ZS01 Keypad Digital Deadbolt

Installation Overview

Read this manual carefully before installing and operating!

Steps:

• STEP 1: Prepare the door and check dimensions (P 3)
• STEP 2: Install the latch and strike (P 4)
• STEP 3: Install exterior assembly (P 6)
• STEP 4: Install interior assembly (P 7)
• STEP 5: Detect left/right hand door installation (P 8)

Parts List

• A Backup Key x2 ?
• B Exterior Assembly x1 ?
• C Latch x1 ⚙️
• D Strike x1 ?
• D-1 Reinforcement Plate x1 (optional)
• E Mounting Plate x1 ?
• F Interior Assembly x1 ?
• G Battery Cover x1 ?
• H Strike Screws x2 ?
• I Latch Screws x2 ?
• J Mounting plate Screws x2 ?
• K Interior Assembly Screws x3 ?
• L Reset Tool x1 ?️
• M Drive-In Collar (Optional) ⚙️

If any parts are missing or damaged, please contact Customer Support.

Installation Steps

STEP 1: Prepare the door and check dimensions

A. Door Hole Measurement: Measure to confirm that the hole in the door is 2-1/8" (54 mm). Measure to confirm that the hole in the door edge is 1" (25 mm).

B. Backset Measurement: Measure to confirm that the backset is either 2-3/8" or 2-3/4" (60 or 70 mm).

C. Door Thickness Measurement: Measure to confirm that the door is 1-3/8" to 2" (35 mm or 50 mm) thick.

D. Door Frame Hole Depth: Make sure the hole in the door frame is drilled a minimum of 1" (25 mm) deep.

STEP 2: Install the latch and strike

A. Determine backset and adjust the latch: Hold the latch in front of the door hole, with the latch face flush against the door edge. Check if the slotted hole is centered in the door hole.

• If YES: No adjustment is required. Proceed to the next step.
• If NO: The slotted hole is NOT centered. Rotate and pull the latch as shown to extend the latch.

B. Install the latch: For a chiseled door edge, install the latch directly. For a not chiseled door edge, use the drive-in collar (M) with the latch.

C. Test deadbolt: Use a screwdriver to test if the deadbolt works smoothly.

D. Install strike on the door frame: Ensure the hole in the door frame is drilled a minimum of 1" (25 mm) deep. Install the strike plate (D) and optional reinforcement plate (D-1).

STEP 3: Install exterior assembly

IMPORTANT: Before installation, make sure the latch is fully retracted (in the unlocked position).

A. Mount exterior assembly: With the latch fully retracted, route the cable below the latch and insert the torque blade through the slot in the latch.

B. Secure mounting plate: Keep the mounting plate parallel to the door edge. Secure the mounting plate with the supplied mounting plate screws (J). Do not overtighten screws.

STEP 4: Install interior assembly

A. Battery Cover: Push the battery cover out in the direction illustrated.

B. Cable Connector: Insert the cable connector to the socket. Push the connector in firmly until it is completely attached.

C. Install interior assembly: Keep the thumb turn in the vertical position and install the interior assembly.

D. Secure interior assembly: Attach the interior assembly to the mounting plate and tighten 3 interior assembly screws (K).

STEP 5: Detect left/right hand door installation

IMPORTANT: This step is required and crucial for the lock to operate properly.

A. Load Batteries: While the door is OPEN and UNLOCKED, load 3 AA batteries into the battery compartment. Note: For long life, please use all new, non-rechargeable Alkaline batteries only.

B. Reset Lock: Press and hold the Reset button on the interior assembly using the reset tool.

C. Learn Door Orientation: Load the 4th battery and keep holding the reset button for 3 seconds, until you hear the sound of "beep" ?. The latch bolt will extend to learn the orientation of the door automatically.

Programming Instructions

At a Glance

Exterior Assembly: Features a Keypad ?, Light Indicator ?, and Keyhole ?.

Interior Assembly: Includes Battery Cover ?, Reset Button (RES) ?, and Thumb Turn ?.

How to Use

UNLOCK the door from outside: Enter Master/User code + #, then press 1. Alternatively, use the backup key ?.

LOCK the door from outside: Press any key on the keypad for 2 seconds.

• Auto Lock Mode: The bolt will extend out automatically in 30 seconds after unlocking.
• Manual Mode: Press any key on keypad for 2 seconds.

UNLOCK the door from inside: Rotate the thumb turn to the Unlock position.

LOCK the door from inside: Rotate the thumb turn to the Lock Position.

• Auto Lock Mode: The device will be locked automatically.
• Manual Mode: Rotate the thumb turn to Lock Position.

Definitions

• Master Code: Required for programming and feature settings. Can be used to unlock the door under vacation mode. The default master code needs to be changed before programming. Property owner & manager should keep this information confidential.
• Auto Lock: Automatically locks the deadbolt 30 seconds after unlocking. This feature is off by default. You can customize the Auto Lock time delay between 10 and 99 seconds.
• Key Unlock: Always available when batteries are completely dead or valid User Codes are forgotten.
• Low Battery Indicator: 10 beeps along with 10 red light flashing after pressing any key to lock or unlock the door indicates a need to replace batteries. Replace with 4 brand new AA alkaline batteries and do not mix used and new batteries. All settings are stored in the lock while batteries are removed and replaced.
• Wrong Entry Limit: After 10 unsuccessful attempts at entering an invalid PIN code, the unit will shut down for 3 minutes.
• Silent Mode: Beep sounds when pressing keypad can be muted. Low battery and system alerts will still be heard.
• Vacation Mode: A security feature for when leaving home for vacation or long trip. Enabling vacation mode restricts all user codes until the master code is entered. If the lock is unlocked by the thumb turn from inside, an alarm will sound.
• One Time User Code: This code can be used only once and is automatically deleted after use.
• Unlock with Fake code: Prevents PIN code exposure by entering random digits before or after the PIN code. Example: 83618 137192 14710 (password with random digits).

Code Format

1. Master Code: 4 to 10 digits. The default Master Code is 12345678. It is required that you change it to your own code before programming.
2. User Code: 20 User Codes (4-10 digits), 1 one-time User Code can be programmed and stored.
3. Disallowed Combinations: Master Code and User Code do not support the following:
   • Forward number sequence (e.g., 1 2 3 4 5 6 7 8 9) ❌
   • Backward number sequence (e.g., 9 8 7 6 5 4 3 2 1) ❌
   • Repeat number sequence (e.g., 2 2 2 2 2 2 2 2 2) ❌
   • Containing existing code sequence (e.g., if 5683 is a code, then 568391 is disallowed) ❌

Quick Set Up

Change Master Code: * + Master Code + # → Press 1 → Wait for green light flash → New Master Code + # → Wait for green light flash → Succeed (Green light flash)

Add User Code: * + Master Code + # → Press 2 → Wait for green light flash → New User Code + # → Wait for green light flash → Succeed (Green light flash)

Delete User Code: * + Master Code + # → Press 3 → Wait for green light flash → Unwanted User Code + # → Succeed (Green light flash)

Silent Mode: * + Master Code + # → Press 4 → Wait for green light flash → 1 + # (Silent Mode Disabled, Green light flash) OR 2 + # (Silent Mode Enabled, Green light flash)

Auto Lock: * + Master Code + # → Press 5 → Wait for green light flash → 1 + # (Auto Lock Enabled, Green light flash) OR 2 + # (Auto Lock Disabled, Green light flash)

Set Auto Lock Time: * + Master Code + # → Press 8 → Wait for green light flash → Enter New Duration Time (10-99s) + # → Succeed (Green light flash)

Add One-Time Code: * + Master Code + # → Press 7 → Wait for green light flash → New User Code + # → Wait for green light flash → Succeed (Green light flash)

Enable Vacation Mode: * + Master Code + # → Press 6 → Wait for green light flash → Press # → Vacation Mode Enabled (Green light flash)

Disable Vacation Mode: Master Code + # → Vacation Mode Disabled (The door was opened)

Notes:

1. Beeps only sound when the Silent Mode is disabled.
2. If the indicators flash red light, it means your setting failed and you will need to re-enter the master mode to continue programming.

Factory Default Settings

How to Reset?

IMPORTANT: The resetting will delete all User Codes stored in the lock.

1. Keep the door open and unlocked.
2. Press and hold the Reset button (RES) ?, at the same time take out one battery ? and then place it back.
3. Keep holding the Reset button for 3 seconds, until you hear the sound of "beep" ? and the latch will extend automatically.

Troubleshooting

Why does not the latch extend but the motor is rotating when resetting my lock?

Improper installation may have caused the issue. Please follow the steps to review:

1. Please make sure the latch and strike are aligned.
2. Please slightly loosen the mounting screws on the external assembly keypad and the latch bolt if the screws are overtightened.
3. Please open your door and reset the lock.

Why does not the latch extend and the motor isn't rotating when resetting my lock?

The deadbolt latch should be retracted (unlocked) through all your installation process. The thumb turn should be vertical in your installation steps 4C and 5A. Please open your door and reset the lock.

When I attempt to lock/unlock my deadbolt, why does the latch go in and out for a few times?

It happens when the latch and strike are misaligned. Please make sure the bolt hole on the door frame is at least 1 inch deep, so that the bolt can be fully extended. Please check if the door can be closed properly; the deadbolt should not impact the strike or door frame on the door frame side, it should go directly into the hole properly.

Why does my lock only work properly when the backup key is in? Why am I unable to pull the key out in the unlocked position?

You may need to re-install the whole lock. Please make sure when you start to install, the lock is in unlocked status. Please make sure the thumb turn is vertical. Please do not put the backup key in the lock during the installation.

What does 5 short and fast beeps mean while programming?

It alerts you either time-out or wrong entry. Please be sure to complete each setting step within 5 seconds. Please change the default master code in the first time programming. Please be sure the user code is with correct format and with 4 to 10 digits.

What if I forget my Master Codes?

If you forget your Master code, resetting your lock will revert to the original master code (12345678), and all previous user codes will be erased.

Information & Safety Warnings

• Protect your User Codes and Master Code.
• Restrict access to your lock's interior assembly and routinely check your settings to ensure they have not been altered without your knowledge.
• Do not use an electric screwdriver during installation.
• This manufacturer advises that no lock can provide complete security by itself.
• This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property.
• No lock can substitute for caution, awareness of your environment, and common sense.
• Care should be taken to ensure a long-lasting finish. When cleaning is required, use a soft, damp cloth. Using lacquer thinner, caustic soaps, abrasive cleaners, or polishes could damage the coating and result in tarnishing.
• The lock is water resistant. It can withstand water splashes; however, do not let water and liquids get into the lock.
• Avoid exposure to direct sunlight. Long-term exposure to direct sunlight may damage the lock.