SFP-5UD/SFP-10UD(E) Five Zone Fire Alarm Control Panel / Ten Zone Fire Alarm Control Panel

General

The SFP-5UD is a five-zone FACP, and the SFP-10UD(E) is a ten-zone FACP. These control panels offer reliable fire signaling protection for small to medium-sized commercial, industrial, and institutional buildings. Both panels feature built-in communicators for Central Station Service and remote upload/download capabilities.

Compatibility includes System Sensor's microprocessor-based i3 series detectors, which can transmit maintenance trouble signals for cleaning needs and supervisory "freeze" signals for low ambient temperatures. The panels also support conventional input devices such as two- and four-wire smoke detectors, pull stations, waterflow devices, tamper switches, and other normally-open contact devices. Refer to the Notifier Device Compatibility Document for a complete list of compatible devices.

Outputs include four Notification Appliance Circuits (NACs), three programmable Form-C relays (factory programmed for Alarm, Trouble, and Supervisory), and 24 VDC special application resettable and nonresettable power outputs. All wiring, AC voltage, battery level, and telephone line integrity are supervised.

Activation of a compatible smoke detector or any normally-open fire alarm initiating device triggers audible and visual signaling devices, illuminates an indicating LED, sounds the piezo sounder at the FACP, activates the communicator and FACP alarm relay, and operates an optional module for remote station notification or auxiliary control functions.

The FireWatch Series internet monitoring modules, IPDACT-2 and IPDACT-2UD, allow alarm signal monitoring over the Internet, potentially saving costs on dedicated telephone lines. A secondary telephone line can be retained for backup communication over the public switched telephone line.

Note: The SFP-10UDE offers the same features as the SFP-10UD but connects to 240 VAC. Unless otherwise specified, information in this data sheet applies to both 120 VAC and 240 VAC versions.

Note: For ULC-listed models, refer to document dn-60437.

Features

• Listed to UL Standard 864, 9th edition.
• Built-in DACT (Digital Alarm Communicator/Transmitter).
• Style B (Class B) IDC (Initiating Device Circuit):
  • SFP-5UD: five IDCs.
  • SFP-10UD: ten IDCs.
• Style Y (Class B) NAC (Notification Appliance Circuit) - special application power:
  • SFP-5UD: four NACs.
  • SFP-10UD: four NACs.
• Notification Appliances may be programmed for:
  • Silence Inhibit.
  • Auto-Silence.
  • Strobe Synchronization for System Sensor, Wheelock, Gentex, Faraday, or Amseco devices.
  • Selective Silence (horn-strobe mute).
  • Temporal or Steady Signal.
  • Silenceable or Nonsilenceable.
• Optional N-CAC-5X Style Z (Class A) Converter Module for NACs and IDCs (2 required for SFP-10UD).
• Form-C Relays for Alarm, Trouble, and Supervisory - Contact Ratings: 2.0 A @ 30 VDC or 30 VAC (resistive).
• Total system current: 3.0 A for SFP-5UD; 7.0 A for SFP-10UD.
• Optional Dress Panel DP-51050 (red) or DP-51050B (black).
• Optional Trim Ring TR-CE/-B for semi-flush mounting.
• 24 volt operation.
• Low AC voltage sense.
• Alarm Verification.
• PAS (Positive Alarm Sequence).
• Automatic battery trickle charger.
• Up to eight ANN-BUS annunciators supported.
• Optional modules:
  • 8 zone Relay Module N-ANN-RLY.
  • LED Annunciator Module N-ANN-LED.
  • Remote LCD Annunciator N-ANN-80.
  • Remote Printer Gateway N-ANN-S/PG.
  • LED Annunciator Driver N-ANN-I/O.
  • 4XTM module (conventional reverse polarity/city box transmitter).

Programming and Software

• Programmable at the panel without special software or additional equipment.
• Programmable Make/Break Ratio.
• Upload/Download (local or remote) of program and data via integral DACT.

User Interface

• Built-in DACT (Digital Alarm Communicator/Transmitter).
• Integral 80-character LCD display with backlighting and keypad.
• Real-time clock/calendar with automatic daylight savings adjustments.
• ANN-BUS for connection to remote annunciators.
• Audible or silent walk test capabilities.
• Piezo sounder for alarm, trouble, and supervisory notifications.

Controls and Indicators

LED Indicators

• FIRE ALARM (red LED)
• SUPERVISORY (yellow LED)
• TROUBLE (yellow LED)
• AC POWER (green LED)
• ALARM SILENCED (yellow LED)

Control Buttons

• ACKNOWLEDGE button
• ALARM SILENCE button
• SYSTEM RESET (lamp test) button
• DRILL button

Terminal Blocks

AC Power (TB1)

• SFP-5UD (FLPS-3 Power Supply): 120 VAC, 50/60 Hz, 1.00 A.
• SFP-10UD (FLPS-7 Power Supply): 120 VAC, 50/60 Hz, 3.8 A.
• SFP-10UDE (FLPS-7 Power Supply): 240 VAC, 50 Hz, 2.20 A.
• Wire size: minimum 14 AWG (2.00 mm²) with 600 V insulation. Supervised, nonpower-limited.

Battery (J12)

• Maximum Charging Circuit - Normal Flat Charge: 27.6 VDC @ 1.4 A. Supervised, nonpower-limited.
• Maximum Charger Capacity: 18 AH battery for SFP-5UD, and 26 AH battery for SFP-10UD(E). [Two 18 Ah batteries can be housed in the FACP cabinet. Larger batteries require a separate battery box such as the BB-26 or NFS-LBB.]
• Minimum Battery Size: 7 AH.

Initiating Device Circuits (TB4 and TB 6 on SFP-10UD only)

• Alarm Zones 1 - 5 on TB 4 (SFP-5UD and SFP-10UD).
• Alarm Zones 6 - 10 on TB6 (SFP-10UD only).
• Supervised and power-limited circuitry.
• Operation: All zones Style B (Class B).
• Normal Operating Voltage: Nominal 20 VDC.
• Alarm Current: 15 mA minimum.
• Short Circuit Current: 40 mA maximum.
• Maximum Loop Resistance: 100 ohms.
• End-of-Line Resistor: 4.7K ohm, 1/2 watt (P/N 71252 UL-listed).
• Standby Current: 2 mA.
• Refer to the Notifier Device Compatibility Document for listed compatible devices.

Notification Appliance Circuits (TB5 and TB 7 on SFP10UD only)

• Four NACs.
• Operation: Style Y (Class B).
• Special Application power.
• Supervised and power-limited circuitry.
• Normal Operating Voltage: Nominal 24 VDC.
• Maximum Signaling Current: 3.0 A for SFP-5UD, 2.5 A maximum per NAC; 7.0 A for SFP-10UD(E), 3.0 A maximum per NAC.
• End-of-Line Resistor: 4.7K ohm, 1/2 watt (Part #71252).
• Max. Wiring Voltage Drop: 2 VDC.
• Refer to the Notifier Device Compatibility Document for compatible listed devices.

Form C Relays (TB8)

• Relay 1 (factory default programmed as Alarm Relay).
• Relay 2 (factory default programmed as fail-safe Trouble Relay).
• Relay 3 (factory default programmed as Supervisory Relay).

Special Application Resettable Power (TB9)

• Jumper selectable by JP31 for resettable or nonresettable power.
• Operating voltage: 24 VDC nominal.
• Maximum available current: 500 mA - appropriate for powering four-wire smoke detectors.
• Power-limited circuit.
• Refer to the Notifier Device Compatibility Document for listed compatible devices.

Remote Sync Output (TB2)

• Remote power supply synchronization output, only required for the SFP-5UD.
• 24 VDC nominal special application power.
• Maximum current is 40 mA.
• End-of-Line Resistor: 4.7K ohm.
• Supervised and power-limited circuit.

Product Line Information

• SFP-5UD: Five-zone, 24-volt Fire Alarm Control Panel (includes black backbox, FLPS-3 power supply, technical manual, and a frame & post operating instruction sheet).
• SFP-5UDR: Same as SFP-5UD but in a red backbox.
• SFP-10UD: Ten-zone, 24-volt Fire Alarm Control Panel (includes black backbox, FLPS-7 power supply, technical manual, and a frame & post operating instruction sheet).
• SFP-10UDE: Same as SFP-10UD but with a 220 VAC power supply (FLPS-7).
• SFP-10UDR: Same as SFP-10UD but in a red backbox.

Internet Monitoring Modules

• IPDACT, IPDACT-2/2UD: Internet Monitoring Module. Mounts in the bottom of the enclosure with optional mounting kit (PN IPBRKT). Connects to primary and secondary DACT telephone output ports for internet communications over a customer-provided Ethernet internet connection. Requires a compatible Teldat Visoralarm Central Station Receiver. Can use DHCP or static IP. (See data sheet DN-60389 for more information.)
• IPBRKT: Mounting kit for IPDACT in a common enclosure.
• IPSPLT: Y Adaptor option to allow connection of both panel dialer outputs to one cable input to IPDACT (sold separately).

Optional Modules

• N-CAC-5X: Optional (Class A) Converter Module. Converts Style B (Class B) Initiating Device Circuits to Style D (Class A); and Style Y (Class B) Notification Appliance Circuits to Style Z (Class A). Connects to J2 on the SFP-5UD and SFP-10UD main circuit board and to J7 on the SFP-10UD. Note: Two Class A Converter Modules are required for the ten-zone panel.
• 4XTM: Transmitter module. Provides a supervised output for local energy municipal box transmitter and alarm and trouble reverse polarity. Includes a disable switch and disable trouble LED. A module jumper option allows the reverse polarity circuit to open with a system trouble condition if no alarm conditions exist. Mounts to the main circuit board connectors J4 and J5.

Compatible Annunciators

• N-ANN-80: Remote LCD Annunciator. Mimics the information displayed on the FACP's LCD. Available in black (N-ANN-80) or white (N-ANN-80-W).
• N-ANN-LED: LED Annunciator with three LEDs for each zone: Alarm, Trouble, and Supervisory. Includes black backbox. Available in black (N-ANN-LED), white (N-ANN-80-W), or red (N-ANN-80-R).
• ANN-RLED: LED Annunciator with three alarm (red) indicators for up to 30 input zones or addressable points.
• N-ANN-RLY: Relay module. Mounts inside the cabinet. Provides ten Form C relays.
• N-ANN-S/PG: Serial/parallel printer gateway. Provides a connection for a serial or parallel printer.
• N-ANN-I/O: Driver module. Provides connections to a user-supplied graphic annunciator.

Accessories

• DP-51050: Optional dress panel. Restricts access to the system wiring while allowing access to the membrane switch panel. Available in red.
• DP-51050B: Same as DP-51050 except in black.
• BB-26: Battery backbox, holds up to two 25 AH batteries and CHG-75.
• NFS-LBB: Battery backbox, holds up to two 55 AH batteries. Available in black.
• NFS-LBBR: Same as NFS-LBB except in red.
• TR-CE-B: Optional black trim-ring for semi-flush mounted cabinets.
• TR-CE: Same as TR-CE-B except in red.
• PRN-6: UL listed printer.

System Specifications

System Capacity

• Annunciators: 8

Electrical Specifications

• SFP-5UD(R) (FLPS-3 Power Supply): 120 VAC, 60 Hz, 1.0 A
• SFP-10UD(R) (FLPS-7 Power Supply): 120 VAC, 60 Hz, 3.90 A
• SFP-5UDE (FLPS-3 Power Supply): 240 VAC, 50 Hz, 0.54 A.
• SFP-10UDE (FLPS-7 Power Supply): 240 VAC, 50 Hz, 2.20 A.
• Wire size: minimum 14 AWG (2.0 mm²) with 600 V insulation, supervised, nonpower-limited.

Cabinet Specifications

• Door: 19.26" (48.92 cm.) high x 16.82" (42.73 cm.) wide x 0.72" (1.82 cm.) deep.
• Backbox: 19.00" (48.26 cm.) high x 16.65" (42.29 cm.) wide x 5.25" (13.34 cm.) deep.
• Trim Ring (TR-CE): 22.00" (55.88 cm.) high x 19.65" (49.91 cm.) wide.

Shipping Specifications

• Dimensions: 20.00" (50.80 cm.) high x 22.5" (57.15 cm.) wide x 8.5" (21.59 cm.) deep.
• Weight: 27 lb (12.20 kg).

Temperature and Humidity Ranges

This system meets NFPA requirements for operation at 0–49°C (32–120°F) and at a relative humidity of 93% ± 2% RH (noncondensing) at 32°C ± 2°C (90°F ± 3°F). However, the useful life of the system's standby batteries and electronic components may be adversely affected by extreme temperature ranges and humidity. It is recommended that this system and its peripherals be installed in an environment with a normal room temperature of 15–27°C (60–80°F).

Agency Listings and Approvals

The listings and approvals below apply to the basic SFP-5UD and SFP-10UD control panels. In some cases, certain modules or applications may not be listed by certain approval agencies, or listing may be in process. Consult the factory for the latest listing status.

• UL Listed: File S635
• FM Approved
• CSFM: 7165-0028:246
• MEA: MEA: 333-07-E
• Note: For ULC-listed models, see dn-60437.

NFPA Standards

The SFP-5UD/SFP-10UD(E) complies with the following NFPA 72 Fire Alarm Systems requirements:

• LOCAL (Automatic, Manual, Waterflow and Sprinkler Supervisory).
• AUXILIARY (Automatic, Manual and Waterflow) (requires 4XTM).
• REMOTE STATION (Automatic, Manual and Waterflow) (Where a DACT is not accepted, the alarm, trouble and supervisory relays may be connected to UL 864 listed transmitters. For reverse polarity signaling of alarm and trouble, 4XTM is required.)
• PROPRIETARY (Automatic, Manual and Waterflow).
• CENTRAL STATION (Automatic, Manual and Waterflow, and Sprinkler Supervised).
• OT, PSDN (Other Technologies, Packet-switched Data Network).