Assembly Instructions
This document provides comprehensive assembly instructions for various furniture items, including a bed, a nightstand, and a dresser with a mirror. It covers tools required, pre-assembly tips, care advice, parts and hardware lists, step-by-step assembly guides, and wall mounting instructions.
General Information
Tools Required
- Screwdriver (Not Included) ?
- Allen Wrench (Included) ?️
- 2 People Recommended ???
Assembly Rating
The Assembly Rating is a 5-point system showing the level of effort needed to assemble a specific product, ranging from EASY to DIFFICULT.
Pre-Assembly Introduction
We understand building ready-to-assemble furniture can be challenging. To help avoid confusion, we have provided some helpful tips that may speed up the process.
- Teamwork: ALWAYS have at least two people to help with transporting and assembling the product to avoid potential injury and/or damage. [Illustration showing two people carrying furniture]
- Suitable Location: Assembling near the area of the intended location is highly recommended. [Illustration showing furniture being assembled near its final location]
- Sufficient Space: Make sure you have enough space to move around during the assembly. [Illustration showing ample space around furniture assembly]
- Avoid Scratches: Use cardboard, blankets, or a carpeted area while assembling furniture to prevent scratches. [Illustration showing furniture being protected from scratches with cardboard]
- Flat Surface: Make sure the furniture rests on a flat and level surface with each leg evenly touching the floor. [Illustration showing furniture on a flat surface]
Assembly and Care Advice
⚠️ FAILURE TO FOLLOW THE GUIDELINES BELOW MAY RESULT IN INJURY AND/OR PROPERTY DAMAGE.
- Position each part correctly and insert screws or bolts into their respective holes. [Illustration of a screw being inserted into a hole]
- Use the appropriate hand tools or power tools for assembly. Select steps, such as tightening screws and/or bolts, may require hand tools to avoid causing damage during assembly. [Illustration of hand tools (wrench, screwdriver)]
- Turn clockwise to tighten and only tighten when step is completed or when instructed to do so. [Illustration of a screwdriver tightening a screw]
- Save the instructions and store any supplied tools for later maintenance.
- After two weeks, check and tighten any loose hardware and repeat again every six months thereafter.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE. THE HARDWARE MAY LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE SERIOUS INJURY.
Bed Assembly Instructions
Please keep instructions for future reference. Check the quantity and irregularity of parts and hardware before you start.
Parts List
| Part ID | Description | Quantity | Diagram |
|---|---|---|---|
| #1 | Headboard leg (L.R) | 2pcs | [Illustration of a long, vertical piece with pre-drilled holes and mounting points] |
| #2 | Headboard bottom rail | 1pc | [Illustration of a horizontal rail with mounting brackets] |
| #3 | Headboard | 1pc | [Illustration of the main headboard panel] |
| #4 | Storage footboard | 1pc | [Illustration of the footboard panel] |
| #5 | Side rail | 2pcs | [Illustration of a long horizontal rail] |
| #6 | Center support rail | 1pc | [Illustration of a central rail that runs lengthwise under the slats] |
| #7 | Long support leg | 3pcs | [Illustration of a leg that supports the center rail] |
| #8 | Short support leg | 1pc | [Illustration of a shorter leg] |
| #9 | Slat | 1set (13pcs) | [Illustration of multiple wooden slats] |
Hardware List
| Part ID | Description | Quantity | Diagram |
|---|---|---|---|
| #A | Bolt Ø5/16" x 5/8" | 8pcs | [Illustration of a bolt] |
| #B | Bolt Ø5/16" x 1-1/2" | 10pcs | [Illustration of a longer bolt] |
| #C | Lock washer Ø5/16" | 10pcs | [Illustration of a split lock washer] |
| #D | Washer Ø5/16" x 19mm | 10pcs | [Illustration of a flat washer] |
| #E | Allen Key 4mm | 2pcs | [Illustration of an L-shaped Allen key] |
| #F | Screw #4 x 1-3/16" | 26pcs | [Illustration of a wood screw] |
Assembly Steps
- Step 1: Attach the Headboard bottom rail (#2) to the Headboard legs (#1, L.R). Use 2x Bolt (#B), 2x Lock washer (#C), 2x Washer (#D), and 1x Allen Key (#E). [Diagram showing #2 connecting to #1,L and #1,R with hardware]
- Step 2: Attach the Headboard (#3) to the assembled structure from Step 1. Use 8x Bolt (#B), 8x Lock washer (#C), 8x Washer (#D), and 1x Allen Key (#E). [Diagram showing #3 attaching to the headboard assembly with hardware]
- Step 3: Attach the Storage footboard (#4) and Side rails (#5) to the frame. Use 8x Bolt (#A) and 1x Allen Key (#E). [Diagram showing #4 and #5 being attached to the frame with hardware]
- Step 4: Attach the Center support rail (#6) and Long support legs (#7), and Short support leg (#8). [Diagram showing #6, #7, and #8 being attached]
- Step 5: Place the Slats (#9) onto the support rails. (1 SET = 13pcs). [Diagram showing slats being placed]
- Step 6: Secure the Slats (#9) to the frame using 26x Screw (#F). [Diagram showing screws being inserted into slats]
Note: This product is intended for RESIDENTIAL USE ONLY and not for commercial use.
Nightstand Assembly Instructions
Please keep instructions for future reference. Check the quantity and irregularity of parts and hardware before you start.
Parts List
| Part ID | Description | Quantity | Diagram |
|---|---|---|---|
| #1 | Desk | 1pc | [Illustration of a nightstand desk] |
Hardware List
| Part ID | Description | Quantity | Diagram |
|---|---|---|---|
| #A | Anti-tip Skit | 1set | [Illustration of an anti-tip kit] |
Assembly Steps
- Step 1: Wall Mounting and Fixing: Secure the Nightstand to the wall using the Anti-tip Skit (#A). [Diagram showing the nightstand, wall, and anti-tip hardware installation]
- Expansion Wall Anchor: Our provided expansion wall anchors are only suitable for masonry walls, such as drywall, plaster or concrete, and are best for holding lightweight items or for anti-tip prevention. If you are unsure of the correct wall anchor to use with the product, please request professional guidance. Liability for product damage or failure due to using the incorrect anchors will fall on the installer.
- Check Before Proceeding: Prior to drilling or hammering, please check for wires or pipes. We recommend using a stud finder to locate a stud, which will offer more appropriate resistance and hold more weight.
- Quick Tips:
- If unsure of the proper size, always choose a larger screw and wall anchor.
- Match the drill bit to the wall anchor and hole size.
- Only drill horizontally. Do not force the drill or enlarge the hole for the wall anchor. ?
- Take extra care when drilling into high walls or ceramic tiles. Wall anchors should be a tight fit for the hole. Never use wall anchors in ceilings.
- Step 2: Assembly Completed:
- Please ensure the furniture rests on an even and flat surface. If the product wobbles or feels loose, double-check all bolts and/or screws are properly tightened and secured. ✔️
- Keep this handy! Please retain this instruction manual and any order-related information for future reference. ?️
- Lift, don't drag! To avoid damage to product, please always LIFT the product when transporting or adjusting the placement. ⬆️
Note: This product is intended for RESIDENTIAL USE ONLY and not for commercial use.
Maintenance
We recommend a yearly check to see if the wall anchor or screw has loosened. If so, please remove the existing wall anchor and screw, and use a new anchor. ⚙️
Dresser & Mirror Assembly Instructions
Please keep instructions for future reference. Check the quantity and irregularity of parts and hardware before you start.
Parts List
| Part ID | Description | Quantity | Diagram |
|---|---|---|---|
| #1 | Desk | 1pc | [Illustration of a dresser desk] |
| #2 | Support bar | 2pcs | [Illustration of a support bar] |
| #3 | Mirror | 1pc | [Illustration of a mirror] |
Hardware List
| Part ID | Description | Quantity | Diagram |
|---|---|---|---|
| #A | Bolt Ø1/4" x 1-1/2" | 8pcs | [Illustration of a bolt] |
| #B | Lock washer Ø1/4" | 8pcs | [Illustration of a lock washer] |
| #C | Washer Ø5/16" x 19mm | 8pcs | [Illustration of a washer] |
| #D | Allen Key 4mm | 1pc | [Illustration of an Allen key] |
| #E | Anti-tip Skit | 1set | [Illustration of an anti-tip kit] |
Assembly Steps
- Step 1: Attach the Support bars (#2) to the Desk (#1). Then, attach the Mirror (#3) to the Support bars. Use 8x Bolt (#A), 8x Lock washer (#B), 8x Washer (#C), and 1x Allen Key (#D). [Diagram showing #2 attaching to #1, and #3 attaching to #2 with hardware]
- Step 2: Wall Mounting: Secure the Dresser & Mirror to the wall using the Anti-tip Skit (#E). [Diagram showing the dresser & mirror, wall, and anti-tip hardware installation]
- Expansion Wall Anchor: Our provided expansion wall anchors are only suitable for masonry walls, such as drywall, plaster or concrete, and are best for holding lightweight items or for anti-tip prevention. If you are unsure of the correct wall anchor to use with the product, please request professional guidance. Liability for product damage or failure due to using the incorrect anchors will fall on the installer.
- Check Before Proceeding: Prior to drilling or hammering, please check for wires or pipes. We recommend using a stud finder to locate a stud, which will offer more appropriate resistance and hold more weight.
- Quick Tips:
- If unsure of the proper size, always choose a larger screw and wall anchor.
- Match the drill bit to the wall anchor and hole size.
- Only drill horizontally. Do not force the drill or enlarge the hole for the wall anchor. ?
- Take extra care when drilling into high walls or ceramic tiles. Wall anchors should be a tight fit for the hole. Never use wall anchors in ceilings.
Note: This product is intended for RESIDENTIAL USE ONLY and not for commercial use.
Maintenance
We recommend a yearly check to see if the wall anchor or screw has loosened. If so, please remove the existing wall anchor and screw, and use a new anchor. ⚙️
Assembly Completed
Please ensure the furniture rests on an even and flat surface. If the product wobbles or feels loose, double-check all bolts and/or screws are properly tightened and secured. ✔️
Keep this handy! Please retain this instruction manual and any order-related information for future reference. ?️
Lift, don't drag! To avoid damage to product, please always LIFT the product when transporting or adjusting the placement. ⬆️
