Whirlpool WHAFFS Water Filtration System

PRODUCT REGISTRATION AND WARRANTY

Register your product online to validate and extend your warranty period. Visit the warranty page for more information.

www.whirlpoolwatersolutions.com

If you have any questions or concerns when installing, operating, or maintaining your water filtration system, call our toll-free number:

1-866-986-3223

or visit whirlpoolwatersolutions.com

When calling, please be prepared to provide the product model number and date code, which are located inside the top cover.

System tested and certified by NSF International according to NSF/ANSI Standards 42 and 53. Consult performance data on page 10 for more details.

Manufactured and warranted by Water Channel Partners, 1890 Woodlane Drive, Woodbury, MN 55125, USA.

Document Revision: 201-8404384 (Rev. 04 5/27/20)

TABLE OF CONTENTS

• Before You Begin
• Specifications and Dimensions
• Parts and Tools
• Typical Under-Sink Installation
• Installation Instructions
• Step A - Install Water Supply Fittings
• Step B - Make Tube Connections
• Step C - Turn on Water, Check for Leaks, and Flush Carbon Fines
• Filter Cartridges
• Filter Cartridge Lifespan
• Filter Cartridge Replacement
• System Troubleshooting
• Detailed View and Parts List
• Warranty

Before You Begin

• Before installing and using the kitchen and bath water filtration system, carefully read all steps and guidelines. Follow all steps exactly to achieve correct installation. Reading this manual will also help you obtain all the benefits of the filtration system.
• If the water is microbiologically impure or its quality is unknown, do not use the system without adequate disinfection before or after the unit. This system has been certified for cyst reduction and can be used with disinfected water that may contain filterable cysts.
• All plumbing installation must be done in compliance with local codes and requirements. In the State of Massachusetts, plumbing codes 248 CMR 3.00 and 10.00 must be followed. Consult a licensed plumber.
• The kitchen and bath water filtration system operates with water pressures from 30 PSI (minimum) to 100 PSI (maximum), or 207 to 689 kPa. If your home's water pressure exceeds the maximum, install a pressure-reducing valve on the water supply line to the filtration system.
• Do not install the filtration system outdoors or under extremely hot or cold temperatures. The water supply temperature to the filtration system should be between 40 and 100 °F (4 and 38 °C). Do not install it on hot water pipes.

Specifications and Dimensions

Figure 1 shows the physical dimensions. The main unit is approximately 14-1/2 inches tall and 3-1/2 inches in diameter. The inlet and outlet connections are at the top, designed for 3/8 inch tubing.

Parts and Tools

Included:

• Filter head/bracket
• Top cover
• Filter cartridge
• Tubing
• Bag with installation parts and mounting screws

Not Included:

• Flathead and Phillips screwdrivers
• Pliers and extension wrench
• Tube cutters
• Electric drill
• Thread seal tape

Typical Under-Sink Installation

Locate the water filter assembly on the cold water supply line, under the kitchen or bathroom sink, to filter cold water. Refer to the following diagram.

Figure 2 illustrates a typical under-sink setup. It shows the filtered water faucet, the sink (FREGADERO), the cold water supply line (tubería de suministro de agua fría) with a shut-off valve (válvula de paso), the filter's inlet (ENTRADA) and outlet (SALIDA), and the connection to the faucet. The inlet connection has a yellow collar, and the outlet has a blue collar. The diagram notes that a minimum clearance of 1-1/2 inches is required below the system to remove the filter cartridge for replacement.

Installation Instructions

Step A - Install Water Supply Fittings

When planning the installation, consult and comply with local plumbing codes, then install the fittings to connect the kitchen and bath filter to the sink's cold water supply line. Included fittings (9/16-24 thread) and 3/8 inch OD tubing provide connections to and from the kitchen and bath filter inlet and outlet. Figure 3 illustrates a typical connection with the included water supply fittings.

1. Close the sink's shut-off valve(s) or another shut-off valve upstream from where you will install the filter, and open the faucets to relieve pressure in the sink's cold water supply line.
2. Identify the tubing connecting the cold water shut-off valve to the sink faucet. This tubing is usually a flexible hose. Disconnect the nut connecting this tubing to the cold water shut-off valve. Use a bucket to collect any water draining from this tubing.
3. Find a piece of the supplied 3/8 inch tubing, along with the included compression nut, ferrule, and tube insert. (See Figure 3). Assemble the parts onto the tubing as shown in Figure 3, and screw the compression nut onto the cold water shut-off valve. Tighten it to create a leak-proof connection.
4. Identify the water supply adapter (included) and install it onto the supply tubing nut you disconnected in Step 2. Refer to Figure 3.
5. Push the stem of the water supply adapter into one end of the supplied union connector. (See Figure 3). When tightening the stem, ensure it is fully seated.

Figure 3 shows the connection details: 3/8 inch tubing to the filter inlet (ENTRADA), compression nut, ferrule, insert, thread seal tape (use on threads), sink (FREGADERO), filtered water faucet (grifo de agua filtrada), flexible connection to faucet, inlet (ENTRADA) with yellow collar on push-to-connect fitting, outlet (SALIDA) with blue collar on push-to-connect fitting, cold water shut-off valve (válvula de paso de agua fría), water supply adapter (adaptador para suministro de agua), union connector (conector de unión), and 3/8 inch tubing from the filter outlet (SALIDA). The cold water shut-off valve is shown connected to the filter system assembly.

Step B - Make Tube Connections

1. Find the unused 3/8 inch tubing. Lay it between the union connector and the filter system outlet. (See Figures 2 and 3). Measure with some slack and cut it. Cut the tubing ends at a right angle.
2. Insert the tubing fully into the union connector and the filter system outlet. Pull on the tubing to ensure it is securely attached to the fittings.
3. Repeat steps 1 and 2 to connect the tubing installed on the cold water shut-off valve to the filter system inlet.

Tubing Connection (All Push-to-Connect Fittings): The system includes push-to-connect fittings for quick tubing connections. When working with the fittings, follow these guidelines:

Connect the Tubing:

1. Use a tube cutter to cut the tubing end at a right angle.
2. Inspect the tube end (approximately 1 inch or 25 mm) to ensure it is round and smooth, without nicks, scratches, or any uneven sections. If necessary, recut the tube.
3. Slide the tubing through the collar and insert it fully into the fitting. Full engagement is 3/4 inch (1.9 cm) of the tube portion inside the fitting.

Figure 4 illustrates correct and incorrect tubing connections. A correct connection shows a round, smooth tube end inserted 3/4 inch (1.9 cm) into the fitting. An incorrect connection shows partial insertion.

To Disconnect Tubing:

1. Push the collar inward and hold it with a finger while pulling the tubing out.

Figure 5 shows the disconnection process: push the collar (apretar para retirar el tubo) inward while pulling the tube.

Step C - Turn on Water, Check for Leaks, and Flush Carbon Fines

1. Open the supply valve(s) that you closed at the start of this installation.
2. Open the filtered water faucet to purge air from the system. When the water runs smoothly, without bubbles or intermittent spurts, close the faucet and check the installation for leaks.
3. Open the filtered water faucet and let the water run for 20 minutes to flush out carbon fines.

Filter Cartridges

Filter Cartridge Lifespan

Filter Cartridges: A filter cartridge contains activated carbon. When installing new cartridges, open the filtered water faucet and let the unit flush out carbon fines. Let the water run for 20 minutes. It is recommended to replace the filter cartridge every 6 months of use. Various variables will determine a cartridge's lifespan, including:

1. How much water is used, and
2. How much sediment, odor, or taste, or other undesirable substances are present in the water.

Use the following information as a guide. However, regardless of the type of cartridges you use, you will know it is time to replace them when you first notice sediment, taste, or odor in the water, or when the flow decreases or stops.

The Whirlpool® kitchen and bath water filtration system, model WHAFFS, with WHAFFF replacement element, meets NSF/ANSI Standards 42 and 53 for specific performance claims, which have been verified and substantiated by test data. The rated capacity of this system is 2000 gallons (7570 liters) at a nominal service flow rate of 1.85 gallons per minute (7.0 liters per minute).

Sign up at whirlpoolwatersolutions.com to receive filter change reminders.

Filter Cartridge Replacement

NOTE: It is not necessary to close the water shut-off valve when replacing the filter cartridge.

1. Turn the filter cartridge counter-clockwise to remove it from the filter head.
2. Dispose of the used cartridge properly.
3. Install the new cartridge. Turn the cartridge clockwise to attach it to the filter head.

Filter Cartridges: Filter cartridges contain a black powder that is activated carbon. When installing new cartridges, open the filtered water faucet and let the unit flush out carbon fines. Let the water run for 20 minutes.

Figure 6 shows the filter cartridge replacement. It depicts turning the filter cartridge to the left (counter-clockwise) to remove it from the filter head, and turning it to the right (clockwise) to attach it to the head.

System Troubleshooting

Parts List

Figure shows the filter assembly with numbered parts.

* Purchase replacement cartridges from the store where you bought the water filtration system.

Note: Not shown.

To order replacement parts, call toll-free at 1-866-986-3223.

Manufactured and warranted by Water Channel Partners, 1890 Woodlane Drive, Woodbury, MN 55125.

Warranty

EXTEND YOUR WARRANTY: Register your Whirlpool® replacement filter purchases. You can convert the one-year factory warranty of your water filtration system into a lifetime warranty by registering your Whirlpool® replacement filter cartridge purchases. See details in the "Lifetime Warranty" section below.

WARRANTY

KITCHEN AND BATH WATER FILTRATION SYSTEM - MODEL WHAFFS (excluding filter cartridges)

Warrantor: Water Channel Partners, 1890 Woodlane Drive, Woodbury, MN 55125

One-Year Warranty:

The warrantor guarantees to the original owner that the kitchen and bath water filtration system (WHAFFS), when installed and maintained in accordance with the instructions, shall be free from defects in material and workmanship for a period of one (1) year from the date of purchase.

Lifetime Warranty:

The warrantor guarantees only to the original owner that the kitchen and bath water filtration system (WHAFFS) shall be free from defects in material or workmanship for the owner's lifetime, provided that:

• The system is installed and maintained in accordance with the instructions in the same dwelling where it was originally installed.
• The owner replaces the filter every six (6) months and registers the purchase of the Whirlpool WHAFFF filter cartridge on the whirlpoolwatersolutions.com website. The purchase of no more than two (2) WHAFFF filter cartridges in a 12-month period may apply towards meeting this warranty.

Failure to meet the above requirements from the date of purchase will void the lifetime warranty.

If, within the first year, an inspection proves a part to have failed, the warrantor, at its sole discretion, will replace or repair such component at no charge, excluding shipping and installation costs. Labor for maintaining the equipment is not covered by the warranty. Filters are consumables and are not covered by warranty. TO OBTAIN WARRANTY PARTS, SIMPLY CALL 1-866-986-3223 for assistance. This warranty will apply only while the product is used in the United States or Canada.

General Provisions:

The preceding warranties will be valid provided that the kitchen and bath water filtration system operates at water pressures not exceeding 100 PSI (689 kPa), and water temperatures not exceeding 100 °F (38 °C), and provided that such system is not subjected to misuse, abuse, modification, neglect, freezing, accident, or negligence; and provided that such system is not damaged by any unusual force of nature, such as, but not limited to, flood, hurricane, tornado, or earthquake.

The warrantor is excused if failure to perform its warranty obligations is due to strikes, governmental regulations, shortage of materials, or other circumstances beyond its control.

* EXCEPT FOR THE WARRANTIES SPECIFICALLY DESCRIBED ABOVE, NO OTHER WARRANTY SHALL APPLY TO THE KITCHEN AND BATH WATER FILTRATION SYSTEM. ANY IMPLIED WARRANTY, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS EXCLUDED TO THE EXTENT THAT IT MAY EXTEND BEYOND THE PERIODS SPECIFIED ABOVE. THE SOLE OBLIGATION OF THE WARRANTOR UNDER THESE WARRANTIES IS TO REPLACE OR REPAIR THE COMPONENT OR PART WHICH IS PROVEN DEFECTIVE WITHIN THE SPECIFIED PERIOD. FURTHERMORE, THE WARRANTOR SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES. NO DISTRIBUTOR, AGENT, REPRESENTATIVE, OR ANY OTHER PERSON IS AUTHORIZED TO EXTEND OR ALTER THE WARRANTIES EXPRESSLY DESCRIBED ABOVE.

In certain jurisdictions, limitations on the duration of an implied warranty or exclusions or limitations of incidental or consequential damages are not permitted, so the limitations and exclusions of this warranty may not apply to you. This warranty gives you specific legal rights, and you may have other rights, which vary from jurisdiction to jurisdiction. This warranty applies only to installations owned by consumers.

©/TM ©2017 Whirlpool. All rights reserved. Manufactured under license by Water Channel Partners, Woodbury, Minnesota. Limited warranty provided by the manufacturer.