Lutron Caseta Wireless In-wall Dimmer PRO

Welcome to Caseta Wireless In-wall Dimmer PRO

Thank you for purchasing a Caseta Wireless In-wall Dimmer PRO. This device allows you to control your lights from an app or remote by replacing an existing wall switch. Before installation, it is recommended to watch the installation video available at www.casetawireless.com/support. We hope you enjoy the convenience of Caseta Wireless!

Double Your Warranty: Share your feedback and ideas for Caseta Wireless dimmers at www.casetawireless.com/register to extend your warranty by one year.

Contents Supplied

• In-wall Dimmer PRO (PD-10NXD)
• Wire connectors (x5)
• Screws (x2)

Tools You'll Need

• Flat-head screwdriver
• Phillips-head screwdriver
• Pliers

Compatibility

This dimmer works with compatible energy-efficient dimmable light bulbs:

• LED*: up to 250 W
• Incandescent / Halogen: up to 1000 W
• MLV Halogen: up to 1000 VA

Note: You can mix and match dimmable LEDs, as well as halogen and incandescent light bulbs, with Caseta Wireless dimmers. Dimmable LED light bulbs vary in their dimming performance. If you experience flickering or turn-off issues with these bulbs, visit www.casetawireless.com/lowend for information on adjusting the dimmer for optimal bulb performance.

*For a complete list of compatible dimmable LEDs, please visit www.casetawireless.com/bulblist. Compatible light bulbs include models from EcoSmart, Feit, Philips, and Sylvania.

Installing Your Dimmer (Single Pole Installation)

WARNING: SHOCK HAZARD - May result in serious injury or death. Turn off power at circuit breaker or fuse before installing.

1. Turn power off at circuit breaker ⚡: Ensure power is disconnected before proceeding.
2. Remove existing switch from wall: Carefully remove the wallplate and then the existing switch from the wallbox.
3. Remove side sections (if necessary): For some installations, side sections of the dimmer may need to be removed to fit in a multi-gang box. Bend back and forth to remove. Note: Do not remove outside side sections on dimmers at the end of a gang.
4. Disconnect all three wires* from the switch: Carefully detach the wires from the old switch.

Important Note: 3-Way Installation

If more than one switch controls the light (a 3-way installation), you will need to purchase the PJ2-WALL-WH-L01 accessory. For detailed instructions, please visit www.casetawireless.com/3way.

Important Note: Wattage Derating

Removing side sections reduces the dimmer's maximum wattage rating. See the chart below for maximum wattage information (120 V~ 50/60 Hz):

*For maximum wattage information when mixing light bulb types, see www.casetawireless.com/ganging.

5. Connect the dimmer: Follow the wiring diagram.
   • Connect the [Ground Wire] (bare copper or green) from the wallbox to the green wire on the dimmer using a wire connector.
   • Connect the [Load Wire] from the wallbox to the red wire on the dimmer using a wire connector.
   • Connect the [Hot Wire] from the wallbox to the black wire on the dimmer using a wire connector.
   • If available, connect the [Neutral Wire] from the wallbox to the white wire on the dimmer. If neutral is not available, cap the white wire with a wire connector. A neutral wire is required for MLV loads, LED drivers, PHPM-PA, PHPM-3F, and GRX-TVI.
   • Cap the [Blue Wire] with a wire connector. This wire is only used for a 3-way installation with a mechanical toggle switch. See www.casetawireless.com/3way for details.
6. Mount the dimmer: Use the provided screws (x2) to secure the dimmer in the wallbox.
7. Attach the wallplate: Attach the adapter to the dimmer using the provided screws and snap the wallplate on. If installing in a multi-gang box, ensure the wallplate has the correct number of openings for all devices.
8. Turn power on at circuit breaker ⚡: Restore power to the circuit.

Important Information

• CAUTION: Use only with permanently installed fixtures with dimmable LED, halogen, MLV halogen, or incandescent lamps. Do not use to control receptacles or motor-driven appliances to avoid overheating and potential damage.
• Codes: Install in accordance with all national and local electrical codes.
• Grounding: If no grounding means exist in the wallbox, the National Electrical Code (NEC®) allows installation if a nonmetallic faceplate is used or if the circuit is protected by a ground fault circuit interrupter (GFCI). In such cases, cap or remove the green wire before screwing the control into the wallbox.
• FCC/IC Information: This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. Modifications not expressly approved by Lutron Electronics Co., Inc. may void the user's authority to operate this equipment. This equipment generates, uses, and can radiate radio frequency energy and may cause harmful interference to radio communications if not installed and used per instructions.
• Warranty: For warranty information, please visit www.casetawireless.com/warranty.

Using Your Caseta Wireless Kit (Sold Separately)

With a Smartphone or Tablet (Lutron Smart Bridge Required)

The Caseta Wireless dimmer can be controlled via a smartphone when used with the Lutron Smart Bridge. If you are using the dimmer and remote control with the Lutron Smart Bridge, follow the instructions below. For other bridge manufacturers, refer to their specific instructions.

1. Download the Lutron App: Search for "Lutron Caseta" in the Apple App Store or Google Play Store and download the app.
2. Launch the Lutron App: The app will guide you through setting up your devices.
3. Complete Remaining Steps: Use the app to add devices (Pico remotes, Dimmers, Shades), control lights in three ways, schedule your lights, and connect while away.

Without a Smartphone or Tablet (Lutron Smart Bridge Not Required)

Pairing the Dimmer and Pico Remote Control

1. On the dimmer, press and hold the "Off" button until the LEDs start blinking (hold for 6 seconds).
2. On the Pico remote control, press and hold the "Off" button until the lights flash 3 times (hold for 6 seconds).
3. On the Pico remote control, press and hold the "Off" button again until the LEDs on the in-wall dimmer blink twice. The remote is now paired.

Repeat these steps to pair additional Pico remote controls.

Changing the Favorite Light Level on the Pico Remote Control

The round "Favorite" button on the Pico remote control can recall a favorite light level. The default is 50%, but you can change it:

1. On the dimmer, press and hold the "Off" button (hold for 6 seconds until LEDs start blinking).
2. On the Pico remote control, press and hold the "Off" button (hold for 6 seconds until lights flash 3 times).
3. Set the desired light level on the dimmer.
4. On the Pico remote control, press and hold the "Favorite" button (hold for 6 seconds until LEDs blink twice on the in-wall dimmer). The new favorite level is now saved.

Using Your Controls

In-wall Dimmer PRO

• On/Off: Press the top or bottom of the paddle.
• Brighter: Press the upper part of the paddle.
• Darker: Press the lower part of the paddle.
• FASS™ (Front Accessible Service Switch): Pull this switch out to remove power at the light socket for bulb replacement.

Pico Remote Control (Sold Separately)

• On: Press the "On" button.
• Favorite: Press the round "Favorite" button to recall a saved light level.
• Brighter: Press the "Brighter" button.
• Darker: Press the "Darker" button.
• Off: Press the "Off" button.

Replacing Light Bulbs: Pull the FASS™ switch out on the In-wall Dimmer PRO to remove power at the light socket before replacing bulbs.

Important Notes

• For indoor use only.
• Operate between 32°F (0°C) and 104°F (40°C).

Troubleshooting

Go to www.casetawireless.com/support for additional troubleshooting suggestions.

Device Ratings

In-wall Dimmer PRO PD-10NXD: 120 V~ 50/60 Hz

Manufacturer Information

Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.

Lutron, Lutron, Caseta, and Pico are registered trademarks, and FASS™, and Smart Bridge are trademarks of Lutron Electronics Co., Inc. NEC is a registered trademark of the National Fire Protection Association. Google and the Google logo are registered trademarks of Google Inc., used with permission. © 2015 Lutron Electronics Co., Inc.