight of the Lay-Z-Spa, water, and users, it is extremely important that the base where the Lay-Z-Spa is installed is smooth, flat, level and capable of uniformly supporting the weight for the entire time the Lay-Z-Spa is installed (not on the carpet or other similar material). If the Lay-Z-Spa is placed on a surface, which does not meet these requirements, any damage caused by improper support is not covered under the manufacturer's warranty. It is the responsibility of the Lay-Z-Spa owner to assure the integrity of the site at all times.

1. Indoor Installation:

Be aware of special requirements if you install the spa indoors.

• Humidity is a natural side effect with Lay-Z-Spa installation. Determine the effects of airborne moisture on exposed wood, paper, etc. in the proposed location. To minimize these effects it is best to provide plenty of ventilation to the selected area. An architect can help determine if more ventilation is needed.
• Consult your local government authority for installation regulations.
• Keep suitable air treatment in the spa chamber (ventilation and dehumidification) regularly to preserve the bathers' safety and comfort.
• Do not install the spa on carpet or other floor materials (e.g. untreated cork, timber or other porous materials) that promote or harbour moisture and bacteria, or that could be affected by water treatment chemicals used in the spa.
• Empty the spa before removing it from the chamber or building.

2. Outdoor Installation:

• During filling, draining or when in use, water may flow out of the spa. Therefore the Lay-Z-Spa should be installed near a floor drain.
• Do not leave the spa's surface exposed to direct sunlight for long periods of time.
• Consult your local professional installers for environmental conditions, such as ground water and risk of frost.
• Recommended to protecting the spa from direct sunlight exposure by a cover when not in use.

PRCD WARNING

WARNING: Before inserting the plug into a power outlet, make sure the current rate of the power outlet is suitable for the pump.

WARNING: Using an extension lead or multi plug adaptor with the spa heater can cause the plug to overheat, causing damage to the equipment and surrounding items. The spa is a class I electrical appliance and must be connected directly to a grounded socket. It is recommended to only use a socket which is resistant to humidity and capable of high power loading. Regularly check the plug and socket for signs of damage before using the spa – do not use the spa if the plug or socket is damaged. If you are unsure about the quality of the electrical supply, please consult a qualified electrician before use.

WARNING: The PRCD plug must be tested before each use to avoid risk of electric shock.

WARNING: Do not use the pump if this test fails. For assistance, please visit the support section on the Bestway website, www.bestwaycorp.com.

PRE-SETUP CHECK LIST

PARTS CHECKS

Please examine equipment before use. Notify Bestway customer service of any damaged or missing parts at the time of purchase. Verify that the equipment components represent the model that you had intended to purchase. For reference, please use the diagrams on the Bestway support website.

This manual covers the following Lay-Z-Spa AirJet models, with varying dimensions and capacities, but similar setup components:

• MIAMI AIRJET S100102 (60001): 1.80 m x 66 cm / 71" x 26", 2-4 persons, 669 L (177 gal), 696 kg (1,534 Lb) filled weight.
• CANCUN AIRJET S100102 (60003): 1.80 m x 66 cm / 71" x 26", 2-4 persons, 669 L (177 gal), 696 kg (1,534 Lb) filled weight.
• BAHAMAS AIRJET S100102 (60005): 1.80 m x 66 cm / 71" x 26", 2-4 persons, 669 L (177 gal), 696 kg (1,534 Lb) filled weight.
• TAHITI AIRJET S100102 (60007): 1.80 m x 66 cm / 71" x 26", 2-4 persons, 669 L (177 gal), 696 kg (1,534 Lb) filled weight.
• BALI AIRJET S100102 (60009): 1.80 m x 66 cm / 71" x 26", 2-4 persons, 669 L (177 gal), 696 kg (1,534 Lb) filled weight.
• VEGAS AIRJET S100102 (60011): 1.96 m x 61 cm / 77" x 24", 4-6 persons, 775 L (205 gal), 806 kg (1,777 Lb) filled weight.
• PARIS AIRJET S100102 (60013): 1.96 m x 66 cm / 77" x 26", 4-6 persons, 806 L (213 gal), 840 kg (1,851 Lb) filled weight.
• IBIZA AIRJET S100102 (60015): 1.80 m x 1.80 m x 66 cm / 71" x 71" x 26", 4-6 persons, 778 L (205 gal), 807 kg (1,779 Lb) filled weight.
• PALM SPRINGS AIRJET S100102 (60017): 1.96 m x 71 cm / 77" x 28", 4-6 persons, 916 L (242 gal), 954 kg (2,103 Lb) filled weight.
• HONOLULU AIRJET S100102 (60019): 1.96 m x 71 cm / 77" x 28", 4-6 persons, 916 L (242 gal), 954 kg (2,103 Lb) filled weight.
• HAWAII AIRJET S100102 (60021): 1.80 m x 1.80 m x 71 cm / 71" x 71" x 28", 4-6 persons, 840 L (222 gal), 879 kg (1,938 Lb) filled weight.
• ST. MORITZ AIRJET S100102 (60023): 2.16 m x 71 cm / 85" x 28", 5-7 persons, 1190 L (314 gal), 1210 kg (2,668 Lb) filled weight.
• HELSINKI AIRJET S100102 (60025): 1.80 m x 66 cm / 71" x 26", 5-7 persons, 1123 L (297 gal), 1155 kg (2,548 Lb) filled weight.
• ST. LUCIA AIRJET S100102 (60037): 1.70 m x 66 cm / 67" x 26", 2-3 persons, 605 L (160 gal), 630 kg (1,389 Lb) filled weight.
• HOLLYWOOD AIRJET S100102 (60059): 1.96 m x 66 cm / 77" x 26", 4-6 persons, 908 L (240 gal), 937 kg (2,066 Lb) filled weight.
• ARUBA AIRJET S100102 (60061): 1.70 m x 66 cm / 67" x 26", 2-3 persons, 605 L (160 gal), 630 kg (1,389 Lb) filled weight.
• MAURITIUS AIRJET S100102 (60067): 2.70 m x 1.80 m x 71 cm / 107" x 71" x 28", 5-7 persons, 1,370 L (362 gal), 1,395 kg (3,076 Lb) filled weight.
• FIJI AIRJET S100102 (60085): 1.80 m x 66 cm / 71" x 26", 2-4 persons, 669 L (177 gal), 696 kg (1,534 Lb) filled weight.

For detailed diagrams and part numbers for your specific model, please refer to the comprehensive resources available on the Bestway support website.

INSTALLATION

SET-UP INSTRUCTION IN WINTER

It is important to follow these suggestions if you are setting up the spa during the winter period. This will prevent damage to the PVC material and extend the life of your product drastically.

• If the ambient temperature is below 10°C (50°F), we suggest keeping the package indoors where the temperature is above 15°C (59°F) for at least 2h before inflation. This will make the spa liner more flexible and easier to set up.
• Open the package in the same room where the temperature is above 15°C (59°F), and inflate the spa using the spa heater.
• Position the spa liner outdoors in the desired position, connect the spa heater and fill with water.

Important: The water temperature used to fill the spa must be above 6°C (42.8°F), otherwise when you begin to operate with the spa heater, the E03 alarm will appear.

Important: If the Freeze Shield™ system isn't working, alarms will pop up on the spa. Be sure to check the status of your spa if the outdoor temperature is below 6°C (42.8°F). In case of a long-term absence from home when there is a risk of temperatures falling below 6°C (42.8°F), we strongly suggest disassembling the spa and storing it following the storage procedure. When you assemble the spa, the automatic warm function will turn on. In this condition, the spa can be used when the temperature is lower than 6°C (42.8°F).

NOTE: The air pressure gauge of the hand pump only shows the air pressure higher than 5 psi, which is normal. When the air pressure in the product is lower than 5 psi, the air pressure gauge will not show a value (Only for drop stitch spa).

Inflation Steps:

1. Unfold the spa liner.
2. Connect the inflation hose to the spa pump and the spa's inflation valve. The pump has a digital display and control buttons.
3. Inflate the spa. For Helsinki models, use the pressure gauge to ensure pressure is between 0.48-0.69 Bar (7-10 PSI). For other models, the pressure is 0.034-0.055 Bar (0.5-0.8 PSI). Inflation takes 3-6 minutes.
4. For Paris, Bali, and Hollywood models, connect the spa pump to the spa liner's inlet/outlet valves. This involves attaching the hose from the pump to the spa's connection points, ensuring a secure fit.
5. Once inflated, ensure the spa is stable and ready for water filling.

SPA PUMP EQUIPOTENTIAL BONDING TERMINAL

It is recommended to arrange for a qualified electrician to connect the spa pump to an equipotential bonding terminal using a minimum 2.5mm² solid copper conductor.

When inflating, you will notice that air will be expelled from the area where the air hose connects to the pump; this is normal for technique requirements.

Important: Don't cover the holes on the base of the inflation hose. This operation will over inflate the liner and damage the structure.

Do not use an air compressor to inflate the pool.

Do not drag the pool on rough ground as this may cause damage to the pool liner.

Inflation time for reference only.

Air Valve Check (for spa with quick inflation/deflation valve)

Always check the air valve carefully before inflation to ensure there is not an air leak. If the air valve is loose, use the provided wrench to fasten the air valve following these steps:

With one hand, hold the backside of the air valve from the inner side of the spa wall and turn the wrench clockwise.

NOTE:

1. Do not over tighten.
2. Do not adjust the air valve connector when the spa is in use.

USING THE SPA

The spa control panel features a digital display and several buttons:

• A. LOCK/UNLOCK BUTTON: The pump has a 5-minute auto-lock. This light will turn on. To lock or unlock the pump, place a finger over the lock/unlock button for 3 seconds.
• B. POWER-SAVING TIMER BUTTON: Designed to help avoid wasting power by setting the time and duration of the heating cycle for the spa. This way, you can enjoy your spa at the time you desire, without needing to leave the heater on at all times.

STEP 1: Set the heating duration

1. Press the ◷ button until the ◷ LED starts to flash.
2. Press the ▲ or ▼ button to adjust the heating duration (From 1-999 hours).
3. Press the ◷ button again to confirm the heating duration.

STEP 2: Set the number of hours FROM NOW when the heater will activate

1. After setting the heating duration, the ◷ LED starts to flash.
2. Press the ▲ or ▼ button to adjust the hours until time of activation (From 0-999 hours).
3. Press ◷ button again or simply touch nothing for 10 seconds to confirm the setting. The ◷ LED will light steadily, and the countdown to heater activation will begin.

To modify the timer settings: Press the ◷ button and use the ▲ or ▼ button to adjust.

Cancel the setting: Press the ◷ button for 2 seconds.

NOTE: After setting, the screen flashes the current temperature and time alternately.

NOTE: Timer adjustment (amount of time with the heater ON) may be set from 1 to 999 hours; Reservation time adjustment (the number of hours FROM NOW when the heater will begin to function) may be set from 0 to 999 hours. If the timer is set at 0 hour, the heating system will activate immediately.

Note that the timer is one time per use - the user sets the duration of the heating cycle, and how many hours from now the heating cycle begins. The timer does NOT repeat until reset.

• C. HEAT BUTTON: Use this button to activate the heating system. When the light above the heat button is red, the heating system is activated. When the light is green, the water is at the set temperature and the heating system is at rest.

NOTE: If the heating system is activated the filtration system will automatically start.

NOTE: After turning off the heating system the filtration system will continue to operate.

NOTE: If the spa heater is on when the water temperature is below 6°C (42.8°F), the heating system will warm the water until 10°C (50°F) automatically.

• D. MASSAGE SYSTEM BUTTON: Use this button to activate the massage system, which has a 30-minute auto-shutoff feature. The light above the Massage System Button displays red when activated.

IMPORTANT: Do not run the Massage system when the cover is attached. Air can accumulate inside the spa and cause irreparable damage to the cover and bodily harm.

NOTE: Heat and massage system work together to create a warm massage experience.

• E/G. TEMPERATURE ADJUSTMENT BUTTONS (▲/▼): Pressing the Temperature Increase or Decrease buttons will cause the LED to flash. When it is flashing you can adjust to the desired temperature setting. If you hold these buttons down the values will rapidly increase or decrease. The new and desired temperature setting will remain on the LED display for 3 seconds to confirm the new value.

NOTE: The default temperature is 35°C (95°F).

NOTE: Temperature adjustment ranges from 20°C (68°F) to 40°C (104°F).

• F. ON/OFF BUTTON (⏻): Press this button for 2 seconds to activate the control panel buttons and the light turns to green. Press this button for 2 seconds to turn off all currently activated functions.
• H. CELSIUS/FAHRENHEIT TOGGLE (°C/°F): The temperature can be displayed in either Fahrenheit or Celsius.
• I. WATER FILTER BUTTON (?): This button turns the filter pump on and off. The light above the Water Filter Button displays red when activated.

POWER-SAVING TIMER LED:

• This flashing LED means you are setting the heating duration. The light will be on when the heating function starts to work.
• This flashing LED means you are setting the number of hours FROM NOW when the heater will activate. When the light is on, the Power-Saving Timer function is set.

NOTE: The WATER HEATER rate may change in the conditions below:

• When the outdoor temperature is below 15°C (59°F).
• If the cover is not in position when the heating function is activated.

NOTE: To display the current water temperature, run the filter system for at least a minute.

The water temperature as tested by an external thermometer may vary from the temperature as displayed on the spa panel by as much as approximately 2°C (35.6°F).

WINTER USE INSTRUCTIONS

The Freeze Shield™ system is indicated by a snowflake icon.

• You can keep the spa on during winter when the temperature is lower than 6°C (42.8°F). The Freeze Shield™ system automatically keeps the water temperature between 6°C (42.8°F) and 10°C (50°F), and it will prevent the water from freezing.

Important: If the water temperature is below 6°C (42.8°F), the spa heater must always be on. In this mode, the Freeze Shield™ system can keep the internal temperature between 6°C (42.8°F) and 10°C (50°F) to prevent damage, such as water freezing in the pipes or the circulation system.

Important: If the Freeze Shield™ system isn't working, alarms will pop up on the spa. Be sure to check the status of your spa if the outdoor temperature is below 6°C (42.8°F). In case of a long-term absence from home when there is a risk of temperatures falling below 6°C (42.8°F), Bestway strongly suggests disassembling the spa and storing it following the storage procedure.

• Any damage as a result of using the spa in these conditions is the responsibility of the customer. Do not use the spa when the ambient temperature reaches -10°C (14°F).

HEATING RESET

When using the Lay-Z-SPA for the first time, or after a long period of inactivity, be sure to press the reset button on the pump using a small and thin object. The reset button is typically recessed and marked

• Google Docs
• Google Drive
• Download [pdf]



File Info : application/pdf, 36 Pages, 4.32MB

Document Document

Related Documents

	Bestway Lay-Z-Spa Owner's Manual: Safety, Setup, and Usage Guide Comprehensive owner's manual for Bestway Lay-Z-Spa models, covering important safety instructions, pre-setup checks, installation, usage, maintenance, troubleshooting, and error codes.
	Lay-Z-Spa Owner's Manual - Bestway Portable Hot Tubs Comprehensive owner's manual for Bestway Lay-Z-Spa portable hot tubs, covering safety instructions, installation, winter setup, operation, maintenance, troubleshooting, and storage. Learn how to safely use and care for your Lay-Z-Spa.
	Bestway Lay-Z-Spa Owner's Manual: Safety, Installation, and Usage Guide A comprehensive guide for Bestway Lay-Z-Spa inflatable hot tubs, covering essential safety instructions, step-by-step installation, operation, maintenance, troubleshooting, and error codes for optimal user experience.
	Bestway Lay-Z-Spa AirJet Series User Manual & Safety Guide Comprehensive user manual and safety guide for Bestway Lay-Z-Spa AirJet series hot tubs. Learn about installation, operation, maintenance, troubleshooting, and safety precautions.
	מדריך למשתמש Bestway Lay-Z-Spa מדריך מקיף למשתמש עבור מערכות הספא Lay-Z-Spa של Bestway, הכולל הוראות התקנה, בטיחות, שימוש ותחזוקה.
	Návod k použití vířivky Bestway Lay-Z-Spa: Bezpečnost, Instalace a Údržba Kompletní uživatelská příručka pro vířivky Bestway Lay-Z-Spa, která obsahuje důležité bezpečnostní pokyny, návod k instalaci, používání, údržbě a řešení problémů.
	Bestway SaluSpa Owner's Manual: Setup, Use, and Maintenance Guide Comprehensive owner's manual for Bestway SaluSpa inflatable hot tubs, covering setup, operation, maintenance, safety, and troubleshooting for models like Miami, Cancun, and Hawaii AirJet.
	Bestway Lay-Z-Spa Manual: Safety, Setup & Models 54112-54156 Official Bestway Lay-Z-Spa manual covering safety, installation, maintenance, and specifications for models 54112 (Vegas), 54113 (Monaco), 54123 (Miami), 54129 (Palm Springs), 54148 (Paris), 54154 (Hawaii), and 54156 (Siena). Learn how to set up and enjoy your spa safely.