PawHut Assembly & Instruction Manual
Model: INdcd040V01_GL, D51-009
Important Information
Please retain this manual for future reference. Read carefully before assembly.
Safety Warnings:
- This product must be assembled by an adult.
- Do not over-torque screws and bolts.
- Do not install in flammable places or in case of fire.
- Use the product on a flat, stable ground.
Parts List
| Identifier | Description | Quantity |
|---|---|---|
| A | Side Panel | 1 |
| B | Side Panel | 1 |
| C | Side Support | 4 |
| D | Back Panel | 1 |
| E | Base/Top Panel | 1 |
| F | Side Panel | 1 |
| G | Base Frame Component | 1 |
| H | Base Frame Component | 1 |
| I | Divider/Shelf | 1 |
| J | Divider/Shelf | 1 |
| K | Base Frame Component | 1 |
| L | Base Frame Component | 1 |
| M | Internal Shelf/Support | 1 |
| N | Top Panel | 1 |
| O | Handle/Support Piece | 1 |
| P | Feet/Decorative Elements | 2 |
| Q | Door/Drawer Front | 1 |
| R | Door/Drawer Runner/Support | 1 |
| S | Internal Shelf/Support | 1 |
| T | Side Panel | 1 |
Hardware List
| Identifier | Size/Type | Quantity |
|---|---|---|
| S1 | 3.5*40mm Screw | 2 |
| S2 | 3.5*25mm Screw | 8 (+1 extra) |
| S3 | 3.5*20mm Screw | 26 (+2 extra) |
| S4 | 3.0*18mm Screw | 11 (+1 extra) |
| S5 | 3.0*12mm Screw | 6 (+1 extra) |
| S6 | 2.5*10mm Screw | 48 (+2 extra) |
| S7 | Dowel/Connector | 4 |
| S8 | Dowel/Connector | 2 |
| S9 | Dowel/Connector | 2 |
| S10 | Dowel/Connector | 2 |
| S11 | Dowel/Connector | 4 |
Assembly Steps
Step 01
Attach part A to two pieces of part C using four S3 screws.
Diagram shows part A positioned horizontally, with two C pieces attached vertically to its sides, secured by S3 screws.
Step 02
Attach part B to two pieces of part C using four S3 screws.
Diagram shows part B positioned horizontally, with two C pieces attached vertically to its sides, secured by S3 screws.
Step 03
Attach part G to part K using two S3 screws and one S8 screw. Then, attach part I to part G using four S6 screws and two S7 connectors.
Diagram shows G and K forming a base structure. Part I is then fitted into G and secured.
Step 04
Attach part H to part J using two S3 screws and one S8 screw. Then, attach part L to part J using four S6 screws and two S7 connectors.
Diagram shows H and J forming a base structure. Part L is then fitted into J and secured.
Step 05
Attach part F to part T using two S11 screws. Repeat for the second set of F and T panels.
Diagram shows two separate sub-assemblies, each consisting of a panel F attached to a panel T using S11 screws.
Step 06
Attach part E to the main structure using two S3 screws and one S9 connector.
Diagram shows part E being attached to a larger assembly, likely as a base or top, secured by S3 and S9.
Step 07
Attach part D (back panel) to the main structure using eight S3 screws.
Diagram shows the back panel D being attached to the partially assembled unit using S3 screws.
Step 08
Attach part S to part M using two S10 connectors. Then, attach the M/S assembly to the main structure using eight S6 screws and eight S2 screws.
Diagram shows an internal shelf/support M with S attached, then being installed into the main body using S6 and S2 screws.
Step 09
Attach part Q (door/drawer front) to the main structure using two S1 screws.
Diagram shows part Q being attached to the front of the unit, likely as a door, secured by S1 screws.
Step 10
Attach part O to part N using three S5 screws. Then, attach part P (x2) to the top of the unit using eleven S4 screws.
Diagram shows the top panel N with O attached. Then, two P pieces are attached to the top surface, secured by S4 screws. The "Done" label indicates completion.
