Proscenic User Manual

Important Safety Instructions

To reduce the risk of injury or damage, keep these safety precautions in mind when setting up, using and maintaining your robot vacuum cleaner:

• Read all safety and operating instructions before operating your robot.
• Retain the safety and operating instructions for future reference.
• Pay attention to all warnings on your robot, battery, charging dock and in the user manual.
• Follow all operating and use instructions.
• The external flexible cable or cord of the power supply unit cannot be replaced; if the cord or plug is damaged, the power supply unit shall be disposed of.
• This product is designed to be plugged into a standard outlet only. Product may not be used with any type of power converter. Use of power converters will immediately void the warranty.
• CAUTION: Only charge one of the following robot batteries: maximum 14.4V, max 2600mAh Ni-MH or maximum 2600mAh Li-ion battery. Other types of batteries may burst causing injury. Always contact Customer Care for the correct replacement of your battery.
• Always charge and remove the battery from your robot and accessories before long-term storage or transportation.
• The battery must be removed from this device before this device is disposed of. To remove the battery from this device, first remove the screws on the bottom, then remove the main PCB and unscrew the battery cover by using a screwdriver. Remove the battery by disconnecting the quick connector.
• WARNING: Chemical Exposure: If the battery pack is leaking, do not allow the liquid to come in contact with skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice. Place the battery (the used battery pack included when the robot will be disposed) in a sealed plastic bag and dispose of safely according to local environmental regulation.
• WARNING: Fire or Explosion Hazard: Do not crush or dismantle battery packs. Do not heat or place the battery pack near any heat source or direct sunlight. Do not incinerate or short-circuit the battery pack. Do not subject batteries to mechanical shock.
• Contact your local waste management authority for battery recycling and disposal regulations in your area.
• Your robot is not a toy. Do not sit or stand on robot. Children and pets should be supervised when your robot is operating.
• Robot is for indoor use only.
• Do not use non-rechargeable batteries. Use only the rechargeable battery supplied with the product. For replacement, purchase identical robot battery or contact robot Customer Care for alternative battery options.
• Store and operate robot in room temperature environments only.
• Do not spray or pour liquids on your Robot.
• Do not use any other power supply cord. For replacement cords, please contact Customer Care to ensure proper selection of country specific power supply cord.
• Do not use robot to pick up sharp objects, glass, or anything that is burning or smoking.
• Do not immerse the battery pack in any liquid.
• Do not use robot to pick up spills of water, bleach, paint, or other chemicals, or anything wet.
• Before using robot, pick up objects like clothing, loose papers, pull cords for blinds or curtains, power cords, and any fragile objects. If robot passes over a power cord and drags it, there is a chance an object could be pulled off a table or shelf.
• If the room to be cleaned contains a balcony, a physical barrier should be used to prevent access to the balcony and ensure safe operation.
• Do not place anything on top of your robot.
• Be aware that the robot moves on its own. Take care when walking in the area that the robot is operating in to avoid stepping on it.
• Do not operate the robot in areas with exposed electrical outlets in the floor.
• Do not use this device on an unfinished, unsealed, waxed or rough floor. It may result in damage to the floor and this device. Use only on hard floor surfaces or low pile carpet.
• This device has been designed to be used on floors without scratching them. We still recommend that you test this device on a small area of the room to be cleaned to ensure no scratches are made before cleaning the whole room.

Battery and Charging Information

Lithium-ion Battery

Important: Lithium-ion batteries and products that contain Lithium-ion are subject to stringent transportation regulations. If you need to ship this product (with the battery included) for service, travel or any other reason, you MUST comply with the following shipping instructions:

• Remove the Lithium-ion battery from the product.
• Place a piece of tape over the battery's metal charging contacts.
• Reinstall the battery (with the tape on it) in the product and secure the battery door.
• Package the product in its original packaging or in your own packaging that prevents any movement during transportation.
• Ship via ground transportation only (no air shipping).

Battery Storage

If storing robot off the charging dock, remove the battery first. Then store robot and the battery in a cool, dry place.

The symbol on the product or its packaging indicates:

Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local authority for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being. Please contact your local or regional waste authority for more information on collection, reuse and recycling programs.

1. About Your Robot

1.1 Robot

Auto cleaning Start/Stop button: Press to start cleaning.

Auto-recharging button

[Image of the top of the Proscenic 850T robot vacuum with labels for Auto cleaning Start/Stop button and Auto-recharging button]

1.2 Charging Dock

[Image of the Proscenic 850T charging dock with labels for Signal Transmission Area, Charging Indicator, and Charging Contact Pins]

1.3 Remote Control

[Image of the Proscenic 850T remote control with labels for Mode and Time Display Screen, Return to Charging Dock, Start/Stop, Schedule Setup, Edge Cleaning, Power levels, Auto Cleaning, Direction/Clock Setting, Time Setup, Spot Cleaning, Single Room Cleaning]

Install 2 AAA batteries before using the remote control for the first time. Make sure the positive and negative ends are facing the correct polarity direction as marked in the battery compartment. When using the remote control, please aim at the robot and the effective distance is 0-5m.

1.5 LED Indicator

2. Using Your Robot

2.1 Quick Start

1. Plug in the charging dock, and take the rest wire into the trunking at the bottom of charging dock.
   Note: If you don't put the rest wire into the trunking, it may stuck the robot while charging or cleaning. [Image showing wire management in the charging dock]
2. Charging Dock Position
   1) Place the charging dock on a hard, level surface and against a wall. [Diagram showing correct and incorrect charging dock placement relative to walls and obstacles]
   2) Place the charging dock against the wall and make sure the place is open & uncluttered area leaving at least:
   • 2 meters (6.5 feet) in front of the charging dock;
   • 1 meter (2.3 feet) on both sides of the charging dock. [Diagram illustrating required clearance around the charging dock]
   3) Connect the round connector of the adapter into the power socket on the charging dock and the other end into a wall outlet.
   Note: Please make sure the indicator light is on when the charging dock is plugged in, otherwise the robot cannot be charged. [Image showing adapter connection to charging dock and wall outlet]
3. Install Side Brushes
   Attach side brushes to the bottom of robot by pressing a brush into each slot. [Image showing side brushes being attached to the robot]
4. Turn on the main power switch on the bottom of robot. [Image showing the power switch on the bottom of the robot]
5. Activate the Robot
   Place robot onto the charging dock, making sure the metal charging contacts on the charging dock match up with those underneath the robot. If successful, you will hear a series of tones. [Image showing robot being placed on the charging dock]
6. Start Cleaning Cycle
   • Press the power button once to wake up the robot.
   • Press the AUTO button or the power button on the remote control to start a cleaning cycle. [Image showing remote control buttons for starting cleaning]
7. Pause
   • To pause the robot during a cleaning cycle, press the button or press the II button on remote control.
   • To start the robot, press the button or press the ►II button on remote control. [Image showing remote control buttons for pausing and resuming cleaning]
8. Power OFF
   • To end the cleaning cycle and put robot in standby mode, press and hold the button until robot indicators turn off. [Image showing robot in standby mode]

2.2 How Robot Clean Your Home

1. Auto Cleaning
   • Press the button on robot or press the AUTO button on remote control to start auto cleaning.
   • If the battery is low while the cleaning is not finished, the robot will return to the charging dock for charging.
   Warm Tips: During the recharging process, there may be a phenomenon that the charging dock cannot be found. At this time, the robot will flash red light and “BEEP” four times. Please manually put the robot onto the charging dock to charge. [Image showing robot performing auto cleaning and returning to dock]
2. Spot Cleaning
   When you select spot cleaning, robot intensely cleans a localized area by spiraling outward about 3 feet (1 meter) in diameter and then spiraling inward to where it started. When spot cleaning, robot boosts vacuum power to provide the best cleaning possible where you need it. To use spot cleaning, place robot on top of the localized debris and press Θ (Spot) on the remote control. [Image showing robot performing spot cleaning]
3. Power levels
   1.When the robot vacuum cleaner is in sweeping mode, press this button to adjust the suction power;
   2.When the robot vacuum cleaner is in sweeping and mopping simultaneous mode, press this button to adjust the suction power;
   3.When the robot vacuum cleaner is in mopping mode, press this button to adjust the speed of the water output. [Image showing remote control buttons for adjusting power levels]
4. Edge Cleaning
   After robot finishes cleaning the open areas of your floor, it uses edge clean to ensure that it has cleaned along walls and around furniture Legs. If you prefer a quicker edge cleaning, press the Π button on remote control. [Image showing robot performing edge cleaning]
5. Single Room Cleaning
   Press the button 合 on the remote control to start random cleaning.
   Warm Tips: In this mode, the robot will keep cleaning for about 30 minutes and then stop. Please close the door to ensure the robot will not go out the room. [Image showing robot performing single room cleaning]
6. Floor Mopping Cleaning
   Robot is equipped with a water tank so that it can clean your home in floor mopping cleaning mode.
   • Attach the cloth and fill in the water tank with water.
   • Remove the dust bin.
   • Put the water tank back to robot and start the robot.
   Note: If you are using a dry sweeping cleaning mode, skip the step of filling water. [Images showing attachment of cloth, filling water tank, and placing water tank back on robot]

2.3 Cleaning Schedule

Robot has cleaning schedule settings which allow you to customize when Robot cleans your home.

1. Set the Remote Control's Clock
   [Image sequence showing how to set the clock on the remote control]
   Press button on remote control, and then the hour section begins to flash in the clock display setting window.
   Press the or button to select the minute or hour section. Press or button to select the desired figures.
   And then press the button, the robot will “BEEP” when the clock setting completed.
2. Setting Cleaning Schedule
   [Image sequence showing how to set a cleaning schedule on the remote control]
   Press button on remote control, and then the hour section begins to flash in the cleaning schedule display setting window.
   Press the or button to select the minute or hour section. Press or button to select the desired figures.
   And then press the button, the robot will “BEEP” when the cleaning schedule setting is completed.
3. Cancel the Cleaning Schedule
   Press and hold button approximately 4 seconds on remote control, the robot will “BEEP” when the cleaning schedule process is canceled. [Image showing cancellation of cleaning schedule]

3. Regular Robot Care

To keep robot running at peak performance, perform the following care procedures. If you notice robot picking up less debris from your floor, then empty the bin, clean the filter and rolling brush.

Recommended cleaning/replacement frequency:

3.1 Empty Robot's Bin

1. Press bin release button to remove the bin. [Image showing bin removal]
2. Open bin's door to empty it. [Image showing dust bin being emptied]

3.2 Clean Robot's Filter

1. Remove filter by grasping the white tab. [Image showing filter removal]
2. Shake off debris by tapping the filter against your trash container. [Image showing filter being cleaned]

3.3 Clean Robot's Rolling Brush, Side Brush, Swivel Wheel and Sensors

1. Take out the rolling brush, clean the vacuuming aisle by a cloth. [Image showing rolling brush cleaning]
2. Clean the rolling brush. Cut down the hair winded in the rolling brush with the provided cleaning tool's knife. [Image showing hair being cut from rolling brush]
3. Remove the side brush, use a cloth to remove the dust from the brush. [Image showing side brush cleaning]
4. Pull out the swivel wheel, then clean the swivel wheel with the cleaning tool. [Image showing swivel wheel cleaning]
5. Dust off the cliff sensors to maintain the best performance. [Image showing cliff sensor cleaning]

4. Troubleshooting

Robot will tell you something is wrong with a two-tone distress sound. The indicator will also blink or light red. Refer to the chart as below to resolve the robot's problem. If the problem is not resolved, please contact our COST FREE customer service team for more assistance.

Warm Tips: For some errors, rebooting the robot may resolve the problem. To reboot the robot, press the power button on the bottom on robot, you will hear an audible tone signifying a successful reboot.

5. FAQ

AFTER-SALE SERVICE

Our customer service is friendly and hassle-free, please contact us if you need our help.