Thank you for purchasing our products. Please review this manual thoroughly before operating your device. All pictures in this manual are for illustration purpose only. Actual product may vary due to product upgrade.
Installation Overview
Read this manual carefully before installing and operating!
STEP 1: Prepare the door and check dimensions
A. Door Hole Measurement: Measure to confirm that the hole in the door is 2-1/8" (54mm).
B. Door Edge Hole Measurement: Measure to confirm that the hole in the door edge is 1" (25mm).
C. Backset Measurement: Measure to confirm that the backset is either 2-3/8" or 2-3/4" (60mm or 70mm).
D. Door Thickness Measurement: Measure to confirm that the door is 1-3/8" to 2" (35mm to 50mm) thick.
E. Door Frame Hole Depth: Make sure the hole in the door frame is drilled a minimum of 1" (25mm) deep.
STEP 2: Install the latch and strike
A. Determine backset and adjust the latch:
Hold the latch in front of the door hole, with the latch face flush against the door edge. Is the slotted hole centered in the door hole?
- YES: No adjustment is required. Proceed to next step.
- NO: Slotted hole is NOT centered. Rotate and pull the latch as shown to extend latch. The latch can be adjusted for 2-3/8" (60mm) or 2-3/4" (70mm) backsets.
B. Install the latch:
For doors with a chiseled edge, install the latch directly. For doors without a chiseled edge, use the Drive-In Collar (M) if necessary.
Secure the latch using Latch Screws (I).
C. Test Deadbolt: Use a screwdriver to test if the deadbolt works smoothly.
D. Install strike on the door frame: Make sure the hole in the door frame is drilled a minimum of 1" (25mm) deep. Secure the strike using Strike Screws (H). The Reinforcement Plate (D-1) is optional.
STEP 3: Install exterior assembly
Before installation, make sure the latch is fully retracted (in the unlocked position).
A. Route Cable and Insert Torque Blade: With the latch fully retracted (unlocked position), route the cable below the latch, and insert the torque blade through the slot in the latch. Keep parallel to door edge.
B. Secure Mounting Plate: Secure the mounting plate with the supplied Mounting plate Screws (J). Do not overtighten screws.
STEP 4: Install interior assembly
A. Prepare Battery Cover: Push the battery cover out in the direction as illustrated.
Do not load batteries until lock is completely installed.
B. Connect Cable: Insert the cable connector to the socket. Push the connector in firmly until it is completely attached.
C. Install Interior Assembly: Keep the thumb turn in vertical position and install the interior assembly.
D. Attach Interior Assembly: Attach Interior Assembly to Mounting Plate and tighten 3 Interior Assembly Screws (K).
STEP 5: Detect left/right hand door installation
This step is required and crucial for the lock to operate properly.
A. Load Batteries: While the door is OPEN and UNLOCKED, load 3 AA batteries into the battery compartment. Note: For long last, please use all new, non-rechargeable Alkaline batteries only.
B. Press Reset Button: Press and hold the Reset button (RES) on the interior assembly by using the reset tool.
C. Complete Reset: Load the 4th battery and keep holding the reset button for 3 seconds, until you hear the sound of "beep". The latch bolt will extend to learn the orientation of the door automatically.
Programming Instructions
At a Glance
Exterior Assembly: Features a Multi-Function Button (MFB), Keypad, and Keyhole.
Interior Assembly: Features a Battery Cover, Reset Button (RES), and Thumb Turn.
How to Use
Unlock the door from outside
Enter Master/User code, then press #.
Lock the door from outside
- Auto Lock Mode: The bolt will extend out automatically in 30 seconds after unlocking.
- Manual Mode: Press any key on the keypad for 2 seconds.
Unlock the door from inside
Rotate the thumb turn to the Unlock position.
Lock the door from inside
- Auto Lock Mode: The device will be locked automatically.
- Manual Mode: Rotate the thumb turn to the Lock Position.
Definitions
- Master Code: Required for programming and feature settings. Can be used to unlock the door under vacation mode. The default master code must be changed before programming. Keep this information confidential.
- Auto Lock: Automatically locks the deadbolt 30 seconds after unlocking (feature is off by default). Customizable delay between 10 and 99 seconds.
- Key Unlock: Always available when batteries are dead or User Codes are forgotten.
- Low Battery Indicator: 10 beeps along with 10 red light flashes indicate it's time to replace batteries. Use 4 brand new AA alkaline batteries; do not mix used and new batteries. Settings are stored when batteries are removed and replaced.
- Wrong Entry Limit: After 10 unsuccessful attempts at entering an invalid PIN code, the unit shuts down for 3 minutes.
- Silent Mode: Mutes beep sounds when pressing the keypad, but low battery and system alerts are still audible.
- Vacation Mode: Security feature for when away. Restricts all user codes until the master code is entered. Unlocking via thumb turn from inside triggers an alarm.
- One Time User Code: Can be used only once and is automatically deleted afterward.
- Unlock with Fake code: Prevents PIN code exposure by entering random digits before or after the actual PIN code. Example:
[random digits] 137192 [random digits]
Code Format
- Master Code: 4 to 10 digits. The default Master Code is 12345678. It is required that you change it to a code of your own before programming.
- User Code: 20 User Codes (4-10 digits), 1 one-time User Code can be programmed and stored.
- Both Master Code and User Code do not support the following combinations:
- Forward number sequence (e.g., 123456789) ✖
- Backward number sequence (e.g., 987654321) ✖
- Repeat number sequence (e.g., 222222222) ✖
- Containing existing code sequence (e.g., if '5683' is used, '568391' is not allowed) ✖
Quick Set Up
Important: The default Master Code is 12345678. It is required that you change it to a code of your own before programming.
Change Master Code:
Press ≡ + Master Code + ≡ → Wait for long green lights → Press 1 → Wait for green light flash → New Master Code + ≡ → Wait for green light flash → New Master Code + ≡ → Wait for green light flash → Succeed (Green light flash).
Add User Code:
Press ≡ + Master Code + ≡ → Wait for long green lights → Press 2 → Wait for green light flash → New User Code + ≡ → Wait for green light flash → Succeed (Green light flash).
Delete User Code:
Press ≡ + Master Code + ≡ → Wait for long green lights → Press 3 → Wait for green light flash → Unwanted User Code + ≡ → Wait for green light flash → Succeed (Green light flash).
Silent Mode:
Press ≡ + Master Code + ≡ → Wait for long green lights → Press 4 → Wait for green light flash → 1 + ≡ → Silent Mode Disabled (Green light flash) OR 2 + ≡ → Silent Mode Enabled (Green light flash).
Auto Lock:
Press ≡ + Master Code + ≡ → Wait for long green lights → Press 5 → Wait for green light flash → 1 + ≡ → Auto Lock Enabled (Green light flash) OR 2 + ≡ → Auto Lock Disabled (Green light flash).
Set Auto Lock Time:
Press ≡ + Master Code + ≡ → Wait for long green lights → Press 8 → Wait for green light flash → Enter New Duration Time (10-99s) + ≡ → Succeed (Green light flash).
Add One-Time Code:
Press ≡ + Master Code + ≡ → Wait for long green lights → Press 7 → Wait for green light flash → New User Code + ≡ → Wait for green light flash → Succeed (Green light flash).
Enable Vacation Mode:
Press ≡ + Master Code + ≡ → Wait for long green lights → Press 6 → Wait for green light flash → Vacation Mode Enabled (Green light flash).
Disable Vacation Mode:
Master Code + ≡ → Vacation Mode Disabled (The door was opened).
Notes:
- Beeps only sound when the Silent Mode is disabled.
- If the indicators flash red light, it means your setting failed and it will require to re-enter master mode to continue programming.
Factory Default Settings
How to Reset?
The resetting will delete all User Codes stored in the lock.
- Keep the door open and unlocked.
- Press and hold the Reset button (RES), at the same time take out one battery and then place it back.
- Keep holding the Reset button for 3 seconds, until you hear the sound of "beep" and the latch will extend automatically.
| Settings | Factory Default |
|---|
| Master Code | 12345678 |
| Auto Lock | Disabled |
| Silent Mode | Disabled |
| Wrong Code Entry Limit | 10 times |
| Shutdown Time | 3 mins |
| Vacation Mode | Disabled |
Troubleshooting
Why does not the latch extend but the motor is rotating when resetting my lock?
Improper installation may have caused the issue. Please follow the steps to review:
- Please make sure the latch and strike are aligned.
- Please slightly loosen the mounting screws on the external assembly keypad and the latch bolt if the screws are over-tightened.
- Please open your door and reset the lock.
Why does not the latch extend and the motor isn't rotating when resetting my lock?
The deadbolt latch should be retracted (unlocked) through all your installation process. The thumb turn should be vertical in your installation steps 4C and 5A. Please open your door and reset the lock.
When I attempt to lock/unlock my deadbolt, why does the latch go in and out for a few times?
It happens when the latch and strike are misaligned. Please make sure the bolt hole on the door frame is at least 1 inch deep, so that the bolt can be fully extended. Please check if the door can be closed properly; the deadbolt should not impact the strike or door frame on the door frame side, it should go directly into the hole properly.
Why does my lock only work properly when the backup key is in? Why am I unable to pull the key out in the unlocked position?
You may need to re-install the whole lock. Please make sure when you start to install, the lock is in unlocked status; please make sure the thumb turn is vertical. Please do not put the backup key in the lock during the installation.
What does 5 short and fast beeps mean while programming?
It alerts you either time-out or wrong entry. Please be sure to complete each setting step within 5 seconds. Please change the default master code in the first time programming. Please be sure the user code is with correct format and with 4 to 10 digits.
What if I forget my Master Codes?
If you forget your Master code, resetting your lock will revert to the original master code (12345678), and all previous user codes will be erased.
