Statement
Thank you very much for using the R11 vehicle terminal (mobile user terminal) product. Please read this manual carefully before use. Please pay attention to all the cautions and warnings mentioned in the manual. Please keep this manual properly for reference.
This manual, as well as the description of the software, can be used or copied directly after receiving the license, only in accordance with such authority.
The content of this manual is to provide information for use, subject to change without notice, and should not be regarded as a commitment by SEEWORLD. SEEWORLD assumes any liability or any deviation of legal liability may appear in this book.
SEEWORLD Company reserves the right to make changes to specifications at any time without notice. SEEWORLD Corporation believes that this manual is accurate and reliable. However, SEEWORLD Corporation is not responsible for its use, or infringement of patents or the rights of other third parties caused by its use. Without a license, any patents or patent rights will belong to SEEWORLD.
Content
- Product Description
- Product Features
- Specifications
- Appearance
- Installation Instructions
- Setting Command Instructions
- Installation diagram
- Troubleshooting
1. Product Description
The R11 is a multifunctional GPS tracker with a wide range of applications. Adopts MTK6261 chip and supports GPS, COMPASS, GLONASS satellite systems. In addition to supporting satellite positioning, the equipment also supports single-base and multi-base station positioning. Rich extended functions, please refer to the following descriptions about extended functions. Integrating a self-developed hardware monitoring circuit enables the equipment to work reliably and stably for a long time, and can automatically recover when an abnormality occurs.
2. Product function
- GSM quad-band, built-in GSM/GPS antenna;
- Support all global navigation satellite systems GPS, COMPASS, GLONASS, Beidou that have been deployed and will be in operation
- Support global multi-base station and satellite positioning mode;
- Voltage input 9-90V;
- Built-in high-power surge protection circuit;
- Adopt high temperature resistant, safe and explosion-proof rechargeable lithium cobalt oxide battery;
- Built-in high-power surge protection circuit;
- Built-in hardware monitoring circuit, automatic recovery of abnormal state;
- Support remote oil circuit control;
- Support ACC detection and alarm;
- Built-in battery switching circuit, support power failure alarm;
- Built-in vibration sensor, support vibration alarm;
- Support remote upgrade;
- IP65 waterproof design;
3. Specification
| Items | Specifications | Remark |
|---|---|---|
| Working Voltage | DC9V-90V | |
| Working Current | 25ma @12V (Quiescent current 10mA) | Not charging |
| Dimension | L80mm *W28mm*H14mm | |
| Positioning mode | GPS+LBS+WIFI(Optional) | |
| Positioning error | <10 Meters | |
| communication network | GPRS | |
| GSM frequency | 850/900/1800/1900MHz | |
| Communication way | TCP | |
| Temperature range | -25°C~+75°C | |
| Storage temperature range | -40°C ~ +85°C | |
| Backup battery working time | 0.5h | |
| Warranty period | 1 Year |
4. Appearance
By checking the status indicator, you can understand the working condition of the device. The status of the indicator is described as follows:
| LED Color | LED Status | Description |
|---|---|---|
| Red | Fast flash | GSM starting |
| Slow flash | GPS receive signal is normal | |
| light | GPRS online | |
| Drak | No GSM signal/card/still sleep | |
| Blue | Fast flash | GPS signal searching |
| Light | GPS position | |
| Dark | GPS sleep/not working |
5. Installation instructions
5.1. Wiring
A diagram shows a wire harness with four colored wires: Yellow, Orange, Black, and Red, connecting to a connector.
| Line No. | Specification | Color | Instruction |
|---|---|---|---|
| 8 | MOTOR | Yellow | Fuel control wire |
| 9 | ACC | White | ACC |
| 10 | V- | Black | 12V/24V |
| 11 | ACC | Red | Connect to Power of 12V/24V |
Connection diagram of remote cut-off oil and electricity (optional function)
A diagram illustrates the wiring for remote cut-off of oil and electricity. It shows connections to the oil pump, a relay (12V), power supply (9-90V), and the car key bit (ACC, LOCK, START). The diagram specifies wire colors (Red, Black, Orange, Green, Yellow) and their connections, including the yellow wire connected to the 12V normal power positive pole and the device relay control wire.
Precautions for Relay Wiring
Pump relay wiring: the oil connectors at both ends are thin white wire (85) and thin yellow wire (86). The thin white wire (85) is connected to the vehicle's positive power supply (+12V). The thin yellow wire is connected to the device relay control wire. Cut off the positive connection wire of the pump; then connect in series to the relay normally closed contact (green thick line 87a), and the other end to the relay COM contact (green thick line 30).
6. Description of command Instructions
6.1. Oneline Setting Command List
| 1 | SERVER,1,<domain>,<port># E.g.:SERVER,1,gps.whatsgps.com,6801,0# |
Please move to the network service provider service area |
| 2 | APN,<use_apn># E.g.:APN,internet# |
Set APN |
| 3 | TIMER,T# | T:The range of T is 5-900 second. The default reporting interval is T second after setting |
6.2. Query command
| 1 | PARAM# | Query device parameters |
| 2 | STATUS# | Set APN |
| 3 | WHERE# | Query latitude and longitude |
| 4 | RESET# | evice restart |
6.3. Alarm mode setting and description
| 1 | Vibration alarm SENALM,A,M# |
A=ON/OFF, turn on or turn off the alarm, the default is off M=0/1/2, alarm mode, 0: GPRS only; 1: SMS+GPRS; 2: GPRS+SMS+PHONE |
| 2 | Power off alarm POWERALM,A,M# |
A=ON/OFF, turn on or turn off the alarm, the default is off M=0/1/2, alarm mode, 0: GPRS only; 1: SMS+GPRS; 2: GPRS+SMS+PHONE |
| 3 | ACC alarm ACCALM,A,B,M# |
A=ON/OFF, turn on or turn off the alarm, the default is off B=1/2/3, 1 is ACC ON alarm, 2 is ACC OFF alarm, 3 is ACC ON + ACC OFF alarm M=0/1/2, alarm mode, 0: GPRS only; 1: SMS+GPRS; 3: GPRS+SMS+PHONE |
| 4 | Displacement alarm MOVING,A,R,M# |
A=ON/OFF, turn on or turn off the alarm, the default is off R=100-1000, moving distance, unit: meter, default is 300 M=0/1/2, alarm mode, 0: GPRS only; 1: SMS+GPRS; 3: GPRS+SMS+PHONE |
| 5 | Over speed alarm SPEED,A,B,M# |
A=ON/OFF, turn on or turn off the alarm, the default is off B=1-255 (Km/h), the overspeed threshold, the default is 100 (Km/h) M=0/1/2, alarm mode, 0: GPRS only; 1: SMS+GPRS; 3: GPRS+SMS+PHONE |
6.4. SOS and Center Number Setting
| 1 | SOS setting SOS,A,phone1,phone2,phone3# |
The SOS number can be set to 1-3 numbers. Note: When the number already exists, using this command will clear the previously set number and replace it with a new SOS number |
| 2 | Center number setting CENTER,A,phone number# |
Add center number, only center number and SOS number can be set |
6.5. Remote oil cut
| 1 | Remote oil cut RELAY,1# |
When the car speed reaches below 20KM/H, the command will be executed successfully |
| 2 | Remote oil restore RELAY,0# |
Restore the oil circuit |
7. Installation diagram
The diagram shows a car with labels indicating recommended installation locations for the GPS tracker: "Under decorative panel", "Around the dashboard", and "Under the rear windshield".
8. Troubleshooting
When operating the terminal, if you feel that the equipment is abnormal, please refer to the following problems and solutions. If the problem still cannot be solved, please contact the seller or service provider.
| Common Problem | Reason | Solution |
|---|---|---|
| Bad Signal | When using the terminal in areas with poor signal reception, such as near high-rise buildings or basements, radio waves cannot be effectively transmitted | Use the terminal in a location with good signal |
| Unable to connect to the network | SIM card is not installed | Check the SIM card |
| Dirt on the metal surface of the SIM card | Wipe with a clean cloth | |
| Invalid SIM card | Contact your internet service provider | |
| Out of GSM service area | Please move to a place with strong signal and try again | |
| Unable to connect to the network | Weak signal | Please move to a place with strong signal and try again |
| Please confirm whether the device is switched on | Turn on the device battery switch | |
| Please check if the SIM is installed | SIM card: Please install the SIM card | |
| Switch off | Poor contact | Check if the plug is connected |
Warranty card
Maintenance record
| Maintenance shop | |
| Sending date | |
| Fault description | |
| Maintenance situation | |
| IMEI number | |
| Maintenance person |
Maintenance record
| Maintenance shop | |
| Sending date | |
| Fault description | |
| Maintenance situation | |
| IMEI number | |
| Maintenance person |
FCC Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
whatsgps.com
