iBoard® Running Boards Installation Guide
Brand: iBoard by APS
Part Number: IB-030C&H
Note: Read instructions carefully before starting installation. Remove contents from box and verify all parts are present. Assistance is recommended.
*Rocker Panel Mount
*No Drilling Required
Fastener Torque Specifications
| Fastener Size | Tightening Torque (ft-lbs) | Required |
|---|---|---|
| 6mm | 6-7 | ❌ |
| 8mm | 16-18 | ✔️ |
| 10mm | 31-32 | ✔️ |
| 12mm | 56-58 | ❌ |
| 14mm | 92-94 | ❌ |
Part List
Driver Side Step Bar
Components include:
- Driver Front Mounting Bracket (DFM)
- Driver Rear Mounting Bracket (DRM)
Passenger Side Step Bar
Components include:
- Passenger Front Mounting Bracket (PFM)
- Passenger Rear Mounting Bracket (PRM)
(Diagrams show the general shape and mounting points of the step bars and their respective brackets.)
Hardware Package A (For Bracket Installation)
| Item | QTY | Description |
|---|---|---|
| 1# | 4 | M10X1.5-25 Bolt Plates |
| 2# | 4 | M10 Plastic Washers |
| 3# | 4 | M10 Flat Washers |
| 4# | 4 | M10X1.5 Nylon Lock Nuts |
| 5# | 8 | M8X1.25-25mm Hex Bolts |
| 6# | 16 | M8 Large Flat Washers |
| 7# | 8 | M8X1.25 Nylon Lock Nuts |
(Visuals show representations of each hardware item: bolt plates, plastic washers, flat washers, nylon lock nuts, hex bolts.)
Hardware Package B (For Stainless Steel Step Bar Installation)
| Item | QTY | Description |
|---|---|---|
| 1# | 8 | M8X1.25-35mm Carriage Bolts |
| 2# | 8 | M8 Large Flat Washers |
| 3# | 8 | M8 Nylon Lock Nuts |
| 4# | 4 | Sliders (Packed with Step Bars) |
(Visuals show representations of carriage bolts, large flat washers, nylon lock nuts, and sliders.)
Installation Steps
Step 1: Prepare Driver Side Front
Start installation from the driver side front of the vehicle. Insert one (1) M10 Bolt Plate into the rectangular hole located in the side panel. Thread one (1) M10 Plastic Washer onto the bolt plate to hold it in place.
(Diagram shows the M10 Bolt Plate being inserted into a vehicle side panel hole, with an arrow indicating 'Front' ⬆️. Scan for Installation Video ▶️)
Step 2: Attach Driver Front Mounting Bracket (DFM)
Select the Driver Front Mounting Bracket (DFM). Attach the DFM to the inserted M10 Bolt Plate using one (1) M10X1.5 Nylon Lock Nut and one (1) M10 Flat Washer. Do not fully tighten hardware at this time.
Note: The Driver Front Mounting Bracket (DFM) is shorter than the Rear one.
(Diagram shows the DFM bracket and its connection to the M10 Bolt Plate with the specified hardware. A 'W/ Notch' detail is shown on the DFM.)
Step 3: Secure DFM to Pinch Weld
Attach the Driver Front Mounting Bracket (DFM) to the pinch weld using two (2) M8x1.25-25mm Hex Bolts, two (2) M8x1.25 Nylon Lock Nuts, and four (4) M8 Large Flat Washers. Do not fully tighten hardware at this time.
Note: Ensure the vertical mounting plate on the bracket is on the outer side of the pinch weld.
(Diagrams show the DFM bracket being attached to the vehicle's pinch weld with the specified hardware. Hardware components are listed. Scan for Installation Video ▶️)
Step 4: Install Driver Side Rear Bracket
Move to the driver side rear of the vehicle. Repeat steps 1-3 to install the Driver Rear Mounting Bracket (DRM). Do not fully tighten hardware at this time.
Step 5: Install Step Bar
Once both driver side mounting brackets are installed, proceed to the Step Bar installation.
- Select one (1) Slider and two (2) M8X1.25-35mm Carriage Bolts.
- Install the two (2) M8X1.25-35mm Carriage Bolts into the (1) Slider.
- Slide the Slider (with carriage bolts) onto the Step Bar.
- Repeat to install the other slider onto the step bar.
- Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to align with the installed brackets.
- Secure the Step Bar to the installed Brackets using four (4) M8 Large Flat Washers and four (4) M8 Nylon Lock Nuts. Do not fully tighten hardware at this time.
Note: The Sliders are packed with the Step Bars.
Level and adjust the Step Bar, then fully tighten all hardware.
Repeat Steps 1-5 for the other side Step Bar installation. The installation is completed!
(Diagrams illustrate slider installation by inserting bolts into the slider and attaching it to the step bar. Another diagram shows the step bar with sliders being mounted to the vehicle bracket using washers and nuts. Scan for Installation Video ▶️)
Attention
Perform periodic inspections to ensure all hardware is secure and tight.
To protect your bars/boards, use mild soap and non-abrasive products for cleaning only.
Customer Support: info@iboardauto.com
Rev. 20230401
