Keypad Digital Deadbolt

Steps:

• STEP 1: Prepare the door and check dimensions (Page 3)
• STEP 2: Install the latch and strike (Page 4)
• STEP 3: Install exterior assembly (Page 6)
• STEP 4: Install interior assembly (Page 7)
• STEP 5: Detect left/right hand door installation (Page 8)

Tool Required:

Do not use an electric screwdriver during installation. ?

Important:

Do not load batteries until lock is completely installed. ⚠️

STEP 1: Prepare the door and check dimensions

A Measure to confirm that the hole in the door is 2-1/8" (54mm). Measure to confirm that the hole in the door edge is 1" (25mm).

B Measure to confirm that the backset is either 2-3/8" or 2-3/4" (60 or 70mm).

C Measure to confirm that the door is 1-3/8" to 2" (35mm or 50mm) thick.

D Make sure the hole in the door frame is drilled a minimum of 1" (25mm) deep.

STEP 2: Install the latch and strike

A: Determine backset and adjust the latch

Hold the latch in front of the door hole, with the latch face flush against the door edge. Is the slotted hole centered in the door hole?

• YES: No adjustment is required. Proceed to next step. ✔️
• NO: Slotted hole is NOT centered. Rotate and pull the latch as shown to extend latch.

B: Install the latch

For chiseled doors, follow steps 1-4. For not chiseled doors, follow steps 1-4.

(Diagram shows latch installation with screws and optional drive-in collar)

C: Use a screwdriver to test if deadbolt works smoothly. ?

D: Install strike on the door frame.

IMPORTANT: Make sure the hole in door frame is drilled a minimum of 1" (25mm) deep.

(Diagram shows strike installation with screws and optional reinforcement plate)

STEP 3: Install exterior assembly

IMPORTANT: Before installation, make sure the latch is fully retracted (in the unlocked position). ❌

A: With the latch fully retracted (in the unlocked position), route the cable below the latch, and insert the torque blade through the slot in the latch.

B: Secure the mounting plate with the supplied screws. Do not overtighten screws. Keep parallel to door edge. ?

STEP 4: Install interior assembly

A: Push the battery cover out in the direction as illustrated. ⬆️

IMPORTANT: Do not load batteries until lock is completely installed.

B: Insert the cable connector to the socket. Push the connector in firmly until it is completely attached. ?

C: Keep the thumb turn in vertical position and install the interior assembly. ↔️

D: Attach Interior Assembly to Mounting Plate and tighten 3 Screws. ?

STEP 5: Detect left/right hand door installation

Reset the lock to teach the lock the orientation of the door.

IMPORTANT: This step is required and crucial for the lock to operate properly. ⚠️

A: While the door is OPEN and UNLOCKED, load 3 AA batteries into the battery compartment. Note: For long last, please use all new, non-rechargeable Alkaline batteries only. ?

B: Press and hold the Reset button on the interior assembly by using the reset tool. ?

C: Load the 4th battery and keep holding the reset button for 3 seconds, until you hear the sound of "beep" and the latch will extend to learn the orientation of the door automatically. ?

At a Glance

Exterior Assembly:

• Multi-Function Button (MFB) ☰
• Keypad ?
• Fingerprint ?️
• Keyhole ?

Interior Assembly:

• Battery Cover ?
• Reset Button ?
• Thumb Turn ↪️

How to Use

UNLOCK the door from outside:

1. Enter Master/User code ?
2. Press the button [+]
3. Unlock position ?

LOCK the door from outside:

• Auto Lock Mode: In Auto Lock mode, the bolt will extend out automatically in 30 seconds after unlocking.
• Manual Mode: Press any key on keypad for 2 seconds.

UNLOCK the door from inside:

Rotate the thumb turn to Unlock position. ↪️?

LOCK the door from inside:

• Auto Lock Mode: In Auto Lock mode, the device will be locked automatically.
• Manual Mode: Rotate the thumb turn to Lock Position. ↪️?

Definitions

• Master Code: Required for programming and feature settings. Can be used to unlock the door under vacation mode. Default master code needs to be changed before programming. Keep this information confidential.
• Auto Lock: Automatically locks the deadbolt 30 seconds after unlocking. This feature is off by default. You can customize the Auto Lock time delay between 10 and 99 seconds.
• Key Unlock: Always available when batteries are dead or User Codes are forgotten.
• Low Battery Indicator: 10 beeps and 10 red light flashes indicate the need for battery replacement. Use 4 brand new AA alkaline batteries. Do not mix used and new batteries. Settings are stored when batteries are removed and replaced.
• Wrong Entry Limit: After 10 unsuccessful attempts at entering an invalid PIN code, the unit will shut down for 3 minutes.
• Silent Mode: Keypad beep sounds can be muted. Low battery and system alerts will still be heard.
• Vacation Mode: Security feature for when you are away. Restricts all user codes until the master code is entered. If the lock is unlocked by the thumb turn from inside, it will sound an alarm.
• One Time User Code: Can be used once and is automatically deleted after use.
• Unlock with Fake code: Prevents pin code exposure by entering random digits before or after the pin code. (e.g., 83618 137192 14710)

Code Format

1. Master Code: 4 to 10 digits. Default is 12345678. Change it before programming.
2. User Code: 20 User Codes (4-10 digits), 1 one-time User Code, and 20 fingerprints can be programmed.
3. Invalid Combinations:
• Forward number sequence (e.g., 123456789) ❌
• Backward number sequence (e.g., 987654321) ❌
• Repeat number sequence (e.g., 222222222) ❌
• Contain existing code sequence (e.g., if 568391 exists, then 5683) ❌

Quick Set Up

IMPORTANT: The default Master Code is 12345678. It is required that you change it to a code of your own before programming.

• Change Master Code: [☰] + Master Code + [Wait for long green lights] ➡️ Press 1 ➡️ [Wait for green light flash] ➡️ New Master Code + [Wait for green light flash] ➡️ New Master Code + [Succeed Green light flash]
• Add User Code: [☰] + Master Code + [Wait for long green lights] ➡️ Press 2 ➡️ [Wait for green light flash] ➡️ New User Code + [Wait for green light flash] ➡️ New User Code + [Succeed Green light flash]
• Delete User Code: [☰] + Master Code + [Wait for long green lights] ➡️ Press 3 ➡️ [Wait for green light flash] ➡️ Unwanted User Code + [Succeed Green light flash]
• Add Fingerprint: [☰] + Master Code + [Wait for long green lights] ➡️ Press 4 ➡️ [Wait for green light flash] ➡️ Scan fingerprint 8 times (Each time succeed along with a short beep) ➡️ [Succeed Green light flash + A long beep]
• Delete Fingerprint: [☰] + Master Code + [Wait for long green lights] ➡️ Press 5 ➡️ [Wait for green light flash] ➡️ Scan unwanted fingerprint 1 time ➡️ [Succeed Green light flash + A long beep]
• Silent Mode: [☰] + Master Code + [Wait for long green lights] ➡️ Press 6 ➡️ [Wait for green light flash] ➡️ [1] + [☰] (Silent Mode Disabled Green light flash) or [2] + [☰] (Silent Mode Enabled Green light flash)
• Auto Lock: [☰] + Master Code + [Wait for long green lights] ➡️ Press 7 ➡️ [Wait for green light flash] ➡️ [1] + [☰] (Auto Lock Enabled Green light flash) or [2] + [☰] (Auto Lock Disabled Green light flash)
• Set Auto Lock Time: [☰] + Master Code + [Wait for long green lights] ➡️ Press 8 ➡️ [Wait for green light flash] ➡️ Enter New Duration Time + [ (10-99s) ] ➡️ [Succeed Green light flash]
• Add One-Time Codes: [☰] + Master Code + [Wait for long green lights] ➡️ Press 9 ➡️ [Wait for green light flash] ➡️ New User Code + [Wait for green light flash] ➡️ New User Code + [Succeed Green light flash]
• Enable Vacation Mode: [☰] + Master Code + [Wait for long green lights] ➡️ Press [☰] ➡️ [Wait for green light flash] ➡️ Vacation Mode Enabled (Green light flash)
• Disabled Vacation Mode: Master Code + [Wait for green light flash] ➡️ Vacation Mode Disabled (The door was opened)

Notes:

1. Beeps only sound when the Silent Mode is disabled.
2. If the indicators flash red light, it means your setting failed and it will require to re-enter master mode if you would like to continue your programming.

Factory Default Settings

How to Reset?

IMPORTANT: The resetting will delete all User Codes stored in the lock. ⚠️

1. Keep the door open and unlocked.
2. Press and hold the Reset button, at the same time take out one battery and then place it back.
3. Keep holding the Reset button for 3 seconds, until you hear the sound of "beep" and the latch will extend automatically. ?

Troubleshooting

Why does not the latch extend but the motor is/isn't rotating when resetting my keypad lock?

Improper installation may have caused the issue. Please follow the steps to review:

1. Please make sure the latch and strike are aligned. The deadbolt latch should be retracted(unlocked) through all your installation process.
2. Please recheck if the cable is attached completely in Step 4B.
3. Please make sure the thumbturn is vertical in your installation steps 4C and 5A.
4. Please open your door and reset the lock.

Why doesn't the thumbturn rotate after installation completed?

When the lock is learning wrong orientation of the door, the thumbturn won't rotate. Please reset your lock by following the steps:

1. Keep the door opened and make sure the latch is retracted and thumbturn vertical.
2. Press and hold the reset button with one hand and the other hand take out one battery and place it back.
3. Keep holding the Reset button for 3 seconds, until you hear the sound of "beep" and the latch will extend automatically. ?

If resetting doesn't solve the issue, you may need to re-install the whole lock.

Please make sure when you start to install, the lock is in unlocked status;

Please make sure the thumbturn is vertical.

When I attempt to lock/unlock my deadbolt, why does the latch go in and out for a few times?

It happens when the latch and strike are misaligned.

Please make sure the bolt hole on the door frame is at least 1 inch deep, so that the bolt can be fully extended.

Please check if the door can be closed properly, the deadbolt should not impact the strike or door frame on the door frame side, it should go directly into the hole properly.

Why does my keypad lock only work properly when the backup key is in? Why am I unable to pull the key out in the unlocked position?

You may need to re-install the whole lock.

Please make sure when you start to install, the lock is in unlocked status;

Please make sure the thumbturn is vertical.

Please do not put the backup key in the lock.

What does 5 short and fast beeps mean while programming?

It alerts you either time-out or wrong entry.

• Please be sure to complete each setting step within 5 seconds.
• Please change the default master code in the first time programming.
• Please be sure the user code is with correct format and with 4 to 10 digits.

What if I forget my Master Codes?

If you forget your Master code, resetting your lock, then the original master code (12345678) works, and all previous user codes will be erased.

Information & Safety Warnings

• Protect your User Codes and Master Code.
• Restrict access to your lock's interior assembly and routinely check your settings to ensure they have not been altered without your knowledge.
• Do not use an electric screwdriver during installation. ?
• This manufacturer advises that no lock can provide complete security by itself.
• This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property.
• No lock can substitute for caution, awareness of your environment, and common sense.
• Care should be taken to ensure a long-lasting finish. When cleaning is required use a soft, damp cloth. Using lacquer thinner, caustic soaps, abrasive cleaners or polishes could damage the coating and result in tarnishing.
• The lock is water resistant. It can withstand water splashes; however, do not let water and liquids get into the lock.
• Avoid exposure to direct sunlight. Long-term exposure to direct sunlight may damage the lock.