Shelly Wave Pro 3
3-channel DIN-rail mounted Z-Wave® smart switch with potential-free contacts
User and Safety Guide
This document contains important technical and safety information regarding the Device, its safe use, and installation.
WARNING! Before starting installation, please read this manual and all other documents accompanying the device carefully and in their entirety. Failure to follow the installation procedures may lead to malfunction, danger to your health and life, violation of the law, or refusal of legal and/or commercial warranty (if any). Shelly Europe Ltd. is not responsible for any loss or damage in case of incorrect installation or incorrect operation of this device due to non-compliance with the user and safety instructions in this manual.
About the Device
The device is a DIN-rail mounted 3-channel smart switch with potential-free contacts. It controls the on/off function of three independent electrical devices with a load of up to 16 A per channel (48 A total). It is compatible with switches (by default) and buttons. It also supports load control on single-phase or three-phase systems.
WARNING! Risk of electric shock. Installation of the Device to the power supply must be carried out with caution by a qualified electrician.
WARNING! Risk of electric shock. Any changes to the connections must be made after ensuring that there is no voltage at the device terminals.
WARNING! Use the device only with electrical networks and appliances that comply with all applicable regulations. A short circuit in the electrical network or any appliance connected to the Device may damage it.
WARNING! Do not connect the device to appliances exceeding the specified maximum load!
WARNING! Leave at least 10 mm space around each Pro device if you expect currents higher than 5 A per channel.
WARNING! Connect the device only as shown in these instructions. Any other method may cause damage and/or injury.
WARNING! Do not install the Device in places where it can get wet.
WARNING! Do not use the device if it is damaged!
WARNING! Do not attempt to service or repair the Device yourself!
WARNING! Before starting the installation of the Device, check that the circuit breakers are switched off and there is no voltage at their terminals. This can be done with a mains voltage tester or a multimeter. Once you are sure there is no voltage, you can proceed with connecting the wires.
WARNING! Do not let children play with the switches/buttons connected to the Device. Keep Shelly Wave remote control devices (mobile phones, tablets, computers) away from children.
WARNING! Do not shorten the antenna.
RECOMMENDATION: Position the antenna as far as possible from metal objects, as they can cause signal interference.
RECOMMENDATION: Connect the device using solid single-wire cables with increased heat resistance of the insulation, not lower than PVC T105°C (221°F).
RECOMMENDATION: For inductive loads that cause voltage spikes during switching on/off, such as electric motors, fans, vacuum cleaners, and similar, an RC suppressor (0.1 μF / 100 Ω / 1/2 W / 600 V AC) should be connected in parallel to the load.
Device Terminals
- N: Neutral terminal
- L: Live terminal (110-240 V~)
- SW (SW1): Input terminal for switch/button (controlling O1)
- SW2: Input terminal for switch/button (controlling O2)
- SW3: Input terminal for switch/button (controlling O3)
- I1: Load input terminal for circuit 1
- I2: Load input terminal for circuit 2
- I3: Load input terminal for circuit 3
- O (01): Load output terminal for circuit 1
- O2: Load output terminal for circuit 2
- O3: Load output terminal for circuit 3
Wiring Diagram
Figure 1 / Three-phase wiring
- N: Neutral wire
- L1(A): Load circuit phase 1 live wire (110-240 V~)
- L2(B): Load circuit phase 2 live wire (110-240 V~)
- L3(C): Load circuit phase 3 live wire (110-240 V~)
Figure 2 / Single-phase wiring
- N: Neutral wire
- L: Load circuit 1 live wire (110-240 V~)
- L: Load circuit 2 live wire (110-240 V~)
- L: Load circuit 3 live wire (110-240 V~)
- Button: S: S button
For more installation instructions, visit: https://shelly.link/ShellyWavePro3_LR-KB
Technical Specifications
- Power supply: 110-240 V AC, 50/60 Hz
- Power consumption: < 0.3 W
- Max. switching voltage AC: 240 V
- Max. switching current AC: 16 A per channel, 48 A total
- Max. switching voltage DC: 30 V
- Max. switching current DC: 16 A per channel, 48 A total
- Overheating protection: Yes
- Power metering (W): No
- Wireless protocol: Z-Wave
- CPU: S800
- Z-Wave® Mesh frequency band: 868.4 MHz
- Z-Wave® Range: Up to 80 m indoors (262 ft.) or up to 1000 m outdoors (3281 ft.)
- Z-Wave® Long Range frequency band: 864 MHz
- Z-Wave® repeater: No (Long Range), Yes (Mesh)
- Dimensions (H x W x D): 96x53x59 ±0.5 mm / 3.78x2.01x2.32 ±0.02 inches
- Weight: 150 g / 5.29 oz.
- Mounting: DIN rail
- Terminal screw torque max: 0.4 Nm / 3.54 lbin
- Wire cross-section: 0.5 to 2.5 mm² / 20 to 14 AWG
- Stripped wire length: 6 to 7 mm / 0.24 to 0.28 inches
- Enclosure material: Plastic
- Color: Black
- Ambient operating temperature: -20°C to 40°C / -5°F to 105°F
- Humidity: 30% to 70% RH
- Max. altitude: 2000 m / 6562 ft.
IMPORTANT DISCLAIMER
Z-Wave® wireless communication may not always be 100% reliable. This device should not be used in situations where life and/or valuables depend solely on its functioning. If the device is not recognized by your gateway or is displayed incorrectly, you may need to manually change the device type and ensure your gateway supports Z-Wave Plus® multichannel devices and the Z-Wave® Long Range capability in case of long-range devices.
ORDER CODE: QUSW-0A3X16EU
DECLARATION OF CONFORMITY
Hereby, Shelly Europe Ltd. declares that the radio equipment type Shelly Wave Pro 3 is in compliance with Directive 2014/53/EC, 2014/35/EC, 2014/30/EC, 2011/65/EC. The full text of the EC declaration of conformity is available at the following internet address: https://shelly.link/ShellyWavePro3-DoC
For UP PSTI Act Statement of Compliance scan the QR code.
MANUFACTURER:
Shelly Europe Ltd.
Address: Cherni vrah Blvd. 103, 1407 Sofia, Bulgaria
Tel.: +359 2 988 7435
E-mail: zwave-shelly@shelly.cloud
Support: https://support.shelly.cloud/
Website: https://www.shelly.com
Changes to the contact details are published by the Manufacturer on the official website: https://www.shelly.com
V1
CE ? RoHS COMPLIANT ♺ ♻️
