Allen + Roth Wand Operated Outdoor Roller Shade

Introduction

Thank you for purchasing this Allen + Roth product. These instructions are designed to help you enjoy your product quickly. For more information, visit Lowes.com, search the item number, and refer to the 'Guides & Documents' tab. For questions or issues, contact customer service at 866-439-9800 (8 a.m. - 8 p.m. EST, Monday-Sunday).

Limited Warranty / Garantía Limitada

What is covered: This limited manufacturer warranty covers original defects in materials or workmanship for one year from the date of purchase, provided the product was properly installed and utilized. This includes internal mechanisms, components, brackets, and fabric.

What is not covered: Normal wear and tear; damage from abuse, accidents, alterations, misuse, or failure to follow instructions; discoloration from prolonged direct sunlight; slight or natural color variations.

Warranty Service: Claims require the original sales receipt. Contact customer service at 866-439-9800 for assistance. This warranty is not transferable to subsequent owners.

Warranty Remedy: The manufacturer will, at its discretion, repair and/or replace any defective component during the warranty period.

Exclusions: The manufacturer disclaims all other warranties, express or implied, including warranties of merchantability, fitness for a particular purpose, and non-infringement.

Limitation of Liability: The manufacturer is not liable for incidental, consequential, indirect, statutory, special, or punitive damages. No action shall be brought for any claim more than one year after the cause of action accrues, except for replacement of a defective product within the warranty period.

Care and Maintenance / Cuidado y Mantenimiento

Your Outdoor Roller Shade is made from fine materials. To clean, rinse with water, scrub with mild soap or a non-abrasive cleaner, rinse again, and allow to dry completely. Do not store the shade while wet. In moist areas, roll the shade down frequently to air dry.

CAUTION: Use of solvents or abrasive cleaners may damage the fabric and will void your warranty. Do not use bleach or chlorine.

Preparation / Preparación

Before installation, verify all parts are present by comparing them with the package contents and hardware lists. Do not attempt to assemble if any parts are missing or damaged.

Estimated Installation Time: 20 minutes

Tools Required (Not Included):

• Screwdriver [ screwdriver ]
• Drill [ drill ]
• Measuring Tape [ tape measure ]
• Pencil [ pencil ]
• Level [ level ]
• Safety Glasses [ safety glasses ]

Installation Guide / Guía de Instalación

Package Contents / Contenido del Paquete

A visual representation of the package contents shows:

• A - Idle End Unit Bracket (Left)
• B - Wand Unit Bracket (Right)
• C - Roller Tube
• D - Bottom Rail
• E - Bungees and Receivers
• F - Wand Eyelet
• Shade
• Wand

Hardware Contents / Aditamentos

The hardware contents include:

• G - Wood Screws (x8)

Installation Overview / Descripción General de la Instalación

Your roller shade is ready for mounting to a vertical surface. For top mounting (e.g., ceiling), you will need to make a simple change to your Wand Unit Bracket and Idle End Unit Bracket before installation. For wall mounting, proceed to Step 2.

Step 1 & 2: Bracket Preparation and Placement

Remove the two screws from both brackets A & B. Turn the Wand Unit 90° so the wand eyelet hangs straight down. Turn the Idle End Unit 90° so the opening faces away from the window or surface, then reinsert the screws.

The bracket-to-bracket distance should be the shade width plus 2.75 inches (6.98 cm). Center this calculated width on your opening and mark each side. Ensure at least 2.25 inches (5.71 cm) clearance between the wall or ceiling to allow the shade to roll up completely. Place the outside edge of the brackets on each mark, then mark the screw holes.

Step 3: Install Brackets

Install brackets with screws at the center of the screw holes to ensure enough space for adjustment. The Wand Unit Bracket should be on the right side, and the Idle End Unit Bracket on the left side. Note: The included screws are for wood only. Consult a store associate for mounting recommendations for other materials.

Step 4: Attach Wand and Plugs

Insert the Wand Side Plug into the Wand Unit Bracket. Then, insert the Idle End Plug into the Idle End Unit Bracket and snap it securely into place. Attach the Wand to the Wand Eyelet.

Step 5a & 5b: Check Level and Adjust / Remove Shade

After installation, check that the shade is level. Ensure side-to-side movement does not exceed 1/16 inch. If it does, the brackets are too far apart.

To adjust: Loosen the screws on the idle side, slide the bracket inward, retighten screws, and reinstall the shade.

To remove the shade: Roll it up completely. Use a flathead screwdriver to gently press upward in the opening on the Idle End Unit Bracket while gently pulling forward on the left side of the roll to release the shade from the bracket. Once disengaged, slide the wand side of the roller shade out.

Step 6 & 7: Optional Bungee Tie Downs

Optional Bungee Tie Downs are provided to secure your shade in mild to moderate wind conditions. Install the Receivers approximately 5 inches (13 cm) below where the shade will stop to allow for proper tension of the Bungee cord.

Note: Roll up your shade when not in use or before strong winds to prevent damage.

Thread the Bungee through the End Cap hole on the shade and feed the ball end back through the loop to make a knot. Attach the Bungees to the Receivers to secure the shade.