Hunter Zoanne 6-Light Chandelier Installation

Preparation for Installation

Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old fixture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from the bag.

Step 1: Mount Bracket Assembly
One end of the threaded post (D) should be attached to the mounting bracket (A) with a hex nut (E). The other end should have the canopy loop (G) attached. Unscrew the canopy loop ring (H) from the canopy loop (G).

Step 2: Adjust Threaded Post
Depending on your junction box placement, the position of the threaded post (D) may need adjustment to ensure the canopy (F) sits flush with the ceiling. Lift the mounting bracket (A) to the junction box and place the canopy (F) over the canopy loop (G). Adjust the threaded post (D) on the mounting bracket (A) so the canopy (F) covers at least half of the exterior threads on the canopy loop (G) while securely connected to the threaded post (D). Loosen hex nut (E) to adjust the threaded post (D). Once the ideal position is found, tighten both hex nuts (E) onto the threaded post (D) beneath the mounting bracket (A) to secure it.

Assembling the Fixture

Step 1: Attach Hanging Ring
Adjust the fixture arms to the proper position (refer to diagram 1). Thread wires through and screw the hanging ring (K) onto the threaded post (L) of the fixture.

Step 2: Adjust Chain Length
Measure to determine the correct number of chain links needed for the desired hanging height. If necessary, use pliers to open and remove excess chain. Attach one quick-connect link (J) to each end of the chain (I). Use one quick-connect link (J) to attach chain (I) to the hanging ring (K) and close securely.

Step 3: Feed Wires and Attach Canopy
Feed the fixture wires up through the chain (every three links or so), pulling the wires taut. Slide the canopy loop ring (H) and canopy (F) onto the chain/wire. Thread wires through the canopy loop (G). Use the remaining quick-connect link (J) to attach chain (I) to the canopy loop (G) and close securely.

Step 4: Prepare for Mounting
To shorten the fixture, trim the wires to the desired length, leaving at least 8 to 10 inches of extra wire. Have a helper support the fixture's weight. Attach the mounting bracket (A) to the junction box by securely tightening the mounting screws (C).

Connecting the Wires

Connect the fixture wires to the power supply wires from the junction box:

• Connect Black (fixture) to Black (house) - Live
• Connect White (fixture) to White (house) - Grounded
• Connect Grounding (fixture - green or copper) to Grounding (house - green or copper)

Twist the ends of the wire pairs together and twist on a wire connector. Ensure all twists are in the same direction. Loop the fixture's ground wire around the grounding screw (B) and tighten. If no ground wire is present from the junction box, contact a qualified electrician.

Finishing the Installation

Place the canopy (F) flush to the ceiling and slide the canopy loop ring (H) up beneath the canopy. Tightly screw the canopy loop ring (H) onto the canopy loop (G) to properly secure the canopy (F) in place.

Install light bulbs (not included) according to the fixture's specifications. Do not exceed the recommended wattage. Turn on the power and test the fixture. Your installation is now completed.

Cleaning Tips

Treat the fixture gently! Regular cleaning reduces the need for deep cleaning. For regular cleaning, turn off the light and wipe down the fixture with a clean, lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture.

Hunter Pro Tip: Let the tool do the work! Use chain pliers to easily open and close chain links to shorten your fixture.

Diagram Descriptions

Parts Diagram: Shows fixture components labeled A through L: A - Mounting Bracket, B - Grounding Screw, C - Mounting Screws, D - Threaded Post, E - Hex Nut, F - Canopy, G - Canopy Loop, H - Canopy Loop Ring, I - Chain, J - Quick-Connect Link, K - Hanging Ring, L - Threaded Post.

Wire Connection Diagram: Illustrates wire connections: Fixture wires (Black, White, Green/Copper) connect to House wires (Black, White, Green/Copper). Ground wire loops around grounding screw.

Tools Required Diagram: Shows required tools: Ladder, Screwdriver, Pliers, Wire Strippers.

Chain Adjustment Diagram: Shows the use of pliers to open and close chain links for length adjustment.

Safety Information

⚠️ WARNING

• To avoid possible electrical shock, disconnect power at the circuit breaker before installation.
• The lighting fixture must be grounded. If a ground wire is not present, stop installation and consult a qualified electrician.
• All wiring must comply with national and local electrical codes (ANSI/NFPA 70). Consult a qualified electrician if unfamiliar with wiring.

READ AND SAVE THESE INSTRUCTIONS: These instructions are provided for your safety and should be read carefully and completely before beginning installation.