Operator's Manual
CRAFTSMAN
Electric Start 22-INCH SNOW THROWER
Model No. 247.887791
Form No. 769-05101A, Date: 6/11/2010
Safety Information
DANGER
Keep away from rotating impeller and auger. Contact with impeller or auger can amputate hands and feet.
Use clean-out tool to unclog discharge chute.
Disengage clutch levers, stop engine, and remain behind handles until all moving parts have stopped before unclogging or servicing machine.
To avoid thrown objects injuries, never direct discharge at bystanders. Use extra caution when operating on gravel surfaces.
Read operator's manual.
DANGER
Never put hand in chute. Contact with rotating parts can amputate fingers and hands.
Shut off engine and wait until all moving parts have stopped before unclogging.
Use clean-out tool or wooden stick to unclog discharge chute.
DANGER
Do not use E85 or fuel containing more than 10% ethanol to avoid engine damage.
Starting Instructions
- Insert key and snap in place.
- Move throttle control to the "FAST" position.
- Move choke control to the "CHOKE" position. Push primer 3 times.
- Rope Start: Pull slowly until harder to pull, then pull rapidly to start. Repeat priming if needed.
- Electric Start: Do not use in rain. Connect power cord and push starter button. Repeat priming if needed.
- Move choke control slowly to the "RUN" position.
- To stop engine: Move throttle to the "STOP" position.
Parts List - Snow Thrower Components
The following table lists key components of the Craftsman 22-inch Snow Thrower. For a complete list including engine parts, refer to the original manual.
| Ref. No. | Part Number | Description |
|---|---|---|
| 1 | 984-04037 | Chute Assembly |
| 2 | 710-04071 | Carriage Bolt 5/16-18 x 1.0" |
| 3 | 710-0451 | Carriage Bolt 5/16-18 |
| 4 | 710-0260A | Carriage Bolt 5/16-18 x .62 |
| 5 | 720-04072AA | Wing Knob 5/16-18 |
| 6 | 731-04388A | Chute Handle |
| 7 | 731-04426A | Upper Chute |
| 8 | 936-0267 | Flat Washer .385 x .87 x .06 |
| 9 | 931-04127 | Lower Chute |
| 10 | 931-04353 | Chute Ring |
| 11 | 931-2636A | Chute Adapter 5" Dia. |
| 12 | 932-04111 | Chute Adjustment Spring |
| 13 | 712-04064 | Flange Lock Nut 1/4-20 |
| 14 | 931-2643 | Clean-out Tool |
| 15 | 731-2635 | Clean-out Tool Mount |
| 16 | 725-0157 | Cable Tie |
| 17 | 710-0134 | Carriage Screw 1/4-20 x 0.62" |
| 18 | 710-0520 | Hex Bolt 3/8-16 x 1.50" |
| 19 | 710-04484 | AB Screw 5/16-18 x .750 |
| 20 | 712-04063 | Flange Lock Nut, 5/16-18 |
| 21 | 712-04065 | Flange Lock Nut, 3/8-16 |
| 22 | 750-04852 | Shoulder Spacer |
| 23 | 715-04020 | Spiral Pin |
| 24 | 926-04012 | Push On Nut |
| 25 | 731-04218B | Impeller |
| 26 | 932-0611 | Extension Spring |
| 27 | 736-0174 | Wave Washer |
| 28 | 938-0281 | Shoulder Screw 3/8-16 |
| 29 | 941-0245 | Hex Flange Bearing |
| 30 | 941-0309 | Ball Bearing |
| 31 | 950-04191 | Spacer |
| 32 | 684-04358 | Flat Idler |
| 33 | 784-0434-0637 | Auger Idler Bracket |
| 34 | 790-00075 | Bearing Housing |
| 35 | 918-04292B | Auger Gearbox Assembly |
| 36 | 684-04113A-0637 | Auger Assembly - LH |
| 37 | 684-04114A-0637 | Auger Assembly - RH |
| 38 | 684-04166A-4044 | Auger Housing, 22" |
| 39 | 714-04040 | Bow Tie Cotter Pin 72 |
| 40 | 731-04870 | Spacer, 1.25 x.75 x 1.00 |
| 41 | 936-0351 | Flat Washer |
| 42 | 738-04124A | Shear Pin,.25 x 1.50 |
| 43 | 741-0493A | Flange Bushing |
| 44 | 790-00087A-0637 | Hex Bearing Housing |
| 45 | 790-00117-0637 | Shave Plate 2.25 x 21.66 LG |
| 46 | 784-5580-4044 | Skid Shoe |
| 47 | 710-04606A | Belt Keeper |
| 48 | 929-0071A | Extension Cord |
The document also includes detailed parts lists for the Craftsman Engine Model 265-SU, which is used in this snow thrower.
Diagrams
The manual includes several diagrams illustrating the assembly of the snow thrower and its engine components. These diagrams are referenced by part numbers in the lists above.
- An exploded view diagram shows the overall assembly of the snow thrower, detailing the placement of various parts like the chute, auger, and handles.
- Another diagram provides a detailed view of the engine, illustrating its internal and external components.
- Specific diagrams focus on sub-assemblies such as the auger mechanism and the engine controls.
Illustrations also indicate specific operational notes, such as the purpose of certain parts for turning versus lifting, and safety precautions.
