Kogan Mobile TV Floor Stand
Model: KATVSFWS86A
Suitable For: 37-86" TVs
Safety & Warnings
Read the entire user guide before starting installation and assembly. Contact your local distributor for assistance with any questions regarding instructions or warnings.
CAUTION: Using products heavier than the rated weights may result in instability and possible injury.
- Follow assembly instructions closely. Improper installation can lead to damage or serious personal injury.
- Use safety gear and proper tools. This product should only be installed by professionals.
- This product is designed for installation on solid concrete walls, masonry walls, or wood stud walls.
- Ensure the supporting surface can safely support the combined weight of the equipment and all attached hardware and components.
- Use the provided mounting screws and DO NOT OVERTIGHTEN them.
- This product contains small items that could be a choking hazard if swallowed. Keep away from children.
- This product is intended for indoor use only. Outdoor use could lead to product failure and personal injury.
- Never exceed the maximum load capacity of 50kg (TV) or 5kg (media shelves), as this may result in product failure or personal injury.
IMPORTANT: Verify all parts against the component checklist before installation. Contact your place of purchase for replacements if any parts are missing or faulty.
MAINTENANCE: Regularly check that the product is secure and safe to use (at least every three months).
VESA Compatibility: 200x200, 300x200, 400x200, 300x300, 400x300, 400x400, 400x600
Max Load: 86" TV, 50kg/110lbs (TV), 5kg/11lbs (DVD/Media Shelves)
Components
Please refer to the diagrams for visual identification of components:
- A (x1) - Base
- B (x1) - Lower Pole
- C (x1) - Upper Pole
- D (x1) - Media Shelf
- E (x1) - Shelf Bracket
- F (x1) - TV Brackets
- G (x1) - Backing Plate
- H (x2) - Mounting Arms
- I (x4) - Wheel Locks
- J (x5) - Cable Ties
- K (x2) - M6x8 Screws
- L (x2) - M6x8 Screws
- M (x4) - M6x12 Screws
- N (x4) - M6x16 Screws
- O (x3) - M8x20 Hex Screws
- P (x2) - M8x75 Hex Screws
- Q (x3) - D8 Washers
- R (x2) - M8 Nuts
- S (x1) - Allen Key 3mm
- T (x1) - Allen Key 4mm
- U (x1) - Allen Key 6mm
- V (x1) - Open Spanner 10-13mm
- M-A (x4) - M6x14 Screws
- M-B (x4) - M8x16 Screws
- M-C (x4) - M6x30 Screws
- M-D (x4) - M8x35 Screws
- M-E (x4) - D8 Washers
- M-F (x4) - Spacers
- M-G (x4) - Spacers
Assembly Instructions
Step 1: Attach the lower pole (B) to the base (A). 2 people recommended.
Diagram shows base (A) with wheels, lower pole (B) being attached with screws and washers using Allen key (U).
Step 2: Insert the upper pole (C) into the lower pole (B) and secure with M6x8 screws (K) using Allen key (S).
Diagram shows upper pole (C) sliding into lower pole (B), with close-up of screws (K) being tightened with Allen key (S).
Step 3: Attach the media shelf bracket (E) to the upper pole (C) using M6x16 screws (N) and Allen key (T). Then attach the media shelf (D) to the bracket (E) using screws.
Diagram shows bracket (E) being attached to pole (C), and shelf (D) being attached to bracket (E).
Step 4: Attach the TV brackets (F) to the upper pole (C) using M8x75 hex screws (P), M8 nuts (R), and open spanner (V). Ensure the brackets are oriented correctly.
Diagram shows TV brackets (F) being attached to the upper pole (C) with screws (P) and nuts (R).
Step 5: Align the mounting arms (H) with your TV's VESA holes. Secure using the appropriate screws (M-A, M-B, M-C, M-D), washers (M-E), and spacers (M-F, M-G) based on the TV's depth. Ensure correct screw length is used (not too long, not too short).
Diagram shows mounting arms (H) attached to the back of a TV, with a selection of screws and spacers shown.
Step 6: Mount the TV with the attached brackets onto the floor stand. 2 people recommended for carrying the TV to prevent damage.
Diagram shows two people lifting a TV with brackets attached onto the floor stand.
Step 7: Secure the TV brackets to the floor mount using the 4 M6x12 screws (M).
Diagram shows close-up of the TV brackets being secured to the mount with screws (M).
Step 8: Adjusting the Vertical Tilt
Loosen the 4 Allen screws slightly and adjust the vertical tilt of the TV. If the display does not stay in position, adjust the screws as needed.
Diagram shows arrows indicating the adjustment of tilt screws on the TV mount. Another diagram shows a TV being tilted.
Step 9: Rotating the TV (Portrait/Landscape mode)
- To keep the TV in landscape mode, secure it with the 2 M6x8 screws (L).
- To switch to portrait mode, rotate the TV 90° and secure it with the 2 M6x8 screws (L).
Diagrams show the TV being rotated and secured in both landscape and portrait orientations using screws (L).
Step 10: Secure the backing plate (G) to the upper pole (C) using the 2 M6x16 screws (N) and Allen key (T).
Diagram shows the backing plate (G) being attached to the rear of the upper pole (C).
Step 11: Use the cable ties (J) to secure a power board or other accessories to the backing plate (G) on the rear of the TV. Route cables through the floor mount's vertical stand.
Diagram shows cable ties (J) securing cables to the backing plate (G) and routing them down the pole.
