iBoard® by APS Installation Guide
Model: IB-231C&H
Before You Begin
Read these instructions carefully before starting installation. Remove all contents from the box and verify all parts are present. Assistance is recommended.
Mounting Type: Rocker Panel Mount
Drilling Required: No Drilling Required
Fastener Torque Specifications
| Fastener Size | Tightening Torque (ft-lbs) | Required |
|---|---|---|
| 6mm | 6-7 | X |
| 8mm | 16-18 | ✔️ |
| 10mm | 31-32 | X |
| 12mm | 56-58 | X |
| 14mm | 92-94 | X |
Part List
Step Bar Components:
Driver Side Step Bar
Passenger Side Step Bar
Mounting Brackets:
- Driver Front Mounting Bracket (DFM)
- Driver Center Mounting Bracket (DCM)
- Driver Rear Mounting Bracket (DRM)
- Passenger Front Mounting Bracket (PFM)
- Passenger Center Mounting Bracket (PCM)
- Passenger Rear Mounting Bracket (PRM)
Directional Indicator: The diagram indicates 'Front' [arrow pointing forward].
Hardware Packages
Hardware Package A (For Bracket Installation)
| Item | QTY | Description |
|---|---|---|
| 1# | 12 | M8X1.25-30mm Hex Bolts |
| 2# | 12 | M8 Large Flat Washers |
| 3# | 12 | M8 Lock Washers |
Visual description: Package A includes hex bolts, flat washers, and lock washers.
Hardware Package B (For Stainless Steel Step Bar Installation)
| Item | QTY | Description |
|---|---|---|
| 1# | 12 | M8X1.25-35mm Carriage Bolts |
| 2# | 12 | M8 Large Flat Washers |
| 3# | 12 | M8 Nylon Lock Nuts |
| 4# | 6 | Sliders (Packed with Step Bars) |
Visual description: Package B includes carriage bolts, flat washers, lock nuts, and sliders.
Installation Steps
Step 1: Driver Side Front Bracket
Start installation from the driver side front of the vehicle. Locate the two factory threaded holes in the side panel by the front flare. Partially attach the Driver Front Mounting Bracket (DFM) using two M8X1.25-30mm Hex Bolts, two M8 Lock Washers, and two M8 Large Flat Washers. Do not fully tighten hardware at this time.
Visual description: Diagram shows the Driver Side Front Mounting Bracket being attached with hardware. Labels indicate: (2) M8x1.25-30mm Hex Bolts, (2) M8 Large Flat Washers, (2) M8 Lock Washers. An arrow indicates 'Front' [arrow pointing forward].
Step 2: Driver Side Center Bracket
Move to the center of the vehicle. There are two sets of holes in the side panel between the installed mounting brackets. Partially install the Driver Center Mounting Bracket (DCM) using two M8X1.25-30mm Hex Bolts, two M8 Lock Washers, and two M8 Large Flat Washers. Do not fully tighten hardware at this time.
Visual description: Diagram shows the Driver Side Center Mounting Bracket being attached with hardware. Labels indicate: (2) M8x1.25-30mm Hex Bolts, (2) M8 Large Flat Washers, (2) M8 Lock Washers. An arrow indicates 'Front' [arrow pointing forward].
Step 3: Driver Side Rear Bracket
Move to the rear of the vehicle. Repeat Step 1 for the Driver Rear Mounting Bracket (DRM) installation. Do not fully tighten hardware at this time.
Visual description: Diagram shows the Driver Side Rear Mounting Bracket being attached with hardware. Labels indicate: (2) M8x1.25-20mm Hex Bolts, (2) M8 Large Flat Washers, (2) M8 Lock Washers. An arrow indicates 'Front' [arrow pointing forward].
Step 4: Step Bar Installation
Once all three driver side mounting brackets are installed, proceed to the Step Bar installation.
Slider Preparation:
- Select one Slider and two M8X1.25-35mm Carriage Bolts.
- Install the two Carriage Bolts into the Slider.
- Slide the Slider (with carriage bolts) onto the Step Bar.
- Repeat for the other two sliders.
Step Bar Attachment:
- Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to align with the brackets.
- Secure the Step Bar to the brackets using six M8 Large Flat Washers and six M8 Nylon Lock Nuts. Do not fully tighten hardware at this time.
Final Tightening: Level and adjust the Step Bar, then fully tighten all hardware. Repeat Steps 1-4 for the passenger side installation. The installation is now complete.
Visual description (Fig 4): Illustrates the process of attaching carriage bolts to a slider, and then attaching the slider to the step bar.
Visual description (Fig 5): Shows the step bar with sliders being mounted to a bracket using M8 Large Flat Washers and M8 Nylon Lock Nuts.
Attention
Perform periodic inspections to ensure all hardware is secure and tight. To protect your bars/boards, use only mild soap and non-abrasive products for cleaning.
