Whirlpool

Dimensions

The water filtration system has the following approximate dimensions:

• Height: 16 inches
• Width (across head assembly): 10-5/8 inches
• Depth (front to back of head assembly): 7-1/2 inches
• Sump diameter: 5-1/4 inches
• Overall width including fittings: 12 inches
• Overall depth including outlet fitting: 14 inches
• Outlet fitting height from base: 3-3/4 inches

FIG. 1 illustrates these dimensions with views of the filter head assembly and sump.

Specifications & Performance Claims

This system has been tested according to NSF/ANSI Standard 42 for particulate class III reduction (5 micron to less than 15 micron). The concentration of the indicated substance in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42. Testing was performed using spiked tap water at a flow rate of 4 GPM (15.2 L/min.), pH of 7.5 ± 0.5, pressure of 60 PSIG, and temperature of 68 ± 5°F.

SPECIFICATIONS

IMPORTANT NOTICE: Read this performance data and compare the capabilities of this unit with your actual water treatment needs. It is recommended that, before purchasing a water treatment unit, you have your water supply tested to determine your actual water treatment needs. This filter system is designed to be used for the reduction of the performance claims listed below. Do not use where water is microbiologically unsafe or of unknown quality, without adequate disinfection before or after the system. While testing was performed under standard laboratory conditions, actual performance of the system may vary based on local water conditions. Some or all of the contaminants reduced by this unit may not be in your water supply. See elsewhere in this manual for further instructions on system installation, operating procedures, filter cartridge replacement, and warranty. The maintenance instructions must be followed for the product to perform as indicated below.

Filter cartridges should be replaced every six months. Replacement filter cartridges are available at your nearest Lowe's store, or by calling 1-866-986-3223. Pricing will vary. Current pricing on replacement filter cartridge WHARF90 is approximately $30.00 to $60.00 per filter element.

PERFORMANCE CLAIMS

^j Micron is equivalent to micrometer (µm).

^k Milligrams per liter, which is equivalent to parts per million (PPM).

^l Acceptance level for this substance is based on percent reduction, rather than maximum effluent concentration.

^m Particles per milliliter.

ⁿ Environmental Protection Agency maximum contaminant level as required under the Safe Drinking Water Act.

Inspect Shipment

The parts required to assemble and install the water filtration system are included with the unit. Thoroughly check the water filtration system for possible shipping damage and parts loss. Also inspect and note any damage to the shipping carton.

Remove and discard (or recycle) all packing materials. To avoid loss of small parts, keep the small parts in the parts bag until you are ready to use them.

Packing List:

• Mounting Bracket with Screws
• Installation Adaptors
• Clips
• Vent Tube

FIG. 2 illustrates the included packing list items.

Before You Start

Your safety and the safety of others are very important. We have provided many safety messages in this manual and on your appliance. Always read and obey all safety messages.

Safety Alert Symbol: This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING”.

DANGER: You can be killed or seriously injured if you don't immediately follow instructions.

WARNING: You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, how to reduce the chance of injury, and what can happen if the instructions are not followed.

Installation and Usage Guidelines:

• Read all instructions before installing and using your UltraEase™ Pivotal Whole Home Water Filtration System. Follow all steps exactly to correctly install. Reading this manual will also help you to get all the benefits from the filtration system.
• All plumbing must be completed in accordance with national, state and local plumbing codes. Local code information can be obtained at your local public works department. In Massachusetts, plumbing code 248 CMR 3.00 and 10.00 shall be adhered to. Consult with your licensed plumber.
• Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.
• The UltraEase™ Pivotal Whole Home Water Filtration System works on water pressures of 30 psi (minimum) to 100 psi (maximum). If your house water pressure is over the maximum, install a pressure reducing valve in the water supply pipe to the filtration system.
• To condition all water in the home, install the filtration system close to the water supply inlet, and before all other plumbing connections, except outside water pipes.
• Do not install the filtration system outside, or in extreme hot or cold temperatures. Temperature of the water supply to the filtration system must be between 40°F and 100°F. Do not install on hot water.
• Avoid installing in direct sunlight. Excessive sun heat may cause distortion or other damage to non-metallic parts.

Planning the Installation

INSTALLATION LOCATION

To filter all household water, install the UltraEase™ Pivotal Whole Home Water Filtration System on the household's main incoming water pipe. For a home with municipal water supply, install the filter between the home's incoming water supply and the water softener, if a water softener is being used (See Figure 3A). If the home has well water, reverse the order of the filter and the water softener (See Figure 3B).

FIG. 3A shows installation with City Water Supply, including a water softener and heater.

FIG. 3B shows installation with Well Water Supply, including a well pump, pressure tank, water softener, and heater.

In some cases, it may be necessary for plumbing to cross over to ensure the correct flow direction through the filter (See Figure 4).

WARNING: Electrical Shock Hazard

Prior to installation on metallic plumbing, securely install two grounding clamps and a #4 copper wire per installation instructions. Failure to follow these instructions can result in death or electrical shock.

FIG. 4 illustrates a potential plumbing crossover scenario.

Typical Installation Illustrations

FIG. 5 shows the filter head assembly, installation adaptors, and clips. It advises to mount the included bracket to a strong, stable surface and hang the filter head on it before connecting to plumbing. Ensure all 3 tabs of the clip go through matching holes and fully into the channel on the installation adaptor.

FIG. 6 shows the sump and advises to allow at least a few inches of space under the sump to grasp and pivot it outward when replacing the filter cartridge.

FIG. 7 illustrates connecting the filter to plumbing using copper pipes or flexible connectors (not included). It shows the inlet and outlet ports (1" NPT) and notes the flow direction arrows on the filter. Use several wraps of Teflon® tape (not included) to seal inlet and outlet threads when installing. Use caution to avoid cross-threading the 1" NPT adaptors.

FIG. 8 shows the vent port barbed fitting and how to connect the vent tube. Press the end of the vent tube firmly over the barbed fitting. Route the vent tube down to a floor drain, laundry tub, or other suitable drain point.

Important Note: Do not solder metal plumbing while attached to plastic installation adaptors, as soldering heat will damage the adaptors. Teflon® is a registered trademark of E.I. Du Pont de Nemours and Company.

For questions, call 1-866-986-3223 or visit whirlpoolwatersolutions.com.

Installation Instructions

PLUMBING CODES

All plumbing must be completed in accordance with national, state and local plumbing codes. Local code information can be obtained at your local public works department. In Massachusetts, plumbing code 248 CMR 3.00 and 10.00 shall be adhered to. A licensed plumber shall be used for this installation.

ALWAYS INSTALL THE FILTER UPRIGHT

To operate properly, the UltraEase™ Pivotal Whole Home Water Filtration System must be installed in a vertical orientation. The filtration system must also be installed with the water flow following the arrows on the filter's inlet and outlet. This corresponds to a left-to-right flow, when looking at the front of the filter head assembly (See Fig. 7). Leave a few inches of space under the filter sump to allow it to be grasped, pivoted up and removed when changing filter cartridges, as shown in the "Filter Cartridge Replacement" section.

MOUNTING BRACKET

A metal bracket is included with the UltraEase™ Pivotal Whole Home Water Filtration System to support the assembled filter and plumbing when necessary. The bracket should be installed before the filter is connected to the plumbing.

The bracket may be mounted to a wall or wall framing member with two screws (included), as shown in Figure 6. These screws, or other (not included) fasteners, if used, must be mounted into a stable surface, strong enough to support the weight of the filter, plumbed and full of water - about 15 pounds.

The back of the filter head housing clips onto the bracket. When mounted, the filter should be aligned with the inlet and outlet plumbing, and not cause rigid pipes to distort.

CONNECT THE VENT TUBE

Each time you replace a filter cartridge, the filter will be placed into the bypass position by pivoting it outward (shown in the "Filter Cartridge Replacement" section). Whenever this is done, water pressure inside the sump is relieved, and about 4 ounces of water will be expelled through the vent port. Always install the included vent tube on this barbed fitting to carry the water to a floor drain, laundry tub or other suitable drain point. See Figure 8.

NOTE: This vent tube works by gravity. Do not elevate it above the vent port. Route it downward to the drain point with no humps, dips or loops.

WARNING: Electrical Shock Hazard

Prior to installation on metallic plumbing, securely install two grounding clamps and a #4 copper wire per installation instructions. Failure to follow these instructions can result in death or electrical shock.

GROUNDING INFORMATION (for Installations on Metal Pipe)

The house main incoming water pipe is often used to ground electrical outlets in the home. Grounding protects you from electrical shock. Installing the water filtration system may break this ground. Before beginning installation, purchase and securely install two grounding clamps and a #4 copper wire across the location where the filter will be, tightly clamping it at both ends, as shown below.

FIG. 9 illustrates the grounding connection with ground wire (not included) and clamps (2 - not included).

Properly discard (or recycle) all packing materials.

Filter Cartridges

FILTER CARTRIDGE LIFE

It is recommended to replace the filter cartridge every six months of use. Several variables determine how long a cartridge will last, including:

1. How much water you use.
2. How much sediment, taste and/or odor, or other unwanted substance, is in the water.

You will know it is time to replace the cartridge when you first notice the return of the unwanted sediment, taste and/or odor in your water, or when the flow diminishes or stops.

Register for reminders to change filters at whirlpoolwatersolutions.com.

The Whirlpool® UltraEase™ Pivotal Whole Home Water Filtration System model WHAWH90 with replacement element WHARF90 conforms to NSF/ANSI 42 for the specific performance claims as verified and substantiated by test data.

FILTER CARTRIDGE REPLACEMENT

NOTE: It is not necessary to shut off the water supply when replacing the filter cartridge.

1. Grasp the lower part of the sump and pull it firmly and slowly toward you, pivoting upward until it stops in the bypass/filter change position (See Fig. 10). You may notice a hissing sound, as a small amount of water (approximately 4 ounces) is expelled into the vent tube to relieve pressure in the sump.
2. Pull the sump downward out of the head.

NOTE: To avoid unintended water flow from the filter head, do not pivot the filter head down to the service position without the sump and replacement filter cartridge in place, as shown in Figure 16.

3. It is recommended to take the sump assembly to a sink or level waterproof surface before opening it.
4. Unsnap the lid clamp by pulling its latches in opposite directions, as shown in Fig. 11. Do not pry or use tools, as this may damage the assembly.
5. Swing the clamp halves open and lift the lid assembly up off the filter cartridge and sump.

NOTE: Do not remove the pin holding the clamp halves to the lid.

6. Remove the used filter cartridge from the sump. If you have difficulty removing the cartridge from the sump, insert a screwdriver into the slot shown in Figure 12 and pry up. Dispose of used cartridge properly.

NOTE: Check the sump to be sure it is dry and free of debris.

7. Take the new filter cartridge out of its packaging and remove the protective caps from the ports (See Fig. 13).
8. Filter cartridges can only be installed in one orientation and are “keyed” to assure proper fit. Insert the new filter cartridge into the sump, and turn it until the triangular points on its top edge align with, and drop into, the corresponding detents in the sump (see Fig. 13).
9. Slide the lid assembly down over the replacement cartridge's ports until it sits flat on top of the sump, then lock the clamp onto the sump by pinching together the latches, as shown in Fig. 15, until they snap. The clamp will not snap unless the cartridge and sump are properly seated and aligned.
10. Insert the sump assembly into the head by guiding the filter ports into the corresponding receptacles in the head and pushing the sump upward until it stops (See Fig. 16).
11. Pivot the sump all the way down to the service position.
12. Some types of filter cartridges contain activated carbon, a black powder. Open a faucet downstream from the filter to purge air and fine carbon particles from the cartridge. Flush for at least 5 minutes.

FIG. 10 shows how to pivot the sump to the bypass position and pull it down.

FIG. 11 shows the top view of the lid and how to unsnap the lid clamp.

FIG. 12 shows how to pry out a stuck filter cartridge.

FIG. 13 shows how to align the filter cartridge in the sump using triangular points and remove protective caps.

FIG. 14 illustrates the sump, filter cartridge, and lid assembly components.

FIG. 15 shows how to pinch the lid clamp latches to secure the assembly.

FIG. 16 shows inserting the sump assembly into the filter head and pivoting it down.

For questions, call 1-866-986-3223 or visit whirlpoolwatersolutions.com.

Troubleshooting the System

WARRANTY

TWO YEAR LIMITED WARRANTY ON UltraEase™ PIVOTAL WHOLE HOME WATER FILTRATION SYSTEM (except filter cartridges)

Warrantor: Ecodyne Water Systems, 1890 Woodlane Drive, Woodbury, MN 55125

Warrantor guarantees, to the original owner, that the UltraEase™ Pivotal Whole Home Water Filtration System, when installed and maintained in accordance with the instructions, will be free from defects in materials and workmanship for a period of two (2) years from the date of purchase. If, within the first two years, a part proves, after inspection, to be defective, Warrantor will, at its sole option, either replace or repair the part without charge except normal shipping and installation charges. Labor to maintain the equipment is not part of the warranty. Filters, which are expendable, are not covered by the warranty.

TO OBTAIN WARRANTY PARTS, SIMPLY CALL 1-866-986-3223, Monday - Friday, 8 am - 7 pm EST, for assistance. This warranty applies only while this product is in use in the United States or Canada.

General Provisions

The above warranties are effective provided the UltraEase™ Pivotal Whole Home Water Filtration System is operated at water pressures not exceeding 100 psi, and at water temperatures not exceeding 100°F; provided further that the UltraEase™ Pivotal Whole Home Water Filtration System is not subject to abuse, misuse, alteration, neglect, freezing, accident or negligence; and provided further that the UltraEase™ Pivotal Whole Home Water Filtration System is not damaged as the result of any unusual force of nature such as, but not limited to, flood, hurricane, tornado or earthquake.

Warrantor is excused if failure to perform its warranty obligations is the result of strikes, government regulation, materials shortages, or other circumstances beyond its control.

*THERE ARE NO WARRANTIES ON THE UltraEase™ PIVOTAL WHOLE HOME WATER FILTRATION SYSTEM BEYOND THOSE SPECIFICALLY DESCRIBED ABOVE. ALL IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE, ARE DISCLAIMED TO THE EXTENT THEY MIGHT EXTEND BEYOND THE ABOVE PERIODS. THE SOLE OBLIGATION OF WARRANTOR UNDER THESE WARRANTIES IS TO REPLACE OR REPAIR THE COMPONENT OR PART WHICH PROVES TO BE DEFECTIVE WITHIN THE SPECIFIED TIME PERIOD, AND WARRANTOR IS NOT LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES. NO WARRANTOR DEALER, AGENT, REPRESENTATIVE, OR OTHER PERSON IS AUTHORIZED TO EXTEND OR EXPAND THE WARRANTIES EXPRESSLY DESCRIBED ABOVE.

Some states do not allow limitations on how long an implied warranty lasts or exclusions or limitations of incidental or consequential damage, so the limitations and exclusions in this warranty may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. This warranty applies to consumer-owned installations only.

©/™ 2016 Whirlpool. All rights reserved. Manufactured under license by Ecodyne Water Systems, Woodbury, Minnesota.

Parts List

FIG. 11 shows the parts list for the system.

* Please purchase replacement cartridges from the retailer where you bought your water filtration system.

To order repair parts, call toll free 1-866-986-3223, Monday - Friday, 8 am - 7 pm EST.

Manufactured and warranted by Ecodyne Water Systems, 1890 Woodlane Drive, Woodbury, MN 55125