KS01 Keypad Digital Deadbolt

Thank you for purchasing our products. Please review this manual thoroughly before operating your device. All pictures in this manual are for illustration purpose only. Actual product may vary due to product upgrade.

Installation Overview

⚠️Read this manual carefully before installing and operating!

Installation Steps:

• STEP 1: Prepare the door and check dimensions (Page 3)
• STEP 2: Install the latch and strike (Page 4)
• STEP 3: Install exterior assembly (Page 6)
• STEP 4: Install interior assembly (Page 7)
• STEP 5: Detect left/right hand door installation (Page 8)

Programming Instructions:

• At a Glance (Page 9)
• How to Use (Page 10)
• Definitions (Page 11)
• Code Format (Page 12)
• Quick Set Up (Page 13)
• Factory Default Settings (Page 15)
• Troubleshooting (Page 16)

? TOOL REQUIRED:

❌ Do not use an electric screwdriver during installation.

❗ IMPORTANT:

Do not load batteries until lock is completely installed.

STEP 1: Prepare the door and check dimensions

A. Measure Door Holes:

• Confirm the hole in the door is 2-1/8" (54mm).
• Confirm the hole in the door edge is 1" (25mm).

B. Measure Backset:

• Confirm the backset is either 2-3/8" (60mm) or 2-3/4" (70mm).

C. Measure Door Thickness:

• Confirm the door thickness is 1-3/8" to 2" (35mm to 50mm).

D. Check Door Frame Hole:

• Make sure the hole in the door frame is drilled a minimum of 1" (25mm) deep.

STEP 2: Install the latch and strike

A. Determine backset and adjust the latch:

Hold the latch in front of the door hole, with the latch face flush against the door edge. Is the slotted hole centered in the door hole?

• YES: No adjustment is required. Proceed to next step.
• NO: Slotted hole is NOT centered. Rotate and pull the latch as shown to extend latch.

B. Install the latch:

• For chiseled doors: Insert latch, secure with 2 Latch Screws (I).
• For non-chiseled doors: Insert latch and Drive-In Collar (M), secure with 2 Latch Screws (I).

C. Test deadbolt:

Use a screwdriver to test if the deadbolt works smoothly.

D. Install strike on the door frame:

❗ IMPORTANT: Make sure the hole in the door frame is drilled a minimum of 1" (25mm) deep.

Install the Strike (D) and Reinforcement plate (D-1, optional) using Strike Screws (H).

STEP 3: Install exterior assembly

❗ IMPORTANT: Before installation, make sure the latch is fully retracted (in the unlocked position).

A. Route cable and insert torque blade:

With the latch fully retracted (in the unlocked position), route the cable below the latch, and insert the torque blade through the slot in the latch.

B. Secure mounting plate:

Keep parallel to door edge. Secure the mounting plate with the supplied Mounting plate Screws (J). Do not overtighten screws.

STEP 4: Install interior assembly

A. Prepare battery cover:

Push the battery cover out in the direction as illustrated.

❗ IMPORTANT: Do not load batteries until lock is completely installed.

B. Connect cable:

Insert the cable connector to the socket. Push the connector in firmly until it is completely attached.

C. Install interior assembly:

Keep the thumb turn in vertical position and install the interior assembly.

D. Attach interior assembly:

Attach Interior Assembly to Mounting Plate and tighten 3 Interior Assembly Screws (K).

STEP 5: Detect left/right hand door installation

❗ IMPORTANT: Reset the lock to teach the lock the orientation of the door. This step is required and crucial for the lock to operate properly.

A. Load batteries:

While the door is OPEN and UNLOCKED, load 3 AA batteries into the battery compartment. Note: For long last, please use all new, non-rechargeable Alkaline batteries only.

B. Press reset button:

Press and hold the Reset button on the interior assembly by using the reset tool.

C. Load 4th battery and finalize:

Load the 4th battery and keep holding the reset button for 3 seconds, until you hear the sound of "beep". The latch bolt will extend to learn the orientation of the door automatically.

Programming Instructions

At a Glance

Exterior Assembly: Features a keypad, Multi-Function Button (MFB), and Keyhole.

Interior Assembly: Features a Battery Cover, Reset Button, and Thumb Turn.

How to Use

UNLOCK the door from outside:

1. Enter Master/User code
2. Press #

LOCK the door from outside:

• Auto Lock Mode: The bolt will extend out automatically in 30 seconds after unlocking.
• Manual Mode: Press any key on keypad for 2 seconds.

UNLOCK the door from inside:

Rotate the thumb turn to Unlock position.

LOCK the door from inside:

• Auto Lock Mode: The device will be locked automatically.
• Manual Mode: Rotate the thumb turn to Lock Position.

Definitions

• Master Code: Required for programming and feature settings. Can be used to unlock the door under vacation mode. The default master code needs to be changed before programming. Property owner & manager should keep this information confidential.
• Auto Lock: Automatically locks the deadbolt 30 seconds after unlocking. This feature is off by default. You can customize the Auto Lock time delay between 10 and 99 seconds.
• Key Unlock: Key Unlock is always available when the batteries are completely dead or valid User Codes are forgotten.
• Low Battery Indicator: If you hear 10 beeps along with 10 red light flashing after pressing any key to lock or unlock the door, it's an alert for replacing batteries. Please replace with 4 brand new AA alkaline batteries and do not mix used and new batteries. All settings are stored in the lock while the batteries are removed and replaced.
• Wrong Entry Limit: After 10 unsuccessful attempts at entering an invalid PIN code, the unit will shut down for 3 minutes.
• Silent Mode: The beep sounds when pressing the keypad can be muted. You will still hear low battery and system alerts.
• Vacation Mode: A security feature for when you are leaving your home for vacation or a long trip. Enabling vacation mode will restrict all user codes until the master code is entered on the keypad. If the lock is unlocked by the thumb turn from the inside, the lock will sound an alarm.
• One Time User Code: This code can only be used once and will be automatically deleted after use.
• Unlock with Fake code: User can prevent PIN code exposure from strangers by entering random digits before or after the PIN code. (Example: 83618 [password] 14710)

Code Format

1. Master Code: 4 to 10 digits. The default Master Code is 12345678. It is required that you change it to a code of your own before programming.
2. User Code: 20 User Codes (4-10 digits), 1 one-time User Code can be programmed and stored in the lock.
3. Unsupported Combinations: Both Master Code and User Code do not support the following combinations of numbers:
   • Forward number sequence (e.g., 123456789) ❌
   • Backward number sequence (e.g., 987654321) ❌
   • Repeat number sequence (e.g., 22222222) ❌
   • Containing existing code sequence (e.g., if 5683 is an existing code, 568391 is not allowed) ❌

Quick Set Up

Change Master Code: Press [MFB] + Master Code + [MFB] → Wait for long green lights → Press 1 → Wait for green light flash → New Master Code + [MFB] → Wait for green light flash → Succeed (Green light flash).

Add User Code: Press [MFB] + Master Code + [MFB] → Wait for long green lights → Press 2 → Wait for green light flash → New User Code + [MFB] → Wait for green light flash → Succeed (Green light flash).

Delete User Code: Press [MFB] + Master Code + [MFB] → Wait for long green lights → Press 3 → Wait for green light flash → Unwanted User Code + [MFB] → Succeed (Green light flash).

Silent Mode: Press [MFB] + Master Code + [MFB] → Wait for long green lights → Press 4 → Wait for green light flash → 1 + [MFB] (Silent Mode Disabled, Green light flash) OR 2 + [MFB] (Silent Mode Enabled, Green light flash).

Auto Lock: Press [MFB] + Master Code + [MFB] → Wait for long green lights → Press 5 → Wait for green light flash → 1 + [MFB] (Auto Lock Enabled, Green light flash) OR 2 + [MFB] (Auto Lock Disabled, Green light flash).

Set Auto Lock Time: Press [MFB] + Master Code + [MFB] → Wait for long green lights → Press 8 → Wait for green light flash → Enter New Duration Time (10-99s) + [MFB] → Succeed (Green light flash).

Add One-Time Code: Press [MFB] + Master Code + [MFB] → Wait for long green lights → Press 7 → Wait for green light flash → New User Code + [MFB] → Wait for green light flash → Succeed (Green light flash).

Enable Vacation mode: Press [MFB] + Master Code + [MFB] → Wait for long green lights → Press 6 → Wait for green light flash → Vacation Mode Enabled (Green light flash).

Disable Vacation mode: Master Code + [MFB] → Vacation Mode Disabled (Green light flash). The door was opened.

Notes:

• Beeps only sound when the Silent Mode is disabled.
• If the indicators flash red light, it means your setting failed and it will require to re-enter master mode if you would like to continue your programming.

Factory Default Settings

How to Reset?

❗ IMPORTANT: The resetting will delete all User Codes stored in the lock.

1. Keep the door open and unlocked.
2. Press and hold the Reset button, at the same time take out one battery and then place it back.
3. Keep holding the Reset button for 3 seconds, until you hear the sound of "beep" and the latch will extend automatically.

Troubleshooting

• Why does not the latch extend but the motor is rotating when resetting my lock?
  Improper installation may have caused the issue. Please follow the steps to review:
  1. Please make sure the latch and strike are aligned.
  2. Please slightly loosen the mounting screws on the external assembly keypad and the latch bolt if the screws are over-tightened.
  3. Please open your door and reset the lock.
• Why does not the latch extend and the motor isn't rotating when resetting my lock?
  The deadbolt latch should be retracted(unlocked) through all your installation process.
  The thumb turn should be vertical in your installation steps 4C and 5A.
  Please open your door and reset the lock.
• When I attempt to lock/unlock my deadbolt, why does the latch go in and out for a few times?
  It happens when the latch and strike are misaligned.
  Please make sure the bolt hole on the door frame is at least 1 inch deep, so that the bolt can be fully extended.
  Please check if the door can be closed properly, the deadbolt should not impact the strike or door frame on the door frame side, it should go directly into the hole properly.
• Why does my lock only work properly when the backup key is in? Why am I unable to pull the key out in the unlocked position?
  You may need to re-install the whole lock.
  Please make sure when you start to install, the lock is in unlocked status; Please make sure the thumb turn is vertical. Please do not put the backup key in the lock during the installation.
• What does 5 short and fast beeps mean while programming?
  It alerts you either time-out or wrong entry.
  Please be sure to complete each setting step within 5 seconds.
  Please change the default master code in the first time programming.
  Please be sure the user code is with correct format and with 4 to 10 digits.
• What if I forget my Master Codes?
  If you forget your Master code, resetting your lock will revert to the original master code (12345678), and all previous user codes will be erased.

Information & Safety Warnings

• Protect your User Codes and Master Code.
• Restrict access to your lock's interior assembly and routinely check your settings to ensure they have not been altered without your knowledge.
• Do not use an electric screwdriver during installation.
• This manufacturer advises that no lock can provide complete security by itself.
• This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property.
• No lock can substitute for caution, awareness of your environment, and common sense.
• Care & Cleaning: Care should be taken to ensure a long-lasting finish. When cleaning is required, use a soft, damp cloth. Using lacquer thinner, caustic soaps, abrasive cleaners, or polishes could damage the coating and result in tarnishing.
• Water Resistance: The lock is water resistant. It can withstand water splashes; however, do not let water and liquids get into the lock.
• Sunlight Exposure: Avoid exposure to direct sunlight. Long-term exposure to direct sunlight may damage the lock.