[Tow-Trust Logo] Tow-Trust Towbars
Important: Please read General Notes overleaf before fitting
Issue 3
Vehicle Compatibility
This towbar (Model TST2SN) is compatible with the following vehicles:
- AUDI A1 (2010 onwards)
- AUDI A1 SPORTBACK (2012 onwards)
- SEAT IBIZA HATCH (2008 onwards)
- SEAT IBIZA ST (2010 onwards)
- VOLKSWAGEN POLO (2009 onwards)
- SKODA FABIA 2 HATCH (2007 onwards)
- SKODA FABIA 2 ESTATE (2008 onwards)
Parts List
| Item | Qty | Description | Item | Qty | Description |
|---|---|---|---|---|---|
| A | 1 | Crossbar | E | 1 | VASP8 L/H Socket Plate |
| B | 1 | ACS4 / 9204 Swan Neck | F | 8 | M10 x 40 Bolts, 2 Nuts & 8 S/P Washers |
| C | 2 | Side Arms | G | 2 | 15mm Spacer Plates |
| D | 2 | M10 Clamp Plates | H | 2 | M12 x 110 Grade 10.9 Bolts & Nyloc Nuts |
| J | 6 | 10 x 30 Flat Washers | |||
| K | 4 | 12 x 25 Flat Washers |
Installation Steps
- For SEAT IBIZA, SEAT IBIZA ST & SKODA FABIA HATCH & ESTATE: Remove the rear light clusters.
- Remove the rear bumper.
- Remove the rear crash beam (This is not refitted with the Towbar assembly).
- Locate Towbar mounting points on the outside face of each chassis member; these are usually covered in tape.
- Insert items C (Side Arms) into each chassis member. Choose the correct hole location for the vehicle. Line up with Towbar mounting points in chassis members, then loosely fix in place using item F (M10 Bolts) and item J (10x30 Flat Washers). Use item D (M10 Clamp Plates) on the forward most mounting point if needed.
- Using item F (M10 Bolts) and item J (10x30 Flat Washers), bolt item A (Crossbar) between items C (Side Arms).
- Using item H (M12 Bolts) with item K (12x25 Flat Washers) and item G (15mm Spacer Plates), bolt item B (Swan Neck) and item E (Socket Plate) to item A (Crossbar).
- Fully tighten all nuts and bolts, ensuring the Towbar is rigid, square, and secure.
- Cut the bumper to the correct sketch for your vehicle and refit.
Diagram Descriptions
Vehicle Key: This section illustrates how different vehicle models correspond to specific fitting points or orientations shown in the main assembly diagram. It maps:
- SEAT IBIZA
- FABIA EST (Skoda Fabia Estate)
- POLO (Volkswagen Polo)
- AUDI A1
- FABIA (Skoda Fabia Hatch)
- SEAT IBIZA ST
Main Towbar Assembly Diagram (TST2SN): This diagram shows the overall structure of the towbar. It depicts the main crossbar (A) as a horizontal beam. Side arms (C) extend downwards and forwards from the ends of the crossbar, connecting to the vehicle chassis. M10 clamp plates (D) are shown as potential mounting hardware. The swan neck tow ball assembly (B) and the electrical socket plate (E) are shown attached to the front of the crossbar. Various fasteners, including bolts (F, H), nuts, and washers (G, J, K), are indicated for assembly.
Vehicle-Specific Fitting Diagrams: These diagrams illustrate the mounting points and dimensions for attaching the towbar to different vehicle chassis. They show:
- VW POLO: A diagram indicating specific chassis mounting points with dimensions, including a 90mm measurement and a 160mm measurement. A "[Centre Line Indicator]" is shown.
- AUDI A1 / SKODA FABIA: A diagram showing chassis mounting points with a 90mm measurement and a 120mm measurement. A "[Centre Line Indicator]" is shown.
- SEAT IBIZA: A diagram indicating chassis mounting points with a 90mm measurement. A "[Centre Line Indicator]" is shown.
- SEAT IBIZA ST: A diagram indicating chassis mounting points with a 90mm measurement. A "[Centre Line Indicator]" is shown.
- FABIA EST: A diagram indicating chassis mounting points with a 90mm measurement. A "[Centre Line Indicator]" is shown.
The diagrams use labels like 'F', 'J', 'H', 'K', 'G', 'E', 'B', 'A', 'C', 'D' to reference the parts listed.
Important Notes
- Note 1: Recommended Torque Setting for M12 Grade 10.9 bolts is 139 Nm. (For other Torque Settings, please refer to notes overleaf, which are not included in this document excerpt).
- Note 2: Nose load limits and vehicle manufacturer's trailer/caravan weight limits must be observed.
