Feit Electric UCL12FP/5CCTCA Flat Panel Under Cabinet Light

Safety Information

IMPORTANT SAFEGUARDS:

ALWAYS FOLLOW BASIC SAFETY PRECAUTIONS WHEN USING ELECTRICAL PRODUCTS, ESPECIALLY WHEN CHILDREN ARE PRESENT.

Save These Instructions

CAUTION: Do not attempt to install while plugged in. This fixture is for indoor use only. Not for use with plastic cabinets. Do not install this fixture inside a totally enclosed cabinet. Do not mount over stoves.

WARNING: To avoid risk of electrical shock, always make sure the product is unplugged from the electrical outlet before assembling, disassembling, relocating, servicing or cleaning it.

CAUTION: Do not install this product in a wet location.

CAUTION: Do not install this product in an outdoor location.

CAUTION: Do not use chemical solvents or harsh abrasives to clean the fixture.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. Feit Electric Company, 4901 Gregg Road, Pico Rivera, CA 90660. www.feit.com, 1-800-543-3348.

Limited Warranty

This product is warranted to be free from defects in workmanship and materials for up to 1 year from date of purchase. If the product fails within the warranty period, please contact Feit Electric at info@feit.com, visit feit.com/contact-us or call 1-866 326-BULB (2852) for instructions on replacement or refund. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.

Pre-Assembly

TOOLS REQUIRED

• PHILLIPS SCREW DRIVER
• FLAT HEAD SCREW DRIVER
• PENCIL
• PLIAR
• WRENCH
• 18 AWG WIRE STRIPPER

HARDWARE INCLUDED

NOTE: Hardware not shown to actual size.

• AA: 12in. LED Flat Panel Fixture (Quantity: 1)
• BB: 18in. Connector Cable (Quantity: 1)
• CC: Mounting Screws (Quantity: 2)
• DD: Fixture Mounting Template (Quantity: 1)
• EE: Hardwire Bracket (Quantity: 1)
• FF: Hardwire Bracket Screw (Quantity: 1)
• GG: Wire Nut (Quantity: 3)
• HH: Clamp Connector (Quantity: 1)

Specifications

Single LED Fixture Hardwire Installation

1. Turn Off the Power

   Turn the power OFF from the breaker panel before starting installation.

   [Diagram Description: Breaker panel with switches indicating power status.]

2. Position the Fixture

   Find the desired place for the LED light fixture and mark clearly using the provided mounting bracket template (DD).

   [Diagram Description: Underside of the LED fixture and the mounting template (DD) showing placement.]

3. Installing the Mounting Screws

   Screw in the Mounting Screws (CC) on the marked locations, leaving a gap of 0.08-0.10 inches between the screw head and the installation surface.

   [Diagram Description: Marked locations on a surface with screws (CC) partially installed.]

4. Removing the Hardwire Bracket

   Remove the screw on the hardwire bracket, then slide and lift the bracket off of the fixture.

   [Diagram Description: The hardwire bracket (EE) being detached from the fixture.]

5. Removing the Knock-out

   Carefully remove the knock-out with a flathead screwdriver.

   [Diagram Description: A knock-out hole on a metal plate being removed with a flathead screwdriver.]

6. Installing the Clamp Connector to the Knockout Hole

   Install the Clamp Connector (HH) to the knock-out hole by inserting it through the hole and securing it with the nut. The Clamp Connector (HH) should be on the outer side of the bracket.

   [Diagram Description: The clamp connector (HH) and its securing nut being installed in the knock-out hole.]

7. Cutting and Stripping Wires

   Take out the black, white, and green 18AWG wires in the fixture. Cut and strip the wires to the correct length.

   [Diagram Description: Electrical wires (black, white, green) being cut and stripped.]

8. Wire Power Supply to the Fixture

   Feed the supply wire through the Clamp Connector (HH) and knockout hole and make all connections using the wire nuts provided. Connect the 120V line (black) wire to the black wire. Connect the neutral (white) wire to the white wire. Connect the ground (green) wire to the green wire.

   [Diagram Description: Wiring connections inside the fixture, showing black, white, and green wires connected with wire nuts (GG) and secured by clamp connector (HH).]

9. Replace the Wiring Bracket

   After connecting the wires correctly, place the wires inside the fixture and reinsert the bracket, sliding it over and screwing it secure.

   [Diagram Description: The wiring bracket (EE) being reattached to the fixture.]

10. Secure Supply Wires with the Clamp Connector

    Secure the supply wire by firmly screwing the clamp connectors down on the wire.

    [Diagram Description: Close-up of the clamp connector (HH) securing the electrical wire.]

11. Installing LED Fixture

    Align holes on the back of the fixture to the heads of the Mounting Screws. Slide fixture towards the mounting slot. If the fixture is not snug, remove the fixture and readjust the screws.

    [Diagram Description: The LED fixture being attached to the installed mounting screws.]

12. Linking LED Fixtures

    Connect the LED Fixtures (AA) using the provided Connector Cable (BB). NOTE: To install 2 or more LED fixtures, repeat the single fixture installation instructions with two or more units.

    [Diagram Description: Two LED fixtures (AA) connected by a connector cable (BB).]

Alternative Plug-In Installation

1. Position the Fixtures

   Find the desired place for the LED light fixture and mark clearly using the provided mounting bracket template (DD).

   [Diagram Description: Underside of the LED fixture and the mounting template (DD) showing placement.]

2. Installing the Mounting Screws

   Screw in the Mounting Screws (CC) on the marked locations, leaving a gap of 0.08-0.10 inches between the screw head and the installation surface.

   [Diagram Description: Marked locations on a surface with screws (CC) partially installed.]

3. Installing LED Fixture

   Align holes on the back of the fixture to the heads of the Mounting Screws. Slide fixture towards the mounting slot. If the fixture is not snug, remove the fixture and readjust the screws.

   [Diagram Description: The LED fixture being attached to the installed mounting screws.]

4. Connecting the Power Supply

   Plug In Electrical Plug to the LED Fixture (AA). NOTE: The electrical plug can be connected to either side of the LED Fixture (AA).

   [Diagram Description: An electrical plug being connected to the LED fixture (AA).]

5. Connecting to a Power Outlet

   Connect the Electrical Plug to the power outlet on the wall.

   [Diagram Description: An electrical plug connected to a wall power outlet.]

Operating Instructions

[Diagram Description: Fixture control buttons labeled 'ON/OFF and DIM Button' and 'CCT Button'.]

Use the ON/OFF and Dim Button for ON/OFF Operation and to Change the Dimming Levels

To select the desired dimming level, cycle through the dimming levels (High, Medium, Low, Dim, Off) by pressing the Dim Button. This setting will be fixed each time the ON/OFF switch is turned ON.

Changing the Color Temperature Setting

To select the desired color temperature, cycle through 2700K - 3000K - 3500K - 4000K - 5000K by pressing the CCT Button. This setting will be fixed each time the ON/OFF switch is turned ON.

Multiple Unit Control

This LED Fixture has the feature to operate and control multiple units, even if they are not linked.

• To control multiple fixtures, Hold the CCT button for 3 seconds on all the fixtures to be controlled in a group.
• To remove the individual fixture from the group, Hold the CCT button on the fixture that you want to control individually for 3 seconds.