Introduction
The WG-Z ZigBee Gateway is a wireless gateway featuring integrated Wi-Fi and low-power wireless Zigbee modules. It enables users to control smart home devices through the TUYA Smart Life App, supporting functions like device adding, resetting, third-party control, and Zigbee group control. It is compatible with various Zigbee LED controllers, dimmers, and drivers for smart home applications.
Features
- Plug and play, easy to use.
- Integrated with WiFi and Zigbee communication modes for remote WiFi control and local Zigbee control.
- Stable and reliable WiFi and Zigbee signals provide wide coverage, prevent interference, and offer lower power consumption.
- Employs industry-advanced encryption for secure transmission of information on both WiFi and Zigbee terminals.
- Multiple Zigbee gateways can be connected within the same local area network via the Smart Life App.
- A long press of the reset key for 5 seconds clears previous connections and rapidly enters configuration mode.
Technical Parameters
1. Physical Characteristics
| Specification | Details |
|---|---|
| State indicator | Two LEDs (Wi-Fi+Zigbee) |
| Operation key | One key (for resetting) |
| Input voltage | MicroUSB DC5V |
| Input current | <1A |
| Operation temperature | -10-55°C |
| Operation humidity | 10%-90%RH (non-condensable) |
| Storage temperature | -20-60°C |
| Storage humidity | 5%-90%RH (non-condensable) |
| Hardware port | One Micro-USB |
| Wireless technology | Wi-Fi 802.11 b/g/n, Zigbee 802.15.4 |
| Type of antennae | Built-in on-board antenna |
2. RF Characteristics
| Specification | Wi-Fi | Zigbee |
|---|---|---|
| Wireless frequency | 2.400~2.4835GHz | 2.400-2.480 GHz |
| Transmitting power | 21dBm | 10dBm (Standard) |
| Signal channels | CH1-CH11 | CH1-CH26 |
| Transmitting rate | 11b: 1, 2, 5.5, 11 (Mbps) 11g: 6, 9, 12, 18, 24, 36, 48, 54 (Mbps) 11n: HT20 MCS0~7 11n: HT40 MCS0~7 | 250Kbps |
3. Network Performance
| Specification | Details |
|---|---|
| Wireless encryption | AES 128bit Encryption |
| Security mechanism | WPA-PSK/WPA2-PSK, WPA/WPA2 |
| Network administration | App remote configuration, Wi-Fi module firmware upgrade, Zigbee module firmware upgrade |
| The number of connecting sub-devices | Max Node = 50 |
4. State Indicator & Reset
Blue Light (Zigbee State)
- Blinking: Gateway is waiting for connection and allowed to access the network.
- Indicator keeps on: Gateway is not activated.
- Indicator keeps off: Gateway has been activated.
Red Light (Wi-Fi State)
- Indicator keeps on: Gateway has been connected.
- Blinking: Gateway is waiting for connection.
- Indicator keeps off: Gateway has configured Wi-Fi, but is unable to connect to Wi-Fi.
Method for Resetting
After a long press of the reset key for 5 seconds, the red LED indicator flashes quickly.
Mechanical Structure and Installation
The device features a Micro USB socket, a reset key, a Blue/Red LED indicator, and a DC 5-24V power socket.
System Wiring
The system wiring illustrates the connectivity of the WG-Z ZigBee Gateway:
- Internet Connectivity: 3G/4G/5G WiFi connects to a WiFi router, which then connects to a mobile phone.
- Cloud Services: Tuya cloud connects to the WiFi router. Amazon ECHO connects to Tuya cloud.
- Gateway Connection: The WG-Z Wireless Zigbee Gateway connects wirelessly to the WiFi router.
- Device Connections:
- WZ5 LED controller (for RGB+CCT strips) connects to the gateway within a 15m range.
- S1-B(WZ) Triac dimmer (for Dimmable LED lights) connects within a 30m range.
- SS-B(WZ) RF Switch (for Non-dimming LED lights) connects within a 30m range.
- L1(WZ) 0/1-10V dimmer (for 0-10V dimmable LED drivers) connects within a 30m range.
- Optional Control: Panel RF Remotes can also be connected.
Note: The specified distances are measured in spacious environments without obstacles. Actual distances may vary based on installation conditions.
Preparation for Usage
Download and Open APP
Download and install the "Smart Life" app by searching in the App Store or Google Play, or by scanning the provided QR code.
Operation
Tuya APP Cloud Control
- Power on the gateway.
- Ensure the gateway's red LED indicator is blinking. If it is in a different state, long press the reset key until the indicator flashes.
- Connect your mobile phone to Wi-Fi. Your phone and the gateway should be on the same local area network.
- Open the Smart Life app, tap the
[+]icon in the upper right corner, select "Gateway Control", and then tap "Wireless Gateway (Zigbee)". - After successfully adding the gateway, tap the "Gateway" icon on the home page and add sub-devices according to the app's prompts.
Voice Control (Amazon ECHO)
- Power on the gateway.
- Ensure your phone's Wi-Fi, Bluetooth, and location services are enabled.
- Ensure the gateway's red LED indicator is blinking. If it is in a different state, long press the reset key until the indicator flashes.
- Open the Smart Life app, tap the
[+]icon in the upper right corner, select "Gateway Control", and then tap "Wireless Gateway (Zigbee)". - After successfully adding the gateway, click the "Gateway" icon on the home page and add other sub-devices.
- Ensure Amazon ECHO is powered on.
- Connect Amazon ECHO to the internet via the Amazon Alexa App.
- In the Alexa app menu, navigate to "Skills & Games".
- Search for "Smart Life" or "Tuya Smart", and tap "Enable" to activate the Skill.
- Enter your Smart Life App account and password, then tap "Link Now" to connect your Smart Life account.
- Once the Smart Life account is successfully linked, you can control sub-devices connected to the gateway using voice commands.
Notice for Applications
- If the gateway fails to connect to Wi-Fi, verify that your phone is connected to Wi-Fi and that Bluetooth and location services are enabled. If problems persist, long press the reset key for 5 seconds until the indicator flashes rapidly.
- The gateway must remain connected to a power socket at all times during operation.
- For optimal and stable connection, it is recommended to install the gateway in a central location relative to all sub-devices. Position it 2-6 meters away from the Wi-Fi router. The distance between the gateway and sub-devices should not exceed 20 meters, and there should be no more than two walls between them.
- Avoid placing the gateway near metal obstructions or load-bearing walls that could interfere with the signal between the gateway and the router or sub-devices. Thicker solid walls or high-power electrical appliances (such as refrigerators, air conditioners, or electric heaters) located between the gateway and sub-devices can reduce the effective communication distance to approximately 3-5 meters.
- Your mobile phone must be connected to Wi-Fi before you can connect sub-devices to the gateway using the Tuya App.
- The maximum number of sub-devices that can be connected to a single gateway is 50.
