Shelly Wave Pro 1PM - User and Safety Manual
Intelligent Z-Wave® Switch with DIN Rail Mounting and Power Metering
Introduction
This document contains important technical and safety information regarding the Device, its safe use, and installation.
WARNING! Please read this manual and any other accompanying documents carefully and in their entirety before starting the installation. Failure to follow installation procedures may result in malfunction, danger to your health and life, violation of law, or denial of warranty. Shelly Europe Ltd. is not responsible for any losses or damages in case of improper installation or incorrect operation of this device due to non-compliance with the user and safety instructions in this manual.
Terminology and Abbreviations
Gateway: A Z-Wave® gateway, also known as a Z-Wave® controller, Z-Wave® master controller, Z-Wave® primary controller, or Z-Wave® hub, is a device that serves as a central hub for a Z-Wave® smart home network. The term "gateway" is used in this document.
Button S: The service button on Z-Wave® devices used for functions like inclusion (adding), exclusion (removing), and resetting the device to its factory default settings. The term "Button S" is used in this document.
Device: In this document, the term "Device" refers to the Shelly Qubino device that is the subject of this manual.
About Shelly Qubino
Shelly Qubino is a line of microprocessor-controlled devices that allow remote control of electrical circuits via smartphone, tablet, computer, or home automation system. They operate on the Z-Wave® wireless communication protocol, requiring a gateway for device configuration. When the gateway is connected to the internet, Shelly Qubino devices can be controlled remotely from anywhere. Shelly Qubino devices can operate in any Z-Wave® network with other certified Z-Wave® devices from other manufacturers. All mains-powered nodes will act as repeaters, regardless of the vendor, to increase network reliability. The devices are designed to work with older generations of Z-Wave® devices and gateways.
Wave Pro Series
The Wave Pro series is a line of devices suitable for homes, offices, shops, manufacturing facilities, and other buildings. Pro devices are mounted on a DIN rail inside a breaker box and are exceptionally suitable for new building constructions. All Wave Pro devices can be controlled and monitored via the Z-Wave® network.
About the Device
The device is an intelligent DIN rail mountable switch with power metering. It controls the on/off function of a single electrical device with a load of up to 16 A. It is compatible with switches (default) and buttons.
Installation Instructions
The device can be mounted on a DIN connector inside the breaker box. Refer to the wiring diagram (Fig. 1) in this user manual for installation instructions.
WARNING! Electric shock hazard. Installation of the device to the electrical grid must be performed with caution by a qualified electrician.
WARNING! Use the device only with electrical grids and appliances that comply with all applicable regulations. A short circuit in the electrical grid or any appliance connected to the device may damage it.
WARNING! Do not connect the device to appliances exceeding the specified maximum load!
WARNING! Leave at least 10 mm clearance around each Pro device if you expect currents higher than 5 A per channel.
WARNING! Connect the device only as shown in these instructions. Any other method may cause damage and/or injury.
WARNING! Do not install the device in locations where it can get wet.
WARNING! Do not use the device if it is damaged!
WARNING! Do not attempt to service or repair the device yourself!
WARNING! Before starting the installation of the Device, check that the circuit breakers are off and there is no voltage on their terminals. This can be done with a voltage tester or multimeter. Once you are sure there is no voltage, you can proceed with wiring the conductors.
WARNING! Do not allow children to play with the switches/buttons connected to the device. Keep Shelly Qubino remote control devices (mobile phones, tablets, computers) away from children.
WARNING! Do not shorten the antenna.
Recommendation: Place the antenna as far as possible from metal elements, as they can cause signal interference.
Recommendation: Connect the device using solid single-core wires or stranded wires with ferrules. The wires must have insulation with increased heat resistance, not less than PVC T105°C (221°F).
Recommendation: For inductive loads that cause voltage spikes during switching, such as electric motors, fans, vacuum cleaners, and similar, an RC suppressor (0.1 μF / 100 Ω / 1/2 W / 600 V AC) should be connected in parallel to the load.
Wiring Diagram Description (Fig. 1)
- Device Terminals:
- N: Neutral terminal
- L: Live terminal (110-240 V AC)
- SW (SW1): Input terminal for switch/button (controlling O (01))
- SW2: Input terminal for switch/button
- I: Input terminal for the load circuit
- O (01): Output terminal (1) for the load circuit
- Conductors:
- N: Neutral conductor
- L: Live conductor (110-240 V AC)
- Button:
- S: Button S
Connect the load to the O terminal of the device and the neutral conductor as shown in Fig. 1. Connect the phase conductor to the I terminal of the device. Connect the neutral conductor to the N terminal of the device. Connect a switch or button to the SW1 (SW2) terminal of the device and the phase conductor.
For more detailed installation instructions, use cases, and comprehensive guidance on adding/removing the device to/from a Z-Wave network, resetting to factory settings, LED signaling, Z-Wave command classes, parameters, and more, refer to the extended user manual at: https://shelly.link/WavePro1PM-KB
Specifications
| Parameter | Value |
|---|---|
| Power supply | 110-240 V AC, 50/60 Hz |
| Power consumption | < 0.3 W |
| Max. switching current AC | 16 A |
| Max. switching voltage AC | 240 V |
| Max. switching voltage DC | None specified |
| Max. switching current DC | None specified |
| Overheating protection | Yes |
| Overload protection | Yes |
| Overvoltage protection | Yes |
| Range | Up to 40 m indoors (131 ft) (depending on local conditions) |
| Z-Wave® repeater | Yes |
| Processor | Z-Wave® S800 |
| Z-Wave® frequency bands | 868.4 MHz |
| Max. radio frequency power transmitted in frequency band(s) | < 25 mW |
| Dimensions (H x W x D) | 94x19x69 ±0.5 mm / 3.70x0.75x2.71 ±0.02 inches |
| Weight | 61 g / 2.15 oz. |
| Mounting | DIN rail |
| Max. torque of screw terminals | 0.4 Nm / 3.54 lbf.in |
| Wire cross-section | 0.5 to 2.5 mm² / 20 to 14 AWG (green connector) 0.5 to 1.5 mm² / 20 to 16 AWG (white connectors) |
| Stripped wire length | 6 to 7 mm / 0.24 to 0.28 inches (green connector) 5 to 6 mm / 0.20 to 0.24 inches (white connectors) |
| Enclosure material | Plastic |
| Color | Red |
| Ambient temperature | -20°C to 40°C / -5°F to 105°F |
| Humidity | 30% to 70% relative humidity |
| Maximum altitude | 2000 m / 6562 ft |
Operating Instructions
SW1: If the switch (SW1) is configured as a switch (default), any toggle of the switch will change the state of output O (01) to the opposite: on, off, on, etc. If the switch (SW1) is configured as a button in the device settings, each press of the button will change the state of output O (01) to the opposite: on, off, on, etc.
SW2: NO relay control, used for associations only.
Supported Load Types
- Resistive (incandescent lamps, heating devices)
- Inductive with RC suppressor (LED drivers, transformers, fans, refrigerators, air conditioners)
- Capacitive (capacitor banks, electronic equipment, motor start capacitors)
Important Disclaimer
Z-Wave® wireless communication may not always be 100% reliable. This device should not be used in situations where life and/or valuables depend solely on its functioning. If the device is not recognized by your gateway or is displayed incorrectly, you may need to manually change the device type and ensure your gateway supports Z-Wave Plus® multichannel devices.
Manufacturer
Manufacturer: Shelly Europe Ltd.
Address: Cherni Vrah Blvd 103, 1407 Sofia, Bulgaria
Tel: +359 2 988 7435
E-mail: zwave-shelly@shelly.cloud
Support: https://support.shelly.cloud/
Website: https://www.shelly.com
Changes to contact details are published by the Manufacturer on the official website: https://www.shelly.com
Declaration of Conformity
Hereby, Shelly Europe Ltd. declares that the radio equipment type Wave Pro 1PM is in compliance with Directive 2014/53/EC, 2014/35/EC, 2014/30/EC, 2011/65/EC. The full text of the EU declaration of conformity is available at the following internet address: https://shelly.link/WavePro1PM-DOC
Certifications: CE RoHS COMPLIANT
