Lost Vape Centaurus M200 User Manual
Product Overview
This document provides instructions and information for the Lost Vape Centaurus M200 vaping device, covering its features, operation, and safety guidelines.
Main Features
- QUEST 2.0 CHIP
- 200W MAX OUTPUT POWER
- 18650 DUAL BATTERIES (Not Included)
- TYPE-C FAST CHARGING
Basic Parameters
| Parameter | Value |
|---|---|
| Dimension | 93mm × 56.7mm × 26mm |
| Weight | 152 ± 5g |
| Battery | Dual 18650 Battery (Not Included) |
| Input Voltage | 6.0V - 8.4V |
| Battery Voltage | 3.0V - 4.2V |
| Output Voltage | 0.7V - 10V |
| Power Range | 5W - 200W |
| Input Current | 1A - 40A |
| Screen Pixel | 0.96" 80*160 |
| Body Material | Aluminium-Alloy & Stainless Steels |
Components Overview
The device features the following components:
- Battery Cover
- Switch Button: Press [Right] to TURN ON, [Left] to TURN OFF.
- Fire Button
- Indicator: LED indicators display battery status.
- 0.96" TFT Display Screen
- 360° Rotation Button: Used for power adjustment.
- 510 Connector
- Type-C Port
Basic Operation
Turn On/Turn Off
To turn the device ON, press the Switch Button to the [Right]. To turn it OFF, press the Switch Button to the [Left].
Puff Time Display & Puff Count Reset
- The Puff Time is displayed after each vaping session.
- To reset the puff count, ensure the device is in the power-off state. Then, press the Fire Button and simultaneously turn on the Switch Button.
Check the Battery Level
LED indicators will flash during vaping or charging to show the remaining battery capacity. The general indications are:
- 0% - 20%
- 20% - 40%
- 40% - 60%
- 60% - 80%
- 80% - 100%
Note: Specific LED color patterns are not detailed in the provided text.
How to Adjust Wattage
Turn the 360° Rotation Button to enter power adjustment mode. Rotating the button clockwise increases the power incrementally. The steps are:
- 0-39W: 1W increments
- 40W-98W: 2W increments
- 100W-195W: 5W increments
Wattage can be adjusted cyclically between a minimum of 5W and a maximum of 200W.
Switch Between Modes
- To Lock/Unlock the Output Power, press the Fire button 3 times consistently within 2 seconds. The Fire button will remain functional for activation even when locked.
- To switch between Normal Mode and RDA DIY Mode, press the Fire button 5 times while the power is unlocked.
Description of Warning Messages
The device may display the following warning messages:
- Low Battery: Indicates battery voltage is below 3.3V before use or below 2.85V during use. This message will persist for a few seconds after attempting to fire. Please replace the battery.
- Check Atomizer: Signifies that no atomizer is detected, or the atomizer's resistance is higher than 5Ω.
- Short Circuit: Indicates the atomizer's resistance is lower than 0.08Ω.
- Too Hot: The device will shut down if the internal board temperature exceeds 85℃. Normal operation can resume once the temperature returns to 65℃.
- Over 10s: The output will automatically cut off, and the screen will display "Over 10s" if vaping continues for more than 10 seconds consecutively.
Safety Warnings
- Warning For Vulnerable Consumer Groups: This product is not recommended for minors, pregnant or breast-feeding women, or individuals at risk of heart disease, depression, and asthma.
- Battery Caution: Do not expose the device to extreme temperatures. Do not disassemble the device without explicit recommendation from Lost Vape.
- Warranty: The device is covered by a 3-month warranty from the date of purchase.
- Contacts: For additional questions or inquiries, please contact Lost Vape via email at support@lostvape.com or visit their website: www.lostvape.com.
