Redmi Note 14 Pro

Device Overview

The Redmi Note 14 Pro features the following:

• Volume Button
• Power Button
• USB Type-C Port

READ THIS DOCUMENT BEFORE USING YOUR PRODUCT

Thank you for choosing the Redmi Note 14 Pro. Press and hold the Power button to turn on the device. Follow the on-screen instructions to complete the setup. For more information, visit our official website: www.mi.com/global/service/userguide

About SIM

Do not insert non-standard SIM cards into the SIM card tray. It may damage the SIM card tray. WARNING: Do not disassemble this device.

WEEE

Correct disposal of this product: This symbol indicates that this product should not be disposed of with other waste. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle responsibly to promote the sustainable reuse of resources. To return your used appliance, use an authorized collection system or contact where you purchased the product. They can take this product for safe recycling.

CAUTION

Risk of battery explosion if replaced with an incorrect type. Dispose of used batteries according to instructions.

To prevent possible hearing damage, do not listen at high volume for prolonged periods.

For safety information, refer to the user manual at the following link: www.mi.com/en/certification

Important Safety Information

Read all safety information below before using your device.

• Using unauthorized cables, power adapters, or batteries may cause fires, explosions, or other risks.
• Use only authorized accessories that are compatible with your device.
• The operating temperature range for this device is 0°C~40°C. Using this device in environments outside this temperature range may damage the device.
• If your device has a built-in battery, do not attempt to replace the battery yourself to avoid damaging the battery or the device.
• Charge this device only with the included or authorized power cable and adapter. Using other adapters may cause fires, electric shocks, and damage to the device and adapter.
• Once charging is complete, disconnect the adapter from both the device and the power outlet. Do not charge the device for more than 12 hours.
• The battery must be recycled or disposed of separately from household waste. Improper handling of the battery may cause a fire or explosion. Dispose of or recycle the device, its battery, and accessories in accordance with local regulations.
• Do not disassemble, strike, crush, or burn the battery. In case of deformation, stop using the battery immediately.
• Do not short-circuit the battery to avoid overheating, burns, or other personal injury.
• Do not place the battery in high-temperature environments. Overheating may cause an explosion.
• Do not disassemble, strike, or crush the battery to avoid leaks, overheating, or explosion.
• Do not burn the battery to avoid fires or explosions.
• In case of deformation, stop using the battery immediately.
• The user shall not remove or alter the battery. Battery removal or repair should only be performed by an authorized manufacturer repair center.
• Keep your device dry.
• Do not attempt to repair the device yourself. If any part of the device does not function properly, contact Mi customer service or take your device to an authorized repair center.
• Connect other devices according to their instruction manuals.
• Do not connect incompatible devices to this device.
• For the AC/DC adapter, the power outlet should be close to the equipment and easily accessible.

Safety Precautions

Observe laws and rules that restrict the use of mobile phones in specific cases and environmental conditions.

Do not use your phone in gas stations, explosive atmospheres, or potentially explosive environments, including fuel supply areas, under boat decks, fuel or chemical product transfer or storage facilities, areas where the air contains chemicals or particles, such as grains, dust, or metal powders. Obey all signage to turn off wireless devices such as your phone or other radio equipment. Turn off your mobile phone or wireless device when in a blasting area or in areas posted to turn off "two-way radios" or "electronic devices" to avoid interfering with blasting.

Do not use your phone in operating rooms, emergency rooms, or intensive care units. Comply with the rules and regulations of hospitals and health centers. Consult your doctor and the device manufacturer to determine if your phone's operation may interfere with the operation of your medical device. To avoid possible interference with a pacemaker, maintain a minimum separation of 15cm between the mobile phone and the pacemaker. To achieve this, use the phone on the ear opposite your pacemaker and do not carry it in your chest pocket. Do not use your phone near hearing aids, cochlear implants, etc., to avoid interference with medical equipment.

Respect aviation safety regulations and turn off your phone on board aircraft when necessary.

When driving a vehicle, use your phone in accordance with relevant traffic laws and regulations.

To avoid lightning strikes, do not use your phone outdoors during electrical storms.

Do not use your phone to make calls while it is charging.

Do not use your phones in humid places, such as bathrooms. Doing so may cause electric shocks, injuries, fires, and damage to the charger.

Safety Notice

Update your phone's operating system using the built-in software update function, or visit our authorized service points. Software updates via other means may damage the device or cause data loss, security issues, and other risks.

EU Regulation

RED Declaration of Conformity

[CE mark]

Hereby, Xiaomi Communications Co., Ltd. declares that this GSM/GPRS/EDGE/UMTS/LTE mobile phone with Bluetooth and WiFi 24116RACCG is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. The full text of the EU declaration of conformity can be found at www.mi.com/en/certification

Information on Radiofrequency (RF) Exposure (Specific Absorption Rate, SAR)

This device complies with the government's requirements for radio wave exposure. This device is designed and manufactured not to exceed emission limits for radiofrequency (RF) energy exposure. The standard exposure for wireless devices uses a unit of measurement known as the specific absorption rate, or SAR. The SAR limit imposed by the FCC is 1.6W/kg.

For body-worn portable operation, this device has been tested and complies with the FCC RF exposure guidelines for use with an accessory that does not contain metal and is positioned at a minimum of 1.5cm from the body. The safety of RF exposure from any body-worn accessory containing metal has not been verified or certified, so the use of such an accessory should be avoided. The accessory is available on the market and should be used to maintain a 1.5cm distance between the device EUT and the body.

Legal Information

This device may be operated in all EU member states. Observe local and national regulations where the device is used.

This device is restricted for indoor use only when operating in the frequency range of 5250 to 5350MHz in: AT, BE, BG, HR, CY, CZ, DK, EE, FI, FR, DE, EL, HU, IE, IT, LV, LT, LU, MT, NL, PL, PT, RO, SK, SI, ES, SE, UK(NI), IS, LI, NO, CH, TR.

Wi-Fi connectivity (including Wi-Fi frequency bands, Wi-Fi standards, and other functions as ratified in the IEEE 802.11 standard specifications) may vary depending on regional availability and local network compatibility. The function can be added via OTA when and where applicable.

Ensure that the power adapters used comply with the applicable country regulations and international and regional safety standards.

Frequency Bands and Power

This mobile phone offers the following frequency bands only in EU areas and a maximum radio frequency power:

• GSM 850: 33.5dBm
• GSM 900: 35.5dBm
• GSM 1800: 32.5dBm
• GSM 1900: 30.5dBm
• WCDMA Band 1/8: 25.7dBm
• LTE Band 1/3/7/8/20/28/38/40/41: 25.7dBm
• Bluetooth: 20dBm
• 2.4GHz Wi-Fi Band: 20dBm
• 5GHz Wi-Fi: 5150MHz to 5250MHz 23dBm / 5250MHz to 5350MHz 20dBm / 5470MHz to 5725MHz 20dBm / 5725MHz to 5850MHz 14dBm
• NFC: 13.56MHz < 42dBuA/m at 10m

FCC Regulation

This phone complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This phone has been tested and complies with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Therefore, there is no guarantee that interference will not occur in a particular installation if this equipment causes harmful interference to radio or television reception, which can be determined by turning the device on or off. The user is encouraged to try to correct interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet or circuit different from that to which the receiver is connected.
• Consult a dealer or an experienced radio/TV technician for help.

RF (SAR) Exposure Information

This device complies with the government's requirements for radio wave exposure. This device is designed and manufactured not to exceed emission limits for radiofrequency (RF) energy exposure. The standard exposure for wireless devices uses a unit of measurement known as the specific absorption rate, or SAR. The SAR limit imposed by the FCC is 1.6W/kg.

For body-worn portable operation, this device has been tested and complies with the FCC RF exposure guidelines for use with an accessory that does not contain metal and is positioned at a minimum of 1.5cm from the body. The safety of RF exposure from any body-worn accessory containing metal has not been verified or certified, so the use of such an accessory should be avoided. The accessory is available on the market and should be used to maintain a 1.5cm distance between the device EUT and the body.

FCC Note

Changes or modifications not expressly approved by the party responsible for compliance may void the user's authority to operate the equipment.

To comply with FCC Class B limits, shielded cables must be used.

Electronic Label

This device has an electronic label for certification information. To access it, select Settings > About phone > Certification or select Settings and type "Certification" in the search bar.

Certification Information (Highest SAR)

• SAR Limit 10g: 2.0W/kg
• SAR: Head: 0.80W/kg Body: 0.98W/kg (5mm distance)
• SAR Limit 1g: 1.6W/kg SAR Value: Head: 1.03W/kg
• Body-worn: 0.99W/kg (15mm distance)
• Hotspot: 1.01W/kg (10mm distance)

Model Information

Model: 24116RACCG

2411 indicates the product launch will be after 202411.

NOM

OPERATION OF THIS DEVICE IS SUBJECT TO THE FOLLOWING CONDITIONS:

• a) This equipment or device may not cause harmful interference.
• b) This equipment or device must accept any interference, including that which may cause undesired operation.

CONNECTION INSTRUCTIONS:

1. To connect your mobile phone to electrical power and recharge the internal battery, use only your battery charger provided with the equipment.
2. Connect the USB cable to the phone's USB port.
3. Connect the USB cable to the battery charger's USB port.
4. Connect the charger to an AC power outlet (100V-240V~).
5. To disconnect the charger when the battery is recharged, hold the charger firmly and remove it from the AC outlet; never pull the cable.

IMEI Location

The IMEI is located on a label attached to the back of your equipment and on the label attached to the box.

To get your equipment's IMEI, press the "phone" icon and dial *#06# or consult it in "Settings" > "About phone" > "All specifications" > "Status" > "IMEI".

Geographic location of the mobile phone

To geolocate your mobile phone, the equipment must have the following configurations enabled:

1. A Mi account or a Google account linked and active on the equipment.
2. Internet connection via mobile data and/or WiFi.
3. "Location" functionality enabled.

Location via your MI account

To locate the mobile phone online via your Mi account, go to the following site and log in with the Mi account linked to the mobile phone: https://i.mi.com/?_locale=es_US

Once logged in, you can check your device's location.

Location via your Google account

To locate the mobile phone online via your Google account, go to the following site and log in with the Google account linked to the mobile phone: https://myaccount.google.com/find-your-phone

Once logged in, you can check your device's geographic location.

Protecting your phone's content

To protect your phone's content, you can use the following screen lock functionalities:

1. Pattern lock
2. PIN
3. Password
4. Fingerprint
5. Facial unlock

To access and configure these options, go to: "Settings" / "Passwords & security"; in this menu, you can choose your preferred screen lock method.

Using the FM Radio

For the FM Radio function, press the "Home"/"Tools"/"FM Radio" button; headphones must be connected as they function as an antenna.

Power: 5 Vdc 3 A / 5 Vdc to 11 Vdc 4.1 A (45 W Max)

Adapter:

• Input: 100 V-240 Vac 50 Hz/ 60 Hz 1.1 A
• Output: 5 Vdc 3 A / 5 Vdc to 11 Vdc 4.1 A (45 W Max)

Uses 1 rechargeable Lithium-ion Polymer battery of 3.91 Vdc 5 350 mAh/5 500 mAh 20.92 Wh/21.51 Wh

Cell Broadcast (CBS) is a function that offers SMS decoding, supports geofencing for emergency and non-emergency wireless alerts, and provides information to end-users based on regional and mobile carrier regulations.

This device supports the CBS function and complies with Part 3 of the IFT-011-2022 standard. To access the CBS configuration menu, go to Settings > Security & emergency > Wireless emergency alerts, and select the "on" or "off" options to receive or not receive the corresponding alerts.

Legal Notice

This user guide is published by Xiaomi or its local subsidiary. If necessary, Xiaomi may make improvements or changes related to typographical errors or inaccurate current information in this user guide, or improvements to programs or equipment, without prior notice and at any time. Such changes, however, will be incorporated into new online editions of this user guide (see more details at www.mi.com/global/service/userguide). All images are for reference only and may not accurately represent the actual device.

Importer:

XIAOMI SOFTWARE DE MEXICO, S. de R.L. de C.V.
RFC: XSM2107156A3
BLVD. LAGO ZURICH 219, PISO 9 902 Y 903,
AMPLIACION GRANADA, MIGUEL HIDALGO,
CIUDAD DE MEXICO, C.P. 11529.

Manufacturer:

Xiaomi Communications Co., Ltd.
Manufacturer's postal address: #019, 9th Floor, Building 6,
33 Xi'erqi Middle Road, Haidian District, Beijing, China, 100085

Mobile Phone

Brand: Redmi

Model: 24116RACCG

All rights reserved by Xiaomi Inc.