R1-1 One-Key RF Remote Controller
Model No.: R1-1
One-key portable dimmer/Wireless remote 30m distance/CR2032 battery/Magnet stuck fix
Features
- Applies to single-color LED controllers.
- Each remote can match one or more receivers.
- Powered by a CR2032 battery.
- Operates with an LED indicator light.
- Features a magnetic back for easy attachment to metal surfaces.
Technical Parameters
| Category | Details |
|---|---|
| Input and Output | Output signal: RF(2.4GHz) Working voltage: 3VDC(CR2032) Working current: <5mA Standby current: < 2μA |
| Warranty & Performance | Standby time: 2 years Remote distance: 30m (Barrier-free space) Warranty: 5 years |
| Safety and EMC | EMC standard (EMC): ETSI EN 301 489-1 V2.2.3, ETSI EN 301 489-17 V3.2.4 Safety standard (LVD): EN 62368-1:2020+A11:2020 Radio Equipment (RED): ETSI EN 300 328 V2.2.2 Certification: CE, EMC, LVD, RED |
| Environment | Operation temperature: Ta: -30°C~+55°C IP rating: IP20 |
Mechanical Structures and Installations
Remote Description
The R1-1 remote controller is a compact, round device featuring a central button with an LED indicator. The back of the remote includes a magnetic holder for easy mounting.
Dimensions: Approximately 43.00 mm in diameter, 17.00 mm in height, with a back holder depth of 26.50 mm.
LED Indicator Function
Click the button to turn the device on/off. Press and hold the button for 1-6 seconds to increase or decrease brightness.
Battery
The remote is powered by a CR2032 battery. Note: Before the first use, please remove the protective film on the battery.
Installation Options
To fix the remote, three options are offered for selection:
- Option 1: Stick on any metal surfaces directly using the magnetic back holder.
- Option 2: Fix it on the wall with two screws (screws not included).
- Option 3: Adhere it to the wall with a paster (paster not included).
Match Remote Control (Two Match Ways)
End users can choose suitable match/delete methods. Two options are offered:
Method 1: Use the Controller's Match Key
Match:
Short press the match key on the controller, then immediately press the on/off key on the remote. The LED indicator will fast flash a few times, indicating a successful match.
Delete:
Press and hold the match key on the controller for 5 seconds to delete all matches. The LED indicator will fast flash a few times, indicating all matched remotes have been deleted.
Method 2: Use Power Restart
Match:
Switch off the power to the receiver, then switch it on again. Immediately short press the on/off key on the remote 3 times. The light blinks 3 times, indicating a successful match.
Delete:
Switch off the power to the receiver, then switch it on again. Immediately short press the on/off key on the remote 5 times. The light blinks 5 times, indicating all matched remotes have been deleted.
Safety Information
- Read all instructions carefully before beginning installation.
- When installing the battery, pay attention to the battery's positive and negative polarity. If the remote will not be used for a long time, remove the battery. When the remote distance becomes smaller and insensitive, replace the battery.
- If there is no response from the receiver, please re-match the remote.
- Handle the remote gently; beware of falling.
- For indoor and dry location use only.
FCC Compliance
FCC Warning
15.19 Labeling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
15.21 Information to user.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF Radiation Exposure Statement:
- This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
- This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 5mm between the radiator and your body.
