Introduction
This document provides a quick start guide for the Behringer NEKKST series studio monitors (K8, K6, K5) and the K10S studio subwoofer.
NEKKST K8/K6/K5 Studio Monitors
Audiophile Bi-Amped 8", 6", and 5" Studio Monitors with Advanced Waveguide Technology.
NEKKST K10S Studio Subwoofer
Audiophile 10" Studio Subwoofer with High Excursion Woofer.
Step 1: Hook-Up
This section outlines the basic connections required to set up your NEKKST system.
General Placement Advice:
- Place the monitor speakers at head level, unobstructed, and at equal distances to the left and right of your listening position to form an equilateral triangle.
- For the K10S subwoofer, experiment with its position, such as in corners or near walls, to find the best bass response.
Connection Steps:
- Connect the included power cables to each monitor and the subwoofer. Plug the other ends into a mains outlet properly configured for your models. Ensure all equipment is connected to the same outlet if possible to avoid ground loops. DO NOT turn the power on yet.
- Connect your audio source(s) to the inputs of the monitors and subwoofer.
- For mixers, balanced outputs are preferable.
- Audio outputs from a computer can be connected using an interface (e.g., FCA1616).
- Refer to the hook-up diagrams for specific connection ideas using various audio sources like guitars, keyboards, and drum machines.
- Turn on your audio source (mixer, computer, etc.) with the volume set to minimum.
- Turn on the power to each monitor and the subwoofer using their rear panel power switches.
Step 2: Controls
Familiarize yourself with the controls on your NEKKST monitors and subwoofer.
NEKKST K5/K6/K8 Monitor Controls:
- HIGH FREQUENCY: Compensates for room acoustic absorption.
- LOW FREQUENCY: Adapts the monitor for use with a subwoofer or emulates smaller speaker characteristics.
- ROOM COMPENSATION: Provides low-frequency roll-off to compensate for monitor placement (e.g., near walls).
- INPUT TRIM: Adjusts the monitor's input sensitivity to the audio source signal.
- INPUT: Connect audio sources via XLR, RCA, or 1/4" cables.
- POWER SWITCH: Turns the unit on and off. The Behringer logo lights up when powered on.
- POWER SOURCE: Connect the included power cable here and to a mains outlet.
NEKKST K10S Subwoofer Controls:
- LEVEL: Adjusts the subwoofer's input sensitivity to the audio source signal.
- CROSSOVER: Adjusts the crossover frequency to match the K5, K6, or K8 monitors or other system speakers.
- PHASE: Reverses the output phase to compensate for frequency cancellation between the subwoofer and monitors.
- LINE IN (RCA): Connect unbalanced RCA cables for audio sources. The subwoofer sums left and right inputs to mono.
- LINE OUT (RCA): Sends full-range copies of the unbalanced RCA input signal.
- BALANCED INPUTS (XLR): Connect audio sources via XLR cables. The subwoofer sums left and right inputs to mono.
- BALANCED OUTPUTS (XLR): Send full-range copies of the balanced XLR input signal.
Step 3: Getting Started
Follow these steps to set up and achieve optimal sound:
- Position the monitor speakers as described in Step 1 (head level, equal distance).
- Position the K10S subwoofer, experimenting with placement for best bass.
- Connect all audio sources and power cables as per Step 1. Ensure power is off.
- Turn on the audio source (mixer/computer) with volume at minimum.
- Turn on the monitors and subwoofer.
- Set the INPUT TRIM on each monitor to the center (0 dB) position.
- Set the K10S subwoofer's LEVEL knob to the center (0 dB) position. Adjust the CROSSOVER knob to match your monitors.
- Start playing your audio source and slowly increase the volume to a comfortable listening level.
- Adjust the monitor's INPUT TRIM and the subwoofer's LEVEL knobs as needed to achieve a good overall balance.
Specifications
| Feature | K8 | K6 | K5 | K10S |
|---|---|---|---|---|
| Amplifiers | ||||
| Maximum output power | 150 W* | 150 W* | 150 W* | 300 W* |
| Configuration | Bi-amping | Bi-amping | Bi-amping | Mono |
| Type | Class-D | Class-D | Class-D | Controlled limiter |
| Overload protection | Dual-controlled limiter | Dual-controlled limiter | Dual-controlled limiter | |
| Crossover type | Active | Active | Active | 40 to 150 Hz variable |
| Crossover frequency | 3 kHz fixed | 3.2 kHz fixed | 3.2 kHz fixed | |
| Audio Connections | ||||
| Inputs | 1 x XLR, balanced 1 x 1/4" TRS, balanced 1 x RCA, unbalanced |
1 x XLR, balanced 1 x 1/4" TRS, balanced 1 x RCA, unbalanced |
1 x XLR, balanced 1 x 1/4" TRS, balanced 1 x RCA, unbalanced |
2 x XLR balanced inputs 2 x XLR balanced thru outputs 2 x RCA unbalanced inputs 2 x RCA unbalanced thru outputs |
| Max. input level | 14 dBu | 14 dBu | 14 dBu | 20 dBu |
| Controls | ||||
| Volume | N/A | N/A | N/A | -∞ dB to 10 dB |
| Input trim | -6 dB to +6 dB | -6 dB to +6 dB | -6 dB to +6 dB | N/A |
| Low frequency | 0/-2/-4/-6 dB @ 60 Hz, switchable | 0/-2/-4/-6 dB @ 300 Hz, switchable | 0/-2/-4/-6 dB @ 300 Hz, switchable | N/A |
| Room compensation | 0/+2/-2/-4 dB @ 8 kHz, switchable | 0/+2/-2/-4 dB @ 8 kHz, switchable | 0/+2/-2/-4 dB @ 8 kHz, switchable | N/A |
| High frequency | N/A | N/A | N/A | N/A |
| Phase Correction | N/A | N/A | N/A | 0/-180 degrees |
| Loudspeaker System Data | ||||
| Type | 1" tweeter 8" woofer |
1" tweeter 6" woofer |
1" tweeter 5.25" woofer |
10" woofer |
| Frequency response | 40 Hz to 20 kHz | 40 Hz to 20 kHz | 50 Hz to 20 kHz | 40 Hz to 150 Hz |
| Max. sound pressure level | Maximum 102 dB SPL @ 1 m | Maximum 101 dB SPL @ 1 m | Maximum 100 dB SPL @ 1 m | Maximum 117 dB SPL @ 1 m |
| Physical | ||||
| Enclosure | Baffle: Painted injection-molded PC and ABS Enclosure: Matte black PVC laminated 15 mm MDF |
Baffle: Painted injection-molded PC and ABS Enclosure: Matte black PVC laminated 15 mm MDF |
Baffle: Painted injection-molded PC and ABS Enclosure: Matte black PVC laminated 15 mm MDF |
Baffle: Painted injection-molded PC and ABS Enclosure: Matte black PVC laminated 15 mm MDF |
| Grille | N/A | N/A | N/A | Powder-coated galvanized perforated steel mesh grille |
| Power Supply / Voltage (Fuses) | ||||
| Type | Switch mode power supply | Switch mode power supply | Switch mode power supply | Switch mode power supply |
| Voltage | 100-240 VAC, 50/60 Hz | 100-240 VAC, 50/60 Hz | 100-240 VAC, 50/60 Hz | 100-240 VAC, 50/60 Hz (T 2.5 AH 250 V) |
| Power consumption @ 1/8 max power | 40 W | 40 W | 40 W | 50 W |
| Mains connection | Standard IEC connector | Standard IEC connector | Standard IEC connector | Standard IEC connector |
| Dimensions / Weight | ||||
| Dimensions (H x W x D) | 393 x 261 x 315 mm (15.5 x 10.3 x 12.4") |
340 x 230 x 289 mm (13.4 x 9.1 x 11.4") |
288 x 197 x 247 mm (11.3 x 7.8 x 9.7") |
394 x 356 x 404 mm (15.5 x 14.0 x 15.9") |
| Weight | 8.7 kg (19.2 lbs) | 7 kg (15.4 lbs) | 5 kg (11 lbs) | 17.4 kg (38.4 lbs) |
*Independent of limiters and driver protection circuits
Important Information & Safety
Please read the following important information and safety guidelines:
- Electrical Safety: Terminals marked with a symbol (⚡) carry sufficient electrical current to pose a risk of electric shock. Use only high-quality professional speaker cables. Do not remove covers; refer servicing to qualified personnel.
- Moisture and Heat: Do not expose the apparatus to rain or moisture. Avoid placing liquids on the unit. Do not install near heat sources.
- Servicing: All servicing should be performed by qualified service personnel only.
- Ventilation: Do not block ventilation openings.
- Power Cord: Protect the power cord from damage. Ensure it is properly grounded.
- Disposal: This product must not be disposed of with household waste. Follow WEEE Directive guidelines for recycling.
- Battery Disposal: Dispose of batteries at designated collection points, considering environmental aspects.
- Operating Climate: The apparatus can be used in tropical and moderate climates up to 45°C.
- FCC Compliance: This equipment complies with FCC Rules Part 15 for Class B digital devices, designed to provide reasonable protection against harmful interference.
- EU Compliance: The product complies with relevant EU directives (e.g., 2014/35/EU, 2014/30/EU, 2011/65/EU, 2012/19/EU).
Legal Disclaimer: Music Tribe accepts no liability for loss resulting from reliance on the information provided. Specifications are subject to change without notice.
Limited Warranty: For warranty terms and conditions, please visit musictribe.com/warranty.
Music Tribe
Music Tribe
