Craftsman Snow Thrower Model 247.88848 Parts List

Parts Identification

Ref. No.	Part No.	Description
1	05244B	Housing, Bearing
2	784-0315A	Housing, Bearing
3	918-04514	Gear Box Assembly, Auger
4	918-0281A	Bracket Assy, Auger Brake
5	684-0090B-0637	Impellar, 16"
6	684-04224-0691	Housing, Auger - 45"
7	684-04151-4028	Spiral Assy, LH
8	684-04152-4028	Spiral Assy, RH
9	710-1245B	Screw, 5/16-24 x .875
10	710-0389	Bolt, Carriage, 3/8-16 x .750
11	710-0451	Screw, Carriage, 5/16-18 x .75
12	710-0347	Screw, Hex Cap, 3/8-16 x 1.75
13	710-0376	Screw, Hex Cap, 5/16-18 x 1.00
14	710-04484	Screw, 5/16-18 x .750
15	926-04012	Nut, Push
16	929-0071A	Extension Cord, 110V
17	710-3168	Bolt, Carriage, 3/8-16 x 1.0
18	710-04606A	Screw, 5/16-18 x .4300
19	911-0677	Ferrule
20	917-0299	Gear, Worm, Dbl Thread
21	712-04063	Nut, Flnge Lk, 5/16-18
22	712-04065	Nut, Flg Lk, 3/8-16
23	941-0217	Sleeve
24	936-0291	Washer, Flat, .88 ID x .38 OD
25	914-0126	Key, Hi Pro, 3/16 x 3/4
26	914-0135	Key, Woodruff,1/4 x 3/4
27	714-04040	Pin, Bowtie Cotter
28	915-0118	Pin, Spirol, 5/16 x 1.75
29	725-0157	Tie, Cable
30	731-1696B	Adapter, Chute, 6”
31	738-0275	Shaft, Gear, Worm
32	731-05163	Spacer, 1.0 x 1.5 x 1
33	731-2635	Clip, Mounting
34	931-2643	Tool, Cleanout
35	732-0858	Spring, Extension
36	936-0159	Washer, .349 x .879 x .063
37	736-0174	Washer, .625 x .885 x .015
38	736-0505	Washer, Flat, .34 x 1.50 x .150
39	950-04020	Spacer, 1.004 x 1.375 x .25
40	921-0146	Oil Seal
41	936-3008	Washer, .344 x .75 x .12
42	736-3046A	Washer, 1.01 x 1.86 x .06
43	938-0281	Screw, Shoulder, .625 x .17
44	738-04155	Pin, Shear, .25 x 1.75
45	738-04159	Axle, Spiral, 45"
46	741-0192	Bearing, Flange w/Flats
47	941-04024	Bearing, Self Aligning
48	941-0475	Bushing, Nylon
49	741-0494	Bushing, Flange, 1.051 x 1.16
50	747-0980A	Rod, Auger Idler
51	721-0325	Plug
52	954-04194A	V Belt,4L x 44.60" Long
53	756-0178	Pulley, Flat Idler, 2.75 OD
54	756-04244A	Pulley, Auger Drive, 10.0
55	784-0385C	Bracket, Auger Idler
56	790-00264A-0637	Bracket, Gear Box Support
57	921-0145	Seal, Oil
58	936-0266	Washer, Flat, 1.52 ID x 2.0 OD
59	790-00181	Drift Cutter
60	790-00280-0637	Plate, Shave, 45"
61	741-0184	Bearing, Thrust
62	784-5697-0637	Shoe, Skid
63	749-04384-0637	Support Tube
64	710-3008	Screw, 5/16-18 x .75
65	748-04067A	Pulley, Adapter, .75 Dia.
66	918-0246	Hsg Assy Auger RH (Inc. 40 & 70)
67	918-0247	Hsg Assy Auger LH (Inc. 40 & 70)
68	710-1260A	Screw, LD, 5/16-18 x .750
69	711-04714	Shaft, Drive, Auger
70	741-0670	Flange Bearing
71	716-0111	Ext, Ret, Ring
72	917-1425	Gear, Worm, LH
73	937-3000	Lube Fitting, 3/16 #70
74	736-0188	Washer, .76 x 1.49 x .06
2	618-0279P	Dogg, Steering Drive, LH
3	618-0280P	Dogg, Steering Drive, RH
4	918-0282E	Shaft Assembly, Steering
5	918-04178	Assembly, Friction Wheel
6	718-04034	Wheel, Friction, Bonded
7	710-0896	Screw, Hex Wash
8	684-0118B-0637	Bracket, Auger Actuator
9	684-0119B-0637	Bracket, Drive Actuator
10	684-0161-0637	Arm, Shift
11	984-04103	Rod Assembly, Shift
12	684-04212-0637	Bracket, Friction Drive Support
13	684-04235	Sprocket, 32T
15	710-0538	Screw, Hex Cap Lock,
21	711-04605	Shaft, Actuator
23	912-0138	Nut, Hex, 1/4-28 GR5
25	713-0284	Chain, Endless, #41 x 36L
26	713-0286	Chain, #420 x 40L
27	913-04015	Sprocket, #41 x 10T
33	716-04048	Ring, Retainer
34	917-0302	Plate, Drive
38	936-0158	Washer, Lock, 5/8
40	936-0300	Washer, .406 x .875 x .059
41	936-0329	Washer, Lock, 1/4
42	711-04615	Pin, Clevis
43	914-0149B	Pin, Internal Cotter
44	937-3000	Fitting, Lube, 3/16 Drive
45	738-0143	Screw, Shldr., .498 x .34
46	738-0279	Spindle, Drive Plate
47	738-0292A	Screw, Hex Shldr., 1/4-28
48	741-0163A	Ass'y, Bearing/Housing
50	741-04108	Bearing, Hex Flange
51	941-0563	Bearing, Ball
52	741-0747	Bush, Flg, .5625 ID x 1.375 x .4375
53	741-0748	Bush, Flg, .5 ID x .627 OD
54	746-04337A	Cable, Steering
55	946-0951A	Cable, Auger Idler
56	747-0973	Rod, Drive Clutch
57	750-04703	Spacer, 1.01 x 1.50 x .93
58	750-04717	Spacer, .49 x 7.865
59	750-04718	Spacer, .49 x 3.545
60	750-05342	Spacer, .566 x .87 x .190
61	750-05343	Spacer, .566 x .87 x 1.25
62	750-0903B	Spcr., .514 x .632 x 2.44
63	950-0997	Spacer, .675 x 1.0 x .23
64	750-1302B	Spcr, .6725 x 1.125 x 2.48
65	756-0344	Pulley, Drive
66	756-0625	Roller, Cable
67	784-0404	Retainer Bracket
68	784-0406A-0637	Bracket, Frame Support
69	784-0407-0637	Bracket, Axle Support
70	790-00257-0691	Cover, Upper Frame
71	790-00259-0691	Cover, Lower Frame
72	790-00349-0691	Trans Frame
73	684-04169	Idler Pulley Assembly
74	710-0157	Screw, Hex 5/16-24 x .75
75	710-0191	Screw, Hex 3/8-24 x 1.25
76	710-0607	Screw, Hx Wash Hd Tapp
77	710-0624	Screw, Hex Cap, 5/16-24 x 1.50
78	710-0654A	Screw, 3/8-16 x 1.00
79	710-0809	Screw, 1/4-20 x 1.25
80	738-04439	Screw, Hex Cap, 5/16-24 x .875
82	714-0118	Key, Square, 1/4 x 1.5
84	931-2531	Cover, Belt
85	732-04308A	Torsion Spring, .850 dia. x .333 lg.
86	936-0119	Washer, Lock, 5/16
87	736-0247	Washer, Flat, .406 x 1.25
88	736-3092	Washer, Flat, .265 x 1.0 x .030
89	952Z490-SUA	Engine Complete
90	748-04112A	Shoulder Spacer, .3175 x .500 x .094
91	750-04571	Shoulder Spacer, .260 x .785 x .538
92	750-04821	Shoulder Spacer, .340 x 1.00
93	750-05316	Spacer, 1.02 x 1.63 x .1425
95	954-04202	V Belt, 3/8 x 36.68
96	756-04224	Pulley, Flat Idler, 2.75 OD
97	756-0241B	Double Pulley, 3.25 x 2.75
98	784-0385D	Bracket, Auger Idler
99	790-00167A-0637	Belt Keeper Bracket
100	790-00208C	Idler Drive Wheel Bracket
101	790-00254A-0637	Belt Cover Bracket
102	634-0225A-0911	Wheel Ass'y. - LH
102	634-0226A-0911	Wheel Ass'y. - RH
102	734-2031	Tire
102	734-1124A-0662	Rim Assembly
102	934-0255	Valve
103	711-04606A	Axle, Wheel, 45"

Operational Labels and Instructions

777122386 AUGER CONTROL: STOP, GO, LEFT TURN TRIGGER CONTROL, CHUTE DIRECTIONAL CONTROL (DISCHARGE LEFT, DISCHARGE RIGHT)

777122387 CHUTE TILT CONTROL: Labels 1-6 for tilt positions, R for reverse tilt.

777122388 DRIVE CONTROL: STARTING INSTRUCTIONS: 1. INSERT KEY AND SNAP IN PLACE. 2. MOVE THROTTLE CONTROL TO "FAST" POSITION. 3. MOVE CHOKE CONTROL TO "CHOKE" POSITION. PUSH PRIMER 3x. 4. ROPE START: PULL SLOWLY UNTIL HARDER TO PULL, THEN PULL RAPIDLY TO START. REPEAT PRIMING IF NEEDED. ELECTRIC START: DO NOT USE IN RAIN. CONNECT POWER CORD AND PUSH STARTER BUTTON. REPEAT PRIMING IF NEEDED. 5. MOVE CHOKE CONTROL SLOWLY TO "RUN" POSITION. 6. TO STOP ENGINE: MOVE THROTTLE TO "STOP" POSITION.

777S32236 DANGER LABEL: NEVER PUT HAND IN CHUTE. CONTACT WITH ROTATING PARTS CAN AMPUTATE FINGERS AND HANDS. SHUT OFF ENGINE AND WAIT UNTIL ALL MOVING PARTS HAVE STOPPED BEFORE UNCLOGGING. USE CLEAN-OUT TOOL OR WOODEN STICK TO UNCLOG DISCHARGE CHUTE.

777S32636 DANGER LABEL: KEEP AWAY FROM ROTATING IMPELLER AND AUGER. CONTACT WITH IMPELLER OR AUGER CAN AMPUTATE HANDS AND FEET. USE CLEAN-OUT TOOL TO UNCLOG DISCHARGE CHUTE. DISENGAGE CLUTCH LEVERS, STOP ENGINE, AND REMAIN BEHIND HANDLES UNTIL ALL MOVING PARTS HAVE STOPPED BEFORE UNCLOGGING OR SERVICING MACHINE. TO AVOID THROWN OBJECTS INJURIES, NEVER DIRECT DISCHARGE AT BYSTANDERS. USE EXTRA CAUTION WHEN OPERATING ON GRAVEL SURFACES.

777122363 DRIVE AUGER LOCK: STOP, R, 1, 2.

777D13775 LABEL: CRAFTSMAN PROFESSIONAL OVERHEAD VALVE 420CC

777D13770 LABEL: CRAFTSMAN PROFESSIONAL

777X43688 LABEL: DO NOT USE E85 OR FUEL CONTAINING MORE THAN 10% ETHANOL TO AVOID ENGINE DAMAGE.

777D11503 LABEL: CRAFTSMAN PROFESSIONAL 45" CLEARING WIDTH ELECTRIC START

	Craftsman 45" Snow Thrower Operator's Manual Comprehensive operator's manual for the Craftsman 45" Snow Thrower, Model No. 247.88848. Includes safety instructions, assembly, operation, maintenance, and troubleshooting.
	Craftsman 22-Inch Electric Start Snow Thrower Model 247.887791 Parts List Official parts list and essential operating information for the Craftsman 22-inch Electric Start Snow Thrower, Model 247.887791. Includes safety warnings and starting instructions.
	Craftsman 26" Snow Thrower Operator's Manual (Model 247.889720) Operator's manual for the Craftsman 26" Snow Thrower, Model 247.889720. Contains essential safety instructions, assembly procedures, operation guidelines, maintenance schedules, troubleshooting tips, and warranty information.
	Craftsman 30" Snow Thrower Operator's Manual This operator's manual provides essential safety, assembly, operation, and maintenance instructions for the Craftsman 30" Snow Thrower, Model No. 247.888301. Learn how to safely operate and maintain your snow thrower for optimal performance.
	CRAFTSMAN 247.885550 Operator's Manual: 22-Inch 4-Cycle Snow Thrower Operator's manual for the CRAFTSMAN 247.885550 22-inch 4-cycle electric start snow thrower, covering safety, assembly, operation, maintenance, and troubleshooting.
	Craftsman 24" Snow Thrower Operator's Manual: Safety, Operation, Maintenance This comprehensive operator's manual provides essential information for the safe and effective use of the Craftsman 24" Snow Thrower (Model C459-52222). It covers critical safety instructions, assembly procedures, detailed operation guidelines, maintenance schedules, troubleshooting tips, and warranty information. Learn how to properly operate, maintain, and store your snow thrower for optimal performance and longevity.
	Craftsman C950-52930-0 Dual Stage Snow Blower Owner's Manual This owner's manual provides essential safety instructions, operation guidelines, maintenance procedures, and troubleshooting tips for the Craftsman C950-52930-0 Dual Stage Snow Blower. Learn how to safely assemble, operate, and maintain your snow blower for optimal performance.
	Craftsman Mower 247.374300 Parts List and Engine Components Comprehensive parts list for the Craftsman Mower Model 247.374300, including detailed breakdown of engine components for Model 09P602-0039-F1. Find part numbers and descriptions for all mower and engine parts.

Craftsman Snow Thrower Model 247.88848 Parts List

Parts Identification

Operational Labels and Instructions

Related Documents