Statement
Thank you very much for using the R12L vehicle terminal (mobile user terminal) product. Please read this manual carefully before use. Please pay attention to all the cautions and warnings mentioned in the manual. Please keep this manual properly for reference.
This manual, as well as the description of the software, can be used or copied directly after receiving the license, only in accordance with such authority.
The content of this manual is to provide information for use, subject to change without notice, and should not be regarded as a commitment by SEEWORLD. SEEWORLD assumes any liability or any deviation of legal liability may appear in this book.
SEEWORLD Company reserves the right to make changes to specifications at any time without notice. SEEWORLD Corporation believes that this manual is accurate and reliable. However, SEEWORLD Corporation is not responsible for its use, or infringement of patents or the rights of other third parties caused by its use. Without a license, any patents or patent rights will belong to SEEWORLD.
1. Product Introduction
The R12L positioning terminal is a feature-rich positioning terminal with a wide application range. The equipment adopts the AT6558R chip and supports the GPS and Beidou satellite systems. In addition to supporting satellite positioning, the equipment also supports single base station and base station positioning. For expansion of rich functions, please refer to the following related descriptions about extended functionality. Integrated with independent research and development of the hardware control circuit, it makes the equipment work reliably and stably long-term, and can automatically recover when abnormal.
2. Main Function
- GSM quad-frequency, built-in GSM/GPS antenna;
- Chip Specification: 4G Cat1, Support 2&4G
- Support all deployed and soon to be operational global navigation satellite systems GPD, Beidou
- Support global multi-base station and satellite positioning mode
- Low Voltage Input: 9-100V
- Built-in high-power surge protection circuit;
- The use of high temperature resistant safety explosion-proof type rechargeable lithium cobalt acid battery
- Built-in high-power surge protection circuit;
- Built-in hardware monitoring circuit, abnormal state automatic recovery
- Remotely oil control
- ACC Detection
- Power off Alarm
- Vibration Alarm
- Movement Alarm
- Over-the Air (OTA)
- Waterproof IP65
3. Specification
| Items | Specifications | Remark |
|---|---|---|
| Working Voltage | DC9V-100V | Not charging |
| Working current | 50mA @12V (static current 5mA) | |
| Device size | L82mm *W35mm*H14mm | |
| Position model | GPS+BD+LBS | |
| Positioning accuracy | <5 Meters | |
| communication network | GPRS | |
| LTE-FDD LTE-TDD | C: B1/B3/B5/B8/B34/B38/B39/B40/B41 EU: B1/B3/B5/B7/B8/B20 SA: B1/B2/B3/B4/B5/B7/B8/B28/B66 |
|
| GSM | 850/900/1800/1900MHz | |
| GPRS | TCP | |
| Working Temperature | -20°C~+70°C | |
| Working Humidity | 5% ~ 95% | |
| Working Time | 0.5h | |
| Warranty | 1 year |
4. Appearance Diagram
The R12L GPS tracker has the following visible components:
- Power Cable: Connects the device to the power source.
- GPS Ceramic Antenna: Internal antenna for GPS signal reception.
- Sim card interface: Slot for inserting a SIM card.
- Battery Switch: A switch to control the internal battery.
- LED Indicators: Three indicator lights labeled Red, Blue, and Green, which provide status information.
By viewing the status indicator lights, users can understand the performance of the equipment. The meanings are as follows:
| LED Models | LED Light Status | Meaning |
|---|---|---|
| Blue | Fast flash | GSM initialization |
| Slow flash | GSM receiving signal is normal | |
| Normally on | GSM/GPRS online | |
| Not Bright | No GSM signal received/no card inserted | |
| Green | Fast flash | BD/GPS signal search |
| Normally on | BD/GPS Successful positioning | |
| Not Bright | GPS is dormant/not working | |
| Red | Normally on | Switch on the external power supply |
| Not Bright | Disconnect the external power supply |
5. Install Statement
5.1. Wiring definition
The device wiring utilizes color-coded cables for specific functions:
| End Definition | Color | Instruction |
|---|---|---|
| MOTOR | Yellow | Cut oil wire |
| ACC | Orange | ACC wire |
| V- | Black | 12V/24V Ground |
| V+ | Red | Connect to Power of 12V/24V |
Relay Connection Matters Needing Attention:
For castor oil joints, connect the relay using the line (85) and thin yellow line (86). The white line (85) is connected to the vehicle power supply (12V). The yellow line's relay control line is connected to the equipment. To cut off the pump, cut the positive cable of the pump. Then, series connect to the relay normally closed contacts (87a) green thick line. The other end is connected to the relay COM contact (green thick line 30).
6. Setting Common Command List
6.1. Setting Common Command List
| # | Command | Description |
|---|---|---|
| 1 | SERVER,8520,IP,PORT# | T: primary server IP port, F: vice server port, *: interval operator (IP forwarding only master server data) |
| 2 | TIMER,T1# | T1: ACCON Back interval |
6.2. Setting Common Command List
| # | Command | Description |
|---|---|---|
| 1 | STATUS# | Query Status |
| 2 | FACTORY# | Restore Factory |
| 3 | RESET# | Restart Device |
6.3. Remotely cut off oil & power
| # | Command | Description |
|---|---|---|
| 1 | Remotely cut off oil RELAY,1# | When the car speed down to 20 km/H, the instruction execution success |
| 2 | Recovery oil RELAY,0# | Recovery oil |
7. Installation Instruction
The R12L GPS tracker can be installed in several locations within a vehicle for optimal performance and discretion:
- Under decorative panel: Concealed placement behind interior trim panels.
- Around the dashboard: Integrated discreetly within the dashboard area.
- Under the rear windshield: Mounted on the underside of the rear window.
8. Trouble shooting
In the operation of the terminal, if the equipment is not normal, please refer to the following problems and solutions. If the problem still cannot be solved, please contact the seller or service provider.
| Common Problem | Reason | Solution |
|---|---|---|
| Poor Reception | When terminals are used in areas with poor reception, such as near tall buildings or basements, radio waves cannot be transmitted effectively. | Use terminal in the signal of good position. |
| SIM card is not installed | Check the SIM card. | |
| SIM card metal surface dirt | Wipe with a clean cloth. | |
| SIM card is invalid | Contact your network service provider. | |
| Unable to connect to the network | Beyond the GSM service area. | Please move to the network service provider service area. |
| Weak signal | Please move to a place with strong signal and try again. | |
| Power Off | Please confirm whether the equipment is turned on the switch. | Open the battery switch equipment. |
| Please check the SIM is installed. | Please insert the SIM card. | |
| Poor contact | Check whether the plug is connected well. |
Warranty card
This section provides fields for maintenance records.
| Maintenance Record | Details |
|---|---|
| Maintenance shop | |
| Sending date | |
| Fault description | |
| Maintenance situation | |
| IMEI number | |
| Maintenance person |
(Repeat for second maintenance record)
| Maintenance Record | Details |
|---|---|
| Maintenance shop | |
| Sending date | |
| Fault description | |
| Maintenance situation | |
| IMEI number | |
| Maintenance person |
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
