Feit Electric 24 Inch Under Cabinet LED Light
Model: UCL24/5CCT
This document provides important safety instructions and a guide for installing and operating the Feit Electric 24-inch under cabinet LED light.
Important Safety Instructions and Installation Guide
Read all instructions before installation and save them for future reference.
Contact Feit Electric Customer Service:
Phone: 1-866-326-BULB (2852)
Website: FEIT.COM
Hours: 8 a.m. - 5 p.m., PST, Monday - Friday
Safety Information
- Always follow basic safety precautions when using electrical products, especially when children are present.
- CAUTION: Do not attempt to install while plugged in. This fixture is for indoor use only.
- Not for use with plastic cabinets.
- Do not install this fixture inside a totally enclosed cabinet.
- Do not mount over stoves.
- WARNING: To avoid risk of electrical shock, always ensure the product is unplugged from the electrical outlet before assembling, disassembling, relocating, servicing, or cleaning it.
- CAUTION: Do not install this product in a wet location.
- CAUTION: Do not install this product in an outdoor location.
- CAUTION: Do not use chemical solvents or harsh abrasives to clean the fixture.
Supplier's Declaration of Conformity
Responsible Party: Feit Electric Company
Address: 4901 Gregg Road, Pico Rivera, CA 90660, USA
Phone: 562-463-2852
Unique Identifier: UCL24/5CCT
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
If this equipment causes harmful interference to radio or television reception, try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.
CAN ICES-005(B).
Limited Warranty
This product is warranted to be free from defects in workmanship and materials for up to 5 years from the date of purchase. If the product fails within the warranty period, contact Feit Electric at info@feit.com, visit feit.com/contact-us, or call 1-866-326-BULB (2852) for instructions on replacement or refund. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY.
Liability for incidental or consequential damages is expressly excluded. Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.
Tools Required
Phillips head screwdriver
Pencil
Hardware Included
| Part | Description | Quantity |
|---|---|---|
| AA | 24in. LED Fixture | 1 |
| BB | 72in. Electrical Plug | 1 |
| CC | 18in. Linking Cable | 1 |
| DD | Mounting Screws | 2 |
| EE | Mounting Bracket | 2 |
| FF | Fixture Mounting Template | 1 |
Specifications
| Item No. | Description | Volts (V) | Wattage Per Fixture (W) | Input Current (mA) | Maximum Linkable Units at 120V | Maximum Linkable Units with In-Wall Dimmer |
|---|---|---|---|---|---|---|
| UCL24/5CCT | 24 Inch Under Cabinet LED Fixture | 120 | 17 | 220 | 45 | 5 |
Lighting Distribution
| Distance | Center Beam (Foot Candles) | Beam Diameter |
|---|---|---|
| 3 ft | 49 | 7.2 ft |
| 5 ft | 18 | 12 ft |
| 8 ft | 6.9 | 19 ft |
| 15 ft | 2.0 | 36 ft |
Beam Spread: 100 inches | CD @ CB: 440
Single LED Fixture Installation
-
Position the Fixture
Find the desired location for the LED light fixture. Use the provided mounting bracket template (FF) to mark the mounting points.
-
Install the Mounting Brackets
Screw the Mounting Brackets (EE) into the marked locations using the Mounting Screws (DD).
-
Install the LED Fixture
Align the LED Fixture (AA) with the Mounting Brackets (EE) and snap it into place. The fixture can be slid left or right for adjustment.
-
Connect the Electrical Plug
Plug the Electrical Plug (BB) into the LED Fixture (AA).
-
Connect to a Power Outlet
Connect the Electrical Plug (BB) to a wall power outlet.
Two or More LED Fixture Installation
-
Position the Fixtures
Find the desired locations for the LED light fixtures. Use the provided mounting bracket template (FF) to mark the mounting points for each fixture.
-
Install the Mounting Brackets
Screw the Mounting Brackets (EE) into the marked locations using the Mounting Screws (DD).
-
Install the LED Fixtures
Align the LED Fixtures (AA) with the Mounting Brackets (EE) and snap them into place. The fixtures can be slid left or right for adjustment.
-
Link the LED Fixtures
Connect the LED Fixtures (AA) together using the provided Linking Cable (CC).
-
Connect the Electrical Plug
Plug the Electrical Plug (BB) into the first LED Fixture (AA) in the linked series.
IMPORTANT: Do not plug the electrical plug into a wall power source until after connecting it to the LED Fixture (AA).
-
Connect to a Power Outlet
Connect the Electrical Plug (BB) to a wall power outlet.
Operating Instructions
ON/OFF and Dimming
Use the ON/OFF and Dim Button to turn the fixture on/off and adjust dimming levels. Cycle through dimming levels (High, Medium, Low, Dim, Off) by pressing the Dim Button. The selected setting will be retained when the fixture is turned on again.
Changing the Color Temperature Setting
Use the CCT Button to cycle through color temperature settings: 2700K, 3000K, 3500K, 4000K, 5000K. The selected setting will be retained when the fixture is turned on again.
Controlling Multiple Units
This LED fixture can operate and control multiple units, even if they are not physically linked.
- To group fixtures: Hold the CCT button for 3 seconds on all fixtures you wish to control as a group.
- To ungroup a fixture: Hold the CCT button on the fixture you want to control individually for 3 seconds.
