LIAN-LI GALAHAD II TRINITY PERFORMANCE 360 INSTALLATION MANUAL
[Lian Li logo]
Hardware List
- A: Thermal Paste (1g) ?
- B: Spatula ?
- C: Thermal Pads ⬜ x2
- D: Screws ? x12
- E: Mounting Brackets ? x2
- F: Backplate ?️ x1
- G: Intel LGA1700/115X/1200 Mounting Bracket ? x1
- H: Intel LGA1700/115X/1200 Mounting Bracket ? x1
- I: Pump Cover Caps ? x4
- J: Pump Cover (Duo-Infinity) ? x1
- K: Pump Cover (Dazzle) ? x1
- L: Pump Cover (Sink Hole) ? x1
- M: ARGB Cable (3-pin) ? x1
- N: ARGB Cable (USB/SATA) ? x1
Installation Guide
Applying Thermal Paste
Step 1: Place the pump assembly onto the CPU. Ensure the control film direction is oriented correctly based on your CPU socket. Refer to the diagram for guidance.
Step 2: Use one thermal pad at a time if needed.
Step 3: The control film direction depends on the CPU. Follow the left reference to place the control film as per different tube orientation.
Visual description: A diagram shows applying thermal paste in a grid pattern on the CPU, then placing the pump over it. Another shows peeling a protective film from the pump block.
Intel LGA1700/115X/1200 Installation
Step 1: Mount the appropriate brackets (G or H) onto the pump assembly.
Step 2: Adjust the position of the pump assembly on the motherboard.
Step 3: Secure the assembly using the provided screws and backplate.
Orientation options:
- Facing downward ⬇️
- Outer way for LGA 1700 ➡️
- Inner way for LGA 115X & 1200 ⬅️
Visual description: Diagrams illustrate attaching brackets, positioning the pump, and securing it with screws for Intel sockets.
Rotating the Pump
The pump head can be rotated 90 degrees ? to adjust the tube orientation.
Note: For performance considerations, only these 2 tube outlet orientations are supported.
Visual description: An arrow shows the pump head rotating 90 degrees.
AMD AM4 Installation
Step 1: Secure the AMD latch onto the platform's retention clip.
Step 2: Tighten with the provided spring nut.
Visual description: Diagrams show how to attach the AMD mounting bracket and secure it.
Mounting in Chassis
Mount the radiator and pump assembly into the PC chassis. Ensure proper placement for airflow and cable management.
Visual description: A diagram shows the radiator and pump assembly being installed into a computer case.
Customizing Pump Cover
You can personalize the pump cover by swapping the decorative caps (J, K, L).
Step 1: Remove the existing pump cover.
Step 2: Peel off the protective film from the new pump cover.
Step 3: Attach the new pump cover securely.
Available covers: Duo-Infinity, Dazzle, Sink Hole.
Visual description: Diagrams show how to detach and attach different pump covers.
Cable Connection Guide
Pump Connection
Warning: ⚠️ Do not connect the wrong type of LED connector. Connecting to a 12V connector will cause permanent damage.
Ensure the convex side of the cable faces downward ⬇️ when connecting.
Visual description: Diagrams show the pump cable connection, highlighting the correct orientation.
Fan Removal and Connection
To remove fans, follow the numbered steps shown in the diagram.
The power adapter cable can connect to either port on the radiator.
Note: A side ARGB kit (P28ARGB-B/P28ARGB-W) is available separately for users who desire additional lighting effects on the fans.
Visual description: Diagrams illustrate fan removal and connection points.
ARGB Device Connection
Connect the ARGB device to one of the following:
- 5V ARGB 3-pin header (for Motherboard sync - non-essential) ?
- USB header (for L-Connect 3 software control) ?
- PSU SATA 15-pin power connector ?
A spare cable is included but not necessary for basic operation.
Visual description: A diagram shows various connection options for ARGB devices.
Fan Speed Control
Control fan speed using the L-Connect 3 software.
Fan Speed Modes:
- L: 200~2300 RPM
- H: 200~3000 RPM
Visual description: A diagram shows a fan speed controller with L and H settings.
