Vaultek Slider Series NSL2i Smart Safe

Quick Setup Guide

1. Step 1: Remove the Mounting Plate.
2. Step 2: Plug in the safe and install four AAA batteries. This safe requires continuous AC power for normal function. The four AAA batteries provide backup power for approximately 3 months during power outages, ensuring quick access.
3. Step 3: Set up your safe with the Vaultek® ViSN™ smartphone app. Use the app to program your safe, customize settings, and receive live alerts ? for critical safe activity from anywhere.
4. Step 4: Program the Master Code and Biometric Scanner. The ViSN smartphone app will guide you through this process.
5. Step 5: Register the safe. Registration offers benefits such as a three-year warranty, technical support, and easier ordering of replacement keys ? if needed.

Warnings

⚠️ To prevent damage to your Vaultek® unit or injury to yourself or others, read the following safety precautions before using this unit.

• Before use, inspect the safe to ensure the door latches properly. Perform a quick test using the included mechanical key: open and close the safe 5 times. Do not use the product if any problem or defect is noticed. Contact Vaultek customer support at support@vaulteksafe.com.
• Always ensure the safe door is latched when closing. This safe uses a rugged latch system. Press firmly near the center of the front door when closing; it requires a firm press and will lock automatically when closed properly.
• Change the default code as soon as possible to prevent unauthorized access.
• DO NOT lose the keys ?. In the event of a power outage, the four AAA batteries ? will provide power for approximately 3 months.
• DO NOT place or store the backup keys ? inside the safe at any time.
• DO NOT store loaded guns in this unit. Firearms are serious in nature and must be handled with respect. Store responsibly.
• Keep this product away from small children, as the package contains small items that could be a choking hazard.

At a Glance

The Vaultek® Slider Series model NSL2i is a tough, rugged, quick-access, Wi-Fi enabled ? smart safe. Its solid structure and penetration-resistant design make it ideal for quick firearm access. Powered by an AC adapter and backup batteries ?, the safe combines high security with complete access control.

Key Components:

[Diagram: Shows the internal components of the safe. Numbered items are: 1. Biometric Scanner, 2. Backlit Keypad, 3. Backup Key Entry, 4. Mounting Plate, 5. LED Light, 6. Battery Compartment Door, 7. Mounting Plate Release Clip, 8. Program Button.]

Plug-in Required: The safe must be continuously plugged into its AC power adapter for normal function.

Backup Battery Required: Four AAA batteries (not included) are required for backup power and normal function.

Keypad: Features a numeric keypad with a proximity sensor that illuminates when your hand is near.

Biometric Scanner: ViSN Mode supports up to 80 fingerprints; Essential Mode supports up to 20 fingerprints.

Key: Two manual keys ? are provided for access.

Vaultek ViSN: Enables guided programming, safe setting management ⚙️, and live alerts ? via the smartphone app.

Nano Key 3.0 Technology (Sold Separately): Allows quick access via a separate Nano Key device.

Security Sleep Mode: Activates after six consecutive incorrect keypad entries or fingerprint scans. The safe will be unresponsive for four minutes. Further attempts may trigger an alarm. Sleep mode is cleared upon unlocking by an authorized method, including backup keys ?.

How to Remove Safe from the Mounting Plate

To detach the safe from its mounting plate:

1. Open the safe. Locate the release clip on the same side as the attached mounting plate.
2. Simultaneously pull the release clip back using your thumb or finger and lift the safe off the mount. The safe will not detach without pulling the release clip.

[Diagram: Shows the location of the Manual Key Cover, Program Button, and Mounting Slots on the safe.]

Set Up Your Safe with ViSN™

The Vaultek ViSN smartphone app provides step-by-step guidance for programming your safe and accessing advanced features. The web dashboard offers comprehensive control and functionality.

• Program Master Code & Biometric Scanner: Follow in-app instructions.
• Live Alerts: Receive real-time notifications of critical safe activity ?.
• Customize Safe Settings: Adjust interior light brightness, sound levels ⚙️, alert preferences, and more via the ViSN app.

1. Smartphone App: Download the Vaultek ViSN app from Google Play or the Apple Store and follow the on-screen prompts.

Web Dashboard: Visit www.visn.vaulteksafe.com. Note: Safe programming is not available via the ViSN web dashboard.

For assistance, visit vaulteksafe.com/support, select your model for troubleshooting, or email support@vaulteksafe.com.

Power

The Slider Series ViSN safe requires continuous AC power for normal function. Four AAA batteries ? serve as backup power.

In the event of a power outage, the safe switches to Low Power Mode, with backup batteries ? lasting approximately 3 months. The safe will only be online when awake and will be offline in standby mode. Nano Key is not supported during standby.

Plug In Required

1. Connect the safe to power using the included adapter (A).

[Diagram: Shows the AC power adapter labeled 'A'.]

Backup Batteries Required

1. Open the safe. The key entry ? is located at the back.
2. Remove the battery compartment cover by pressing the tab near the right side and sliding the cover out (B).

[Diagram: Shows the battery compartment cover being removed, labeled 'B'.]

3. Install four AAA batteries ? (B). Duracell/Energizer or other reputable brands are recommended for optimal performance.

Programming

Use the Vaultek ViSN smartphone app for guided programming of your safe:

• Master Code Programming
• Biometric Scanner Programming
• Nano Key Programming

1. Smartphone App: Download the Vaultek ViSN app from Google Play or the Apple Store and follow the on-screen prompts.

Essential Mode: If Wi-Fi connectivity via ViSN is not desired, the safe can be set to Essential Mode. This allows programming as a standalone safe (master code, biometric scanner) without Wi-Fi ?. ViSN and Nano Key features are not supported in Essential Mode. Refer to the "Essential Mode Hotkeys" section for more details.

Registration: Register your safe to receive benefits including a three-year warranty, technical support, and easier ordering of replacement keys ?. Visit vaulteksafe.com/support and select your model.

Keypad Hotkeys

Access settings using keypad hotkeys or the Vaultek ViSN app.

• Tamper Detection: Press and hold keys '2' and '4' together. The '3' key will glow RED (tampering detected) or GREEN (no tampering). Reset by opening the safe via an authorized entry point.
• Battery Status: Press and hold the '5' key. Keys '1' through '4' will glow GREEN or RED to indicate battery level ?.
• Sound (ON by Default): Press and hold '1' and '3' together to toggle between sound options: OFF, Low pitch, Medium pitch, and High pitch.
• Factory Reset: With the safe open and the manual key ? turned clockwise, press and hold keys '1', '5', and the Program button until the safe restarts. This erases all programmed information and restores factory defaults, including network configurations. The master code resets to 1-2-3-4-5. Wi-Fi ? configuration will be required again to enable ViSN features.

Essential Mode Hotkeys

Essential Mode settings are accessible via keypad hotkeys only. In ViSN Mode, these settings are available through the smartphone app.

• Safe Mode (ViSN or Essential): By default, the safe is in ViSN Mode. Press and hold the '5' key and the Program button together. If the '1' key turns solid GREEN, the safe is in Essential Mode. If the '2' key turns solid GREEN, it is in ViSN Mode.

ViSN Mode allows Wi-Fi ? connectivity for features not available in Essential Mode, including live alerts ?. Essential Mode operates as a standalone safe without Wi-Fi ? connectivity. Nano Key is not supported in Essential Mode.

Essential Mode Programming: For master code and biometric scanner programming instructions in Essential Mode, visit vaulteksafe.com/support and select your model. Nano Key is not supported.

Essential Mode Hotkeys: For a full list of hotkeys, such as Open Door Alarm, visit vaulteksafe.com/support and select your model, or scan the QR code ? in this manual.

Mounting Plate Overview

Your Vaultek safe can be secured to a vertical surface using the included mounting plate and hardware. Multiple configurations are supported:

• Four-point configuration: For standard vertical surface mounting (1.1).
• Two-point mounting: For installation into a vertical wall stud (1.2).
• Additional base mounts: (1.3).

The mounting plate also features standard VESA 75mm and 100mm fitment for use with other adapter plates (1.4). Hardware for VESA fitment is not included.

[Diagram: Shows the mounting plate with indicators for different mounting configurations: (1.1) Standard four-point configuration for vertical surfaces, (1.2) Two-point configuration suitable for mounting into a wall stud, (1.3) Additional base mounts, and (1.4) indicating VESA 75mm and 100mm fitment compatibility.]

Securing the Mounting Plate

? Tip: Your safe can be installed onto the mounting plate from either the left or right side.

Important: When installing the plate, ensure the bottom is parallel to the floor (E) for horizontal safe opening. Angling the plate or aiming the safe downwards may affect rail mechanics and prevent proper opening.

1. Locate a mounting surface, ensuring sufficient clearance for the safe door to open fully before installing.
2. Position the mounting plate and use a pencil to mark desired hole locations. Drill 7/32" pilot holes.
3. Fasten the mounting plate securely using the provided hardware and tighten firmly.

Visit our mobile-friendly online guide for tutorial videos at vaulteksafe.com/support and select your model.

Attaching the Mounting Plate

To attach the safe to the installed mounting plate:

1. Align the 4 receiving slots on the safe sides with the 4 tabs on the mounting plate.
2. Fully insert the mounting plate tabs into the safe's receiving slots (C/D). Press the safe downwards firmly to lock it in place (E).

[Diagram: Shows the safe being attached to the mounting plate, illustrating the alignment of slots and tabs, and the final locking action.]

FCC Compliance

REV 111224

This device has been evaluated to meet general RF exposure requirements and can be used in portable exposure conditions without restriction.

FCC Statements: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or changes to this equipment. Such modifications could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.