SHADA 310701 LED Floodlight

Safety Warnings

⚠️ General Warnings:

• Read and understand all instructions before installation or use.
• Keep this document for future reference.
• Use the product only as described.
• Other uses may damage the product or cause injury (short circuit, fire, electric shock).
• Disconnect from power if problems occur.
• Do not drop or bump the product.
• Do not use if a part is damaged or defective; replace immediately.
• Non-standard electrical installations require a qualified technician to reduce shock risk.
• Ensure sufficient ventilation during use.
• Never cover electrical (LED) devices during use, as they can generate heat.
• LEDs are extremely bright; do not stare directly at them to avoid serious eye damage.
• Product use (indoor/outdoor) will be specified on the product or in the manual.
• Keep out of reach of children and animals.

⚡ Risk of Electric Shock: Ensure all electrical work is performed by qualified personnel.

⚠️ Note on Warranty: Opening the device voids the warranty.

Installation Instructions

Step 1: Mounting Preparation

Diagram Description: Shows the rear of the LED light fixture with mounting points. A warning symbol ⚠️ is present. Text indicates "OFF".

Prepare the mounting location. Ensure the power is OFF.

Step 2: Wall Mounting

Diagram Description: Shows drilling holes into a brick wall and inserting wall plugs. A measurement "MIN. 35cm" is indicated.

Drill holes in the wall and insert appropriate wall plugs. Ensure a minimum distance of 35cm from other fixtures or surfaces if applicable.

Step 3: Attaching Fixture to Wall

Diagram Description: Shows the LED fixture being attached to the wall using screws.

Securely attach the LED fixture to the wall using screws.

Step 4: Connecting Power Cable

Diagram Description: Shows the fixture with a cable entry point. An arrow indicates where the power cable should be fed through.

Feed the power cable through the designated entry point on the fixture.

Step 5-10: Wiring the Power Supply

Diagram Description (Steps 5-10): A series of diagrams showing the connection of wires (Live, Neutral, Earth) from the power cable to the internal terminals of the fixture. Different wire colors (brown, blue, green/yellow) are shown. A junction box or connector is depicted.

Connect the power supply wires to the corresponding terminals inside the fixture. Typically, this involves connecting the Live wire (e.g., brown), Neutral wire (e.g., blue), and Earth wire (e.g., green/yellow) to their respective terminals. Ensure secure connections. [Diagram shows wire stripping and insertion into connectors].

Step 11-13: Final Assembly and Testing

Diagram Description (Step 11-12): Shows the cable gland being tightened to secure the cable and seal the entry point.

Diagram Description (Step 13): Shows the fixture being adjusted, and a final check with a warning symbol ⚠️ and a "NO" symbol next to a lightning bolt, followed by "ON" and "OFF" switches.

Secure the cable gland to seal the entry point. Adjust the fixture angle as needed. Test the light by switching it ON. Ensure it operates correctly and all safety checks are passed. [Diagram shows the light turning ON].

LED Module Replacement

⚠️ Important: Replace the LED module only with qualified personnel. Opening the device voids the warranty.

Procedure

Diagram Description (Steps 1-3): Shows the rear of the fixture and the LED module. Warnings about qualified personnel and warranty are prominent.

Diagram Description (Steps 4-8): Shows how to open the fixture, potentially by removing screws or clips, and accessing the internal components including the LED module and driver.

Diagram Description (Steps 9-16): Illustrates disconnecting the old LED module and driver, and connecting the new ones. Specific wire connections are shown. The term "optional" appears for some components.

Diagram Description (Steps 17-19): Shows the process of removing the old module and installing the new one.

Diagram Description (Steps 20-21): Shows final assembly, sealing, and a warning symbol ⚠️ with "NO" and "YES" symbols related to incorrect/correct procedures.

To replace the LED module, first ensure the power is disconnected and the device has cooled down. Carefully open the fixture following the diagrams, which may involve removing screws or clips. Disconnect the old LED module and driver. Connect the new LED module and driver according to the wiring diagram provided. Ensure all connections are secure and the fixture is properly sealed upon reassembly. Refer to specific diagrams for detailed connection points and component handling. [Diagrams show disconnection, connection, and reassembly steps].

Cleaning and Maintenance

Do not use cleaning solvents or abrasives.

Do not clean the inside of the device.

Do not attempt to repair the device if it does not function correctly; replace it.

Clean the outside of the device using a soft, damp cloth. Do not use a microfiber cloth.

Support

For further assistance, comments, or suggestions, please visit: www.shada.nl/nl/contact

Compliance and Disposal

Energy Efficiency: This product contains a light source of energy efficiency class E.

CE Marking: This product carries the CE mark, confirming compliance with EU safety, health, and environmental protection requirements.

Disposal: The item should be disposed of separately from household waste. Hand it in for recycling according to local environmental regulations. This helps reduce waste sent to incinerators or landfills and minimizes potential negative environmental and health impacts. ♻️

Declaration of Conformity (D.O.C.): shada.nl/p/310701

Manufacturer/Distributor:

• SHADA
• Molenmakershoek 28, NL-7328 JK APELDOORN - The Netherlands
• www.shada.nl

WEEE Registration Numbers: NL: 3505, DE: 37281017, AT: 40133, ES: 7020