FINPUTSAD RENGÖRA LAGAN RÅGLANDA METOD

Important Safety Information

⚠️ WARNING - The electrical, water, and gas installation and connection must be carried out by a qualified technician according to the manufacturer's instructions and in compliance with the local safety regulations.

Tools Required

• Phillips screwdriver ?
• Flathead screwdriver ?
• 8mm wrench or socket
• Pliers ?️
• Scissors ✂️
• Tape measure ?
• Drill with Ø2mm bit
• Gloves ?

Parts Included

• Part A (e.g., Front panel/door cover) - 1x
• Part B (e.g., Base support) - 1x
• Part C (e.g., Mounting rod/handle) - 1x
• Dowels (D) - 4x
• Screws (E) - 16x
• Screws (F) - 8x
• Hinges (G) - 1x
• Hinges (H) - 1x
• Cam locks (I) - 8x
• Allen key (J) - 2x
• Allen key (K) - 1x
• Screws (L) - 2x
• Screws (M) - 2x
• Mounting brackets (N) - 2x
• Front panel (O) - 2x

Dimensions and Specifications

• Water Pressure: Min 0.05 MPa / 0.5 Bar, Max 1 MPa / 10 Bar
• Minimum clearance for installation: 10mm (side), 400mm (depth), 800mm (height)
• Appliance Height: 820-900 mm
• 60cm Unit Dimensions: Width 598 mm, Depth 555 mm. Requires min 600 mm width, min 560 mm depth.
• 45cm Unit Dimensions: Width 448 mm, Depth 555 mm. Requires min 450 mm width, min 560 mm depth.
• Water inlet/outlet hose length: ~1300mm / ~1500mm
• Drainage pipe length: ~1500mm
• Minimum ventilation hole diameter: Ø 25 mm

Installation Steps

1. Step 1: Prepare Cabinet Top

   Attach sealing strip to the top edge of the cabinet. Ensure it is correctly positioned.

2. Step 2: Attach Rod

   Attach the rod (C) to the top of the dishwasher unit.

3. Step 3: Insert Dishwasher

   Carefully slide the dishwasher unit into the prepared cabinet opening.

4. Step 4: Secure Dishwasher

   Secure the dishwasher to the cabinet using screws (2x) and cam locks (I). Ensure the unit is level.

5. Step 5: Attach Front Panels

   Attach the front panels (O) to the dishwasher door. This may involve using specific accessories like VÅGLIG. Ensure panels are aligned correctly. Maximum panel height is 800mm.

   Use screws (8x) to fix the panels.

6. Step 6: Install Hinges and Brackets

   Attach hinges (G, H) and mounting brackets (N) to the dishwasher door and cabinet using screws (16x, 2x, 2x).

7. Step 7: Drill Mounting Holes

   Drill 24 holes of Ø2mm at specified locations on the cabinet and door for mounting and adjustments.

8. Step 8: Connect Hinges to Door

   Connect the main hinge components (D, E, F) to the door panel and the cabinet frame, using the provided screws and cam locks.

9. Step 9: Attach Handles

   Attach handles or knobs (G, I) to the front panel using screws.

10. Step 10: Adjust Door Alignment

    Adjust the door alignment using the screws on the hinges. Ensure a gap of no more than 2mm between the door and the cabinet.

11. Step 11: Secure Appliance to Cabinet

    Secure the dishwasher unit to the cabinet using screws and brackets.

12. Step 12: Attach Front Panel

    Attach the front panel to the appliance using the hinges and securing mechanisms (2x).

13. Step 13: Lock Front Panel

    Engage the locking mechanism to secure the front panel.

14. Step 14: Fine-tune Door Alignment

    Adjust the door height and alignment by turning the adjustment screws (K) up to 360 degrees. Ensure the door opens and closes smoothly.

15. Step 15: Final Checks

    Perform final checks on all connections and ensure the appliance is stable and level. Slide the door into its final position.

    ⚠️ Do not use excessive force or incorrect tools during installation.

    ⚠️ Ensure proper ventilation.

    ⚠️ Check electrical and water connections are secure.