Product Overview
This document provides detailed instructions for the assembly, operation, and adjustment of the AHOB1085 convertible sofa bed. The sofa bed can be used as a chair or unfolded into a flat sleeping surface.
Parts List
- A x 1: Main frame base
- B x 1: Backrest frame
- C x 1: Seat frame
- D x 1: Extending seat/bed base
- E x 1: Front panel/base
- F x 1: Pillow
- G x 4: Support brackets/hinges
- H x 1: Left arm mechanism
- I x 2: Right arm mechanism
- J x 4: Feet
- K x 1: Seat cushion
- L x 1: Support bar
- M x 1: Support bar
Hardware List
| Item | Description | Quantity |
|---|---|---|
| 1 | M8x60mm screw | 6 |
| 2 | M8 washer | 9 |
| 3 | M8x22mm washer | 9 |
| 4 | M6x19mm screw | 16 |
| 5 | M6 washer | 16 |
| 6 | M6x16mm washer | 16 |
| 7 | M6 rod | 1 |
| 8 | M8 rod | 1 |
| 9 | M8x38mm screw | 3 |
Assembly Instructions
Step 1
Attach part B (backrest frame) to part A (main frame base) using 8x M8x60mm screws (1) and 8x M8 washers (2) and 8x M8x22mm washers (3). Attach the four feet (J) to the underside of part A.
Diagram Description: Shows parts A and B being joined, with hardware 1, 2, 3 indicated. Feet (J) are shown being attached to part A.
Step 2
Assemble the arm mechanisms. Attach the left arm mechanism (H) and right arm mechanism (I) to the frame. Connect support bars (L, M) using M6x19mm screws (4), M6 washers (5), and M6x16mm washers (6). Use rod (7) as indicated.
Diagram Description: Illustrates the attachment of arm mechanisms (H, I) and support bars (L, M) to the main frame. Hardware 4, 5, 6, and rod 7 are shown.
Step 3
Attach the four support brackets/hinges (G) to the frame using M6x19mm screws (4), M6 washers (5), and M6x16mm washers (6).
Diagram Description: Shows support brackets/hinges (G) being attached to the frame using hardware 4, 5, 6.
Step 4
Attach the front panel/base (E) to the main frame. Use 3x M8x38mm screws (9), 3x M8 washers (2), and 3x M8x22mm washers (3).
Diagram Description: Shows the front panel/base (E) being attached to the main frame using hardware 2, 3, 9.
Step 5
Connect the extending seat/bed base (D) to the frame using 4x M6x19mm screws (4), 4x M6 washers (5), and 4x M6x16mm washers (6).
Diagram Description: Shows the extending seat/bed base (D) being connected to the frame using hardware 4, 5, 6.
Step 6
Place the seat cushion (K) onto the assembled sofa bed frame.
Diagram Description: Shows the seat cushion (K) being placed onto the assembled frame.
Step 7
Illustration of a close-up of a latch mechanism on the sofa bed frame, with an arrow indicating its operation for securing or releasing a part.
Diagram Description: Close-up of a latch mechanism.
Step 8
Illustration of the sofa bed in its chair configuration. The extending seat/bed base is shown partially pulled out, with arrows indicating the direction of movement for unfolding.
Diagram Description: Sofa bed in chair form, with the extending base partially pulled out.
Operation and Adjustment
Step 9
Illustration of the fully assembled sofa bed in its upright chair position, with a pillow (F) on the seat.
Diagram Description: Sofa bed in upright chair position with pillow.
Step 10
The sofa bed's backrest can be adjusted to multiple positions, including a flat sleeping surface. The adjustment sequence is as follows:
- Put it flat and lift it once: for first gear.
- Up again: second gear.
- Lift it up again: third gear.
- Put it up again: fourth gear.
- Up again: Back to flat.
Diagram Description: Diagram illustrating the adjustment mechanism for the backrest, showing arrows for lifting and tilting to achieve different positions.
Step 11
Sequence of diagrams illustrating the process of unfolding the sofa bed into a flat sleeping surface. The steps involve pulling out the seat/bed base and then lowering the backrest and seat to form a bed.
Diagram Description: Sequence of illustrations showing the sofa bed unfolding into a flat bed.
